Monolithic stationary phases prepared via cyclic anhydride ring-opening polymerization as tunable platforms for chromatographic applications

Polymer monolithic stationary phases were prepared based on a cyclic anhydride as a reactive and tunable platform via ring-opening post-polymerization using primary amines, octadecylamine and benzylamine. The characterization techniques indicated the insertion of the functional groups into the original monoliths and confirmed the amidation reactions. The post-polymerization modification also improved the monolith's thermal and mechanical stability and induced significant improvement in their surface area. The stationary phases were synthesized inside small dimension stainless-steel columns (2.1 mm i.d. × 50 mm length). The prepared columns before and after modifications have been tested for the separation of the alkylbenzene series and some polycyclic aromatic hydrocarbons (PAHs) as model compounds. In all cases, the chromatographic performance in terms of the height equivalent to a theoretical plate on the functionalized monoliths was remarkably improved when compared with that on the unmodified monolith, which was between 9.59-39.49 μm and 4.08-31.50 μm using monoliths modified with octadecylamine and benzylamine, respectively. Under the same chromatographic conditions, the functionalization of monoliths with octadecylamine provided more hydrophobic interactions and enhanced the retention of alkylbenzenes, while the modification of monoliths with benzyl groups improved the separation and the retention of the PAHs through the strong π-π interactions. However, post-modification polymerization with octadecylamine and benzylamine enhanced the separation efficiency of the prepared columns toward all studied compounds. The repeatability of the injections on the same column and the reproducibility of the prepared columns have been studied for some selected parameters and estimated in terms of percent relative standard deviation (%RSD) for some of the studied compounds. The repeatability of the prepared columns was ≤9.42% (n = 5) based on run-to-run injections and ≤9.48% based on day-to-day injections for five successive days. The reproducibility levels, on the other hand, were ≤20.95% for all studied parameters in all cases. To assess their performance for the analysis of real samples, the applicability of the prepared columns was examined for the separation of the active ingredients extracted from some commercial pharmaceutical formulations and for the separation of tea water extract constituents. The validation data show the suitability of the columns for practical use in the routine analysis of these samples.

A high-efficient nano pesticide-fertilizer combination fabricated by amino acid-modified cellulose based carriers

BACKGROUND

As the global population grows, large quantities of agrochemicals are used to secure food demand and there is an urgent need to develop efficient and environmentally friendly pesticides and fertilizers. Compared with traditional pesticides, nanopesticide formulations can achieve better foliar wettability, chemical stability, and water dispersibility without or with the minimal use of organic solvents, in line with the development of sustainable agriculture.

RESULTS

In this research, glycidyl methacrylate (GMA) was used as an intermediate and glycine methyl ester (GLY) was used as an organic nitrogen source to modify carboxymethyl cellulose (CMC) to synthesize a pesticide nanocarrier CMC-PGMA-GLY. A nanopesticide EB@CMC-PGMA-GLY (EB@CPG) was formed by the hydrophobic and electrostatic interactions of emamectin benzoate (EB), which had good water dispersion. The good affinity of the composite towards leaves led to the effective moistening of the leaf surface by the pesticide and through the pH control pesticide release. Biological experiments show that nanopesticides can maintain high insecticidal activity and have no toxicity to seed germination. The results of pot experiment showed that the nanocarriers could be used as an organic nitrogen fertilizer to increase the fresh weight of plants by 39.77%.

CONCLUSIONS

This environmentally friendly pesticide carrier can be used as a fertilizer to provide sufficient nutrients for crops, opening a new method for the development of sustainable agriculture. © 2021 Society of Chemical Industry.

Synthesis and Characterization of Redox-Responsive Disulfide Cross-Linked Polymer Particles for Energy Storage Applications

Cross-linking poly(glycidyl methacrylate) microparticles with redox-responsive bis(5-amino-l,3,4-thiadiazol-2-yl) disulfide moieties yield redox-active particles (RAPs) capable of electrochemical energy storage via a reversible 2-electron reduction of the disulfide bond. The resulting RAPs show improved electrochemical reversibility compared to a small-molecule disulfide analogue in solution, attributed to spatial confinement of the polymer-grafted disulfides in the particle. Galvanostatic cycling was used to investigate the impact of electrolyte selection on stability and specific capacity. A dimethyl sulfoxide/magnesium triflate electrolyte was ultimately selected for its favorable electrochemical reversibility and specific capacity. Additionally, the specific capacity showed a strong dependence on particle size where smaller particles yielded higher specific capacity. Overall, these experiments offer a promising direction in designing synthetically facile and electrochemically stable materials for organosulfur-based multielectron energy storage coupled with beyond Li ion systems such as Mg.

Thiol-Affinity Immobilization of Casein-Coated Silver Nanoparticles on Polymeric Membranes for Biofouling Control

Silver nanoparticles (AgNPs) have been widely studied for the control of biofouling on polymeric membranes due to their antimicrobial properties. However, nanoparticle leaching has posed a significant impediment against their widespread use. In this study, a one-step method of chemically embedding AgNPs on cellulose acetate (CA) membranes via their affinity to thiol group chemistry was investigated. The operational efficiency of the membranes was then determined via filtration and biofouling experiments. During filtration study, the average flux values of pure CA membranes was determined to be 11 ± 2 L/(m2·hr) (LMH), while membranes embedded with AgNPs showed significant increases in flux to 18 ± 2 LMH and 25 ± 9 LMH, with increasing amounts of AgNPs added, which is likely due to the NPs acting as pore formers. Leaching studies, performed both in dead-end and crossflow filtration, showed approximately 0.16 mg/L leaching of AgNPs after the first day of filtration, but afterwards the remaining chemically-attached AgNPs did not leach. Over 97% of AgNPs remained on the membranes after seven days of crossflow leaching filtration studies. Serratia marcescens were then used as target microorganisms in biofouling studies. It was observed that membranes embedded with AgNPs effectively suppressed the growth of Serratia marcescens, and specifically, membranes with AgNPs displayed a decrease in microbial growth by 59% and 99% as the amount of AgNP increased.

A simple and versatile route to amphiphilic polymethacrylates: catalytic chain transfer polymerisation (CCTP) coupled with post-polymerisation modifications

Amphiphilic polymers have become key figures in the fields of pharmacology, medicine, agriculture and cosmetics.

Polyampholytic graft copolymers based on polydehydroalanine (PDha) – synthesis, solution behavior and application as dispersants for carbon nanotubes

We herein introduce a versatile platform of graft copolymers featuring a polyampholytic backbone and side chains of varying length and polarity using post-polymerization modification of polydehydroalanine (PDha).

Toward Sulfur-Free RAFT Polymerization Induced Self-Assembly

Polymerization induced self-assembly (PISA) using methacrylate-based macromonomers as RAFT agents is an unexplored, attractive route to make self-assembled colloidal objects. The use of this class of RAFT-agents in heterogeneous polymerizations is however not trivial, because of their inherent low reactivity. In this work we demonstrate that two obstacles need to be overcome, one being control of chain-growth (propagation), the other monomer partitioning. Batch dispersion polymerizations of hydroxypropyl methacrylate in the presence of poly(glycerol methacrylate) macromonomers in water showed limited control of chain-growth. Semicontinuous experiments whereby monomer was fed improved results only to some extent. Control of propagation is essential for PISA to allow for dynamic rearrangement of colloidal structures. We tackled the problem of monomer partitioning (caused by uncontrolled particle nucleation) by starting the polymerization with an amphiphilic thermoresponsive diblock copolymer, already "phase-separated" from solution. TEM analysis showed that PISA was successful and that different particle morphologies were obtained throughout the polymerization.

Investigation and Demonstration of Catalyst/Initiator-Driven Selectivity in Thiol-Michael Reactions

Thiol-Michael "click" reactions are essential synthetic tools in the preparation of various materials including polymers, dendrimers, and other macromolecules. Despite increasing efforts to apply thiol-Michael chemistry in a controlled fashion, the selectivity of base- or nucleophile-promoted thiol-Michael reactions in complex mixtures of multiple thiols and/or acceptors remains largely unknown. Herein, we report a thorough fundamental study of the selectivity of thiol-Michael reactions through a series of 270 ternary reactions using ¹H NMR spectroscopy to quantify product selectivity. The varying influences of different catalysts/initiators are explored using ternary reactions between two Michael acceptors and a single thiol or between a single Michael acceptor and two thiols using three different catalysts/initiators (triethylamine, DBU, and dimethylphenylphosphine) in chloroform. The results from the ternary reactions provide a platform from which sequential quaternary, one-pot quaternary, and sequential senary thiol-Michael reactions were designed and their selectivities quantified. These results provide insights into the design of selective thiol-Michael reactions that can be used for the synthesis and functionalization of multicomponent polymers and further informs how catalyst/initiator choice influences the reactivity between a given thiol and Michael acceptor.

Post-polymerization modification reactions of poly(glycidyl methacrylate)s

Single and multiple post-polymerization modifications of poly(glycidyl methacrylate) scaffold through the nucleophilic ring-opening reactions of the pendent epoxide groups are described.

Addressing the mid-point of polymer chains for multiple functionalization purposes through sequential thiol–epoxy ‘click’ and esterification reactions

A synthetic strategy is devised for the preparation of mid-chain multifunctional polymers.

Synthesis and post-polymerisation modification of an epoxy-functional polycarbonate

The synthesis and post-polymerisation functionalisation of an epoxide-functional polycarbonate via the selective carbonate ring-opening polymerisation (ROP) of trimethylenepropane oxirane ether carbonate (TMOC) monomer was investigated using a range of organocatalysts.

Homopolymer bifunctionalization through sequential thiol–epoxy and esterification reactions: an optimization, quantification, and structural elucidation study

In this study, we probe various aspects of a post-polymerization double-modification strategy involving sequential thiol–epoxy and esterification reactions for the preparation of dual-functional homopolymers.

Thiol–ene “click” reactions and recent applications in polymer and materials synthesis: a first update

This contribution serves as an update to a previous review (Polym. Chem.2010,1, 17–36) and highlights recent applications of thiol–ene ‘click’ chemistry as an efficient tool for both polymer/materials synthesis as well as modification.

Multiblock sequence-controlled glycopolymers via Cu(0)-LRP following efficient thiol–halogen, thiol–epoxy and CuAAC reactions

The combination of copper(0) mediated living radical polymerization (Cu(0)-LRP) with thiol–halogen, thiol–epoxy and copper catalysed alkyne azide coupling (CuAAC) click chemistry has been employed to give a new route to multiblock sequence-controlled glycopolymers.