Modification of TiO2 with sulfate and phosphate for enhanced eosin Y-sensitized hydrogen evolution under visible light illumination

Impact of TiO2 Reduction and Cu Doping on Bacteria Inactivation under Artificial Solar Light Irradiation

Preparation of TiO₂ using the hydrothermal treatment in NH₄OH solution and subsequent thermal heating at 500-700 °C in Ar was performed in order to introduce some titania surface defects. The highest amount of oxygen vacancies and Ti³⁺ surface defects were observed for a sample heat-treated at 500 °C. The presence of these surface defects enhanced photocatalytic properties of titania towards the deactivation of two bacteria species, E. coli and S. epidermidis, under artificial solar lamp irradiation. Further modification of TiO₂ was targeted towards the doping of Cu species. Cu doping was realized through the impregnation of the titania surface by Cu species supplied from various copper salts in an aqueous solution and the subsequent heating at 500 °C in Ar. The following precursors were used as a source of Cu: CuSO₄, CuNO₃ or Cu(CH₃COO)₂. Cu doping was performed for raw TiO₂ after a hydrothermal process with and without NH₄OH addition. The obtained results indicate that Cu species were deposited on the titania surface defects in the case of reduced TiO₂, but on the TiO₂ without NH₄OH modification, Cu species were attached through the titania adsorbed hydroxyl groups. Cu doping on TiO₂ increased the absorption of light in the visible range. Rapid inactivation of E. coli within 30 min was obtained for the ammonia-reduced TiO₂ heated at 500 °C and TiO₂ doped with Cu from CuSO₄ solution. Photocatalytic deactivation of S. epidermidis was greatly enhanced through Cu doping on TiO₂. Impregnation of TiO₂ with CuSO₄ was the most effective for inactivation of both E. coli and S. epidermidis.

Photocatalytic evaluation and characterization of TiO2-riboflavin phosphate film: analysis of reactive oxygen species

The effect of Riboflavin-5'-phosphate (RFPO₄) sensitization on photocatalytic properties of TiO₂ film was studied. RFPO₄ was adsorbed on film surface to investigate the photophysical properties of TiO₂ upon blue-light photoexcitation. The film was characterized through scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, thermogravimetric analysis, and diffuse reflectance spectroscopy. The efficiency of the TiO₂/RFPO₄ film was tested for pollutant elimination in aqueous media in a visible-light-driven system. The phenol paradigmatic model was employed in an aqueous solution as a contaminant target. TiO₂/RFPO₄ sensitized photodegradation of phenol, which produces catechol, hydroquinone, and benzophenone, was monitored by absorption spectroscopy and HPLC. The results indicated that phenol degradation with TiO₂/RFPO₄ film was due to the photogeneration of two reactive oxygen species, singlet molecular oxygen (O₂(¹Δ_g)) and superoxide radical anion (O₂^·-) identified through specific detection techniques. The presence of O₂(¹Δ_g) is reported here for the first time as generated from a sensitized TiO₂ film upon visible-light photoirradiation. Based on the photophysical determinations, a photocatalytic mechanism for TiO₂/RFPO₄ was established.

ATR FTIR Study of the Interaction of TiO2 Nanoparticle Films with β-Lactoglobulin and Bile Salts

The technique of in situ particle film attenuated total reflection Fourier transform infrared spectroscopy (ATR FTIR) has been used to probe the adsorption and coadsorption (sequential) of a common food protein (β-lactoglobulin, BLG) and two representative bile salts (taurocholic acid and glycocholic acid, abbreviated as TCA and GCA) onto the surface of titanium dioxide (TiO₂) nanoparticles. Evaluating of binding interactions between commonly used (historically now, in some countries) food additives and food components, as well as the body's own digestion chemicals, is a critical step in understanding the role of colloidal phenomena in digestion and bioavailability. TCA is found to adsorb onto TiO₂ but without any significant ability to be retained when it is not present in the aqueous phase. GCA is also found to adsorb via two distinct binding mechanisms, with one type of adsorbed species being resistant to removal. BLG adsorbs, is irreversibly bound, and has altered conformation when adsorbed at pH 2 (stomach conditions) to the conformation when adsorbed at pH 6.5 (small intestine conditions). This altered conformation is not interface-dependent and is mirrored in the solution spectra of BLG. Sequential coadsorption studies indicate that TCA and GCA adsorb onto TiO₂ nanoparticle surfaces and display similar degrees of reversibility and binding in the presence or absence of preadsorbed BLG.

Two Tungstates Containing Platinum Nanoparticles Prepared by Air-Calcining Keggin-Type Polyoxotungstate-Coordinated Diplatinum(II) Complexes: Effect on Sintering-Resistance and Photocatalysis

Two tungstates containing platinum nanoparticles (Pt Npts) were obtained by air-calcining α-Keggin-type diplatinum(II)-coordinated polyoxotungstates, Cs3[α-PW11O39{cis-Pt(NH3)2}2]⋅8H2O (Cs-P-Pt) and Cs4[α-SiW11O39{cis-Pt(NH3)2}2]⋅11H2O (Cs-Si-Pt), at 700–900 °C for 5 h. The polyoxotungstate Cs-P-Pt was transformed to a mixture of Pt Npts and Cs3PW12O40 upon calcination, while the Cs-Si-Pt structures were transformed to Pt Npts and Cs4W11O35. The Pt Npts generated by air-calcining Cs-P-Pt at 700 °C for 5 h were uniform with an average particle size of 3.6 ± 1.1 nm, which was much smaller than that of the Pt Npts obtained by calcining Cs-Si-Pt (19.9 ± 9.9 nm) under identical conditions. This demonstrated the significant inhibitory effect of Cs-P-Pt on aggregation during high-temperature air-calcination at a high platinum content (10.6 wt.%) and in the absence of a support. During calcination at 700–900 °C, Cs-P-Pt exhibited higher activities than Cs-Si-Pt with respect to hydrogen evolution from aqueous triethanolamine solutions under visible light irradiation in the presence of Eosin Y, α-Keggin-type mono-aluminum-substituted polyoxotungstate, and titanium dioxide. When Cs-P-Pt was calcined at 800 °C for 100 h, no decrease in activity was observed in comparison with that upon calcination for 5 h.

Graphical Abstract

Combination of microwave discharge electrodeless lamp and a TiO2/HZSM-5 composite for the photocatalytic degradation of dimethyl sulphide

In this study, an integrated photocatalytic system consisting of a microwave discharge electrodeless lamp (MDEL) and TiO₂/HZSM-5 was established to investigate the intensified degradation of dimethyl sulphide (DMS). The system targets optimisation of the reactive oxygen species (ROS) and photocatalytic degradation pathways without catalyst deactivation. TiO₂/HZSM-5, containing highly dispersed TiO₂ nanoparticles, was prepared through the sol-gel method. TiO₂/HZSM-5 exhibits strong acidity and can adsorb DMS in multiple adsorption forms. Thus, the adsorption capacity of TiO₂/HZSM-5 is 20 and 53 times higher than that of Aeroxide TiO₂ (P25) in dry and highly humid air, respectively. UV-Vis analysis was performed to investigate the ROS in the gas phase. The results show that the concentrations of the ROS increased by 8% and 62.7% in dry and highly humid air, respectively. ¹O₂ and O (¹D), as well as ·OH are the major ROS, accounting for 73.6% and 61.6% in dry and highly humid air, respectively. A total of 92.5% DMS was removed over 600 min in dry air. Microwaves have strong desorption effects on absorbed substances, promoting the degradation of DMS via ROS in the gas phase. Moreover, ¹O₂, O (¹D), and ·OH can mineralise more DMS molecules into SO₂ and SO₃ through methanesulfonic acid. The highest mineralisation rate of 89.48% was obtained at 90% humidity over 600 min without catalyst deactivation. Therefore, this integrated system induced by microwave radiation can improve ROS production and prevent catalyst deactivation, providing an alternative to achieve higher photocatalytic performances in dry and highly humid air.

