A sustainable one-pot method to transform seashell waste calcium carbonate to osteoinductive hydroxyapatite micro-nanoparticles

We have developed a straightforward, one-pot, low-temperature hydrothermal method to transform oyster shell waste particles (bCCP) from the species Crassostrea gigas (Mg-calcite, 5 wt% Mg) into hydroxyapatite (HA) micro/nanoparticles. The influence of the P reagents (H3PO4, KH2PO4, and K2HPO4), P/bCCP molar ratios (0.24, 0.6, and 0.96), digestion temperatures (25-200 °C), and digestion times (1 week-2 months) on the transformation process was thoroughly investigated. At 1 week, the minimum temperature to yield the full transformation significantly reduced from 160 °C to 120 °C when using K2HPO4 instead of KH2PO4 at a P/bCCP ratio of 0.6, and even to 80 °C at a P/bCCP ratio of 0.96. The transformation took place via a dissolution-reprecipitation mechanism driven by the favorable balance between HA precipitation and bCCP dissolution, due to the lower solubility product of HA than that of calcite at any of the tested temperatures. Both the bCCP and the derived HA particles were cytocompatible for MG-63 human osteosarcoma cells and m17.ASC murine mesenchymal stem cells, and additionally, they promoted the osteogenic differentiation of m17.ASC, especially the HA particles. Because of their physicochemical features and biological compatibility, both particles could be useful osteoinductive platforms for translational applications in bone tissue engineering.

Zinc- and magnesium-doped hydroxyapatite-urea nanohybrids enhance wheat growth and nitrogen uptake

The ongoing and unrestrained application of nitrogen fertilizer to agricultural lands has been directly linked to climate change and reductions in biodiversity. The agricultural sector needs a technological upgrade to adopt sustainable methods for maintaining high yield. We report synthesis of zinc and magnesium doped and undoped hydroxyapatite nanoparticles, and their urea nanohybrids, to sustainably deliver nitrogen to wheat. The urea nanohybrids loaded with up to 42% nitrogen were used as a new source of nitrogen and compared with a conventional urea-based fertilizer for efficient and sufficient nitrogen delivery to pot-grown wheat. Doping with zinc and magnesium manipulated the hydroxyapatite crystallinity for smaller size and higher nitrogen loading capacity. Interestingly, 50% and 25% doses of urea nanohybrids significantly boosted the wheat growth and yield compared with 100% doses of urea fertilizer. In addition, the nutritional elements uptake and grain protein and phospholipid levels were significantly enhanced in wheat treated with nanohybrids. These results demonstrate the potential of the multi-nutrient complexes, the zinc and magnesium doped and undoped hydroxyapatite-urea nanoparticles, as nitrogen delivery agents that reduce nitrogen inputs by at least 50% while maintaining wheat plant growth and nitrogen uptake to the same level as full-dose urea treatments.

Synthesis of Ce/Gd@HA/PLGA Scaffolds Contributing to Bone Repair and MRI Enhancement

It is important for future clinical applications to design and synthesize multipurpose scaffolding materials for bone tissue engineering with high osteogenic induction and MRI capability. In the present study, we synthesized Ce/Gd@HA by co-doping Ce3+ and Gd3+ into hydroxyapatite (HA) using a hydrothermal synthesis method, and then Ce/Gd@HA composites were synthesized by combining Ce/Gd@HA nanoparticles with polylactic-co-glycolic acid (PLGA) to investigate whether implanted Ce/Gd@HA/PLGA composites could promote osteoblast viability, leading to tibia repair of the rats and enhance MRI. The measurement results contain X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, and environmental scanning electron microscopy (ESEM) showing that HA doped with Ce3+ and Gd3+ was still a hexagonal crystal with high crystallinity. The synthesized Ