Bioinspired All-Polyester Diblock Copolymers Made from Poly(pentadecalactone) and Poly(3-hydroxycinnamate): Synthesis and Polymer Film Properties

A bioinspired diblock copolymer was synthesized from pentadecalactone and 3-hydroxy cinnamic acid. Poly(pentadecalactone) (PPDL) with a molar mass of up to 43,000 g mol-1 was obtained by ring-opening polymerization initiated propargyl alcohol. Poly(3-hydroxy cinnamate) (P3HCA) was obtained by polycondensation and end-functionalized with 3-azido propanol. The two functionalized homopolymers were connected via 1,3-dipolar Huisgen addition to yield the block copolymer PPDL-triazole-P3HCA. The structure the block copolymer was confirmed by proton NMR, FTIR spectroscopy and GPC. By analyzing the morphology of polymer films made from the homopolymers, from a 1:1 homopolymer blend, and from the PPDL-triazole-P3HCA block copolymer, clearly distinct micro- and nanostructures were revealed. Quantitative nanomechanical measurements revealed that the block copolymer PPDL-triazole-P3HCA had a DMT modulus of 22.3 ± 2.7 MPa, which was lower than that of the PPDL homopolymer (801 ± 42 MPa), yet significantly higher than that of the P3HCA homopolymer (1.77 ± 0.63 MPa). Thermal analytics showed that the melting point of PPDL-triazole-P3HCA was similar to PPDL (89-90 °C), while it had a glass transition was similar to P3HCA (123-124 °C). Thus, the semicrystalline, potentially degradable all-polyester block copolymer PPDL-triazole-P3HCA combines the thermal properties of either homopolymer, and has an intermediate elastic modulus.

In situ synthesis of poly(ether ester) via direct polycondensation of terephthalic acid and 1,3-propanediol with sulfonic acids as catalysts

Sulfonic acid-comprising catalysts were explored to in situ fabricate ether segments in the process of esterification of terephthalic acid and 1,3-propanediol, and developing a new pathway of poly(ether ester)s synthesis without the addition of oligoether as starting materials.

Analysis of individual block length of amphiphilic di- & tri-block copolymers containing poly(ethylene oxide) and poly(methyl methacrylate)

Estimation of individual block lengths and extent of homopolymers.

Photodegradation behavior and mechanism of poly(ethylene glycol-co-1,4-cyclohexanedimethanol terephthalate) (PETG) random copolymers: correlation with copolymer composition

Norrish type I and II mechanisms occurred in PETG copolymers. The inherent photostability of PETG decreased with increasing CHDM content. The higher CHDM content resulted in the higher crosslinking degree.

Incorporation of 1,4-cyclohexanedicarboxylic acid into poly(butylene terephthalate)-b-poly(tetramethylene glycol) to alter thermal properties without compromising tensile and elastic properties

Incorporation of 1,4-cyclohexanedicarboxylic acid to partially replace terephthalic acid results in a thermoplastic elastomer with decreased melting temperature and increased thermal stability while tensile and elastic properties remain unchanged.

Poly(ethylene glycol-co-1,4-cyclohexanedimethanol terephthalate) random copolymers: effect of copolymer composition and microstructure on the thermal properties and crystallization behavior

The glass transition temperature of the statistically random PETG copolymers increased linearly with the increasing CT content. An increase in the average sequence length resulted in a higher melting temperature.