Isolation Strategy towards Earth-Abundant Single-Site Co-Catalysts for Photocatalytic Hydrogen Evolution Reaction

Achieving efficient photocatalytic water splitting remains one of the most vital challenges in the photocatalysis field, as the performance of contemporary heterogeneous catalysts is still limited by their insufficient activity and low predictability. To address this challenge, this work takes inspiration from the concept of heterogeneous single-metal-site catalysts (HSMSCs) and follows the idea of site-isolation, aiming towards single-site co-catalyst species and a higher atom-utilization efficiency. We synthesized a set of photocatalysts through an adsorption-limited wet impregnation process using bare and phosphate-modified TiO2 as model supports and earth-abundant metals (Cu and Ni) with various loadings (0.008–5 wt.%) as co-catalyst species. The catalysts are characterized by TXRF for the determination of the real co-catalyst loadings, UV-vis and FTIR spectroscopes for semi-quantitative analysis of the metal state and binding modes to the substrate, and HRTEM for resolving the morphology of the sample’s surface. All samples were then evaluated towards the photocatalytic hydrogen evolution reaction (HER). We show that much higher turnover frequencies (TOFs) are obtained for both Cu- and Ni-based systems when lower co-catalyst loadings are used, which indicates an improved atom-utilization efficiency that reaches performances comparable to the noble Au co-catalyst. We also introduce a structural model to explain the observed TOF trends, which confirms that both earth-abundant systems undergo a strong structural reconstruction upon site-isolation towards smaller, perhaps even single-site-like species.

A High-Efficiency Hematite Photoanode with Enhanced Bonding Energy Around Fe Atoms

Hematite nanoarrays are important photoanode materials. However, they suffer from serious problems of charge transfer and surface states; in particular, the surface states hinder the increase in photocurrent. A previous strategy to suppress the surface state is the deposition of an Fe-free metal oxide overlayer. Herein, from the viewpoint of atomic bonding energy, it is found that the strength of bonding around Fe atoms in the hematite is the key to suppressing the surface states. By treating the surface of hematite with Se and NaBH₄ , the Fe₂ O₃ transforms to a double-layer nanostructure. In the outer layer, the Fe-O bonding is reinforced and the Fe-Se bonding is even stronger. Therefore, the surface states are inhibited and the increase in the photocurrent density becomes much faster. Besides, the treatment constructs a nanoscale p-n junction to promote the charge transfer. Improvements are achieved in onset potential (0.25 V shift) and in photocurrent density (5.8 times). This work pinpoints the key to suppressing the surface states and preparing a high-efficiency hematite nanoarray, and deepens our understanding of hematite photoanodes.

Synthesis and Characterization of Novel Green Hybrid Nanocomposites for Application as Proton Exchange Membranes in Direct Borohydride Fuel Cells

Organic–inorganic nanocomposite membranes for potential application in direct borohydride fuel cells (DBFCs) are formulated from sulfonated poly(vinyl alcohol) (SPVA) with the incorporation of (PO4-TiO2) and (SO4-TiO2) nanotubes as doping agents. The functionalization of PVA to SPVA was done by using a 4-sulfophthalic acid as an ionic crosslinker and sulfonating agent. Morphological and structural characterization by transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) confirmed the successful synthesis of the doping agents and their incorporation into the polymer. The influence of PO4-TiO2 and SO4-TiO2 doping and their content on the physicochemical properties of the nanocomposite membranes was evaluated. Swelling degree and water uptake gradually reduced to 7% and 13%, respectively, with increasing doping agent concentration. Ion exchange capacity and ionic conductivity of the membrane with 3 wt.% doping agents were raised 5 and 7 times, respectively, compared to the undoped one. The thermal and oxidative stability and tensile strength also increased with the doping content. Furthermore, lower borohydride permeability (0.32 × 10−6 cm2 s−1) was measured for the membranes with higher amount of inorganic doping agents when compared to the undoped membrane (0.71 × 10−5 cm2 s−1) and Nafion®117 (0.40 × 10−6 cm2 s−1). These results pave the way for a green, simple and low-cost approach for the development of composite membranes for practical DBFCs.

TiO2 as an interfacial-charge-transfer-bridge to construct eosin Y-mediated direct Z-scheme electron transfer over a Co9S8 quantum dot/TiO2 photocatalyst

A novel eosin Y-mediated Z-scheme Co₉S₈ QDs/TiO₂ photocatalytic system was constructed and a high AQE of 37.4% is obtained at 470 nm for 20%Co₉S₈/TiO₂ heterojunction.

Graphene decorated MoS2for eosin Y-sensitized hydrogen evolution from water under visible light

MoS₂was modified with graphene (G) by a simple hydrothermal method. The eosin Y sensitized G/MoS₂composite displays enhanced hydrogen evolution in terms of not only activity but also stability.

A DFT study of the effect of SO4 groups on the properties of TiO2 nanoparticles

We present a study of the optical, electronic, and structural properties of TiO₂ anatase-structured nanoparticles upon adsorption of SO₄ groups, which are always present on the surface of the particles during the sulfate manufacturing method. Structural and electronic properties were studied using the density functional theory method (DFT), and optical properties were obtained by time-dependent DFT. It was found that SO₄ groups alter both the geometric and electronic structure of TiO₂ nanoparticles and change the photoabsorption characteristics. In particular, we find that η²-O₂ type O-O moieties are formed due to the adsorption of 3 and 4SO₄ groups.

A new fabrication of AgX (X = Br, I)–TiO2 nanoparticles immobilized on polyacrylonitrile (PAN) nanofibers with high photocatalytic activity and renewable property

AgX–TiO₂/PAN (X = Br, I) photocatalyst was synthesized by the electrospinning technique, solvothermal synthesis, physical adsorption and gas/solid reaction.

A simple carbazole based sensitizer attached to a Nafion-coated-TiO2 photocatalyst: the impact of controlling parameters towards visible light driven H2 production

A close neighborhood of TiO₂, Nafion and sensitizer components developed by easy fabrication favors synergistic photon-to-hydrogen efficiency in photocatalytic H₂ evolution.

Enhancement of photocatalytic H2 evolution of eosin Y-sensitized reduced graphene oxide through a simple photoreaction

A graphene oxide (GO) solution was irradiated by a Xenon lamp to form reduced graphene oxide (RGO). After irradiation, the epoxy, the carbonyl and the hydroxy groups are gradually removed from GO, resulting in an increase of sp(2) π-conjugated domains and defect carbons with holes for the formed RGO. The RGO conductivity increases due to the restoration of sp(2) π-conjugated domains. The photocatalytic activity of EY-RGO/Pt for hydrogen evolution was investigated with eosin Y (EY) as a sensitizer of the RGO and Pt as a co-catalyst. When the irradiation time is increased from 0 to 24 h the activity rises, and then reaches a plateau. Under optimum conditions (pH 10.0, 5.0 × 10(-4) mol L(-1) EY, 10 μg mL(-1) RGO), the maximal apparent quantum yield (AQY) of EY-RGO24/Pt for hydrogen evolution rises up to 12.9% under visible light irradiation (λ ≥ 420 nm), and 23.4% under monochromatic light irradiation at 520 nm. Fluorescence spectra and transient absorption decay spectra of the EY-sensitized RGO confirm that the electron transfer ability of RGO increases with increasing irradiation time. The adsorption quantity of EY on the surface of RGO enhances, too. The two factors ultimately result in an enhancement of the photocatalytic hydrogen evolution over EY-RGO/Pt with increasing irradiation time. A possible mechanism is discussed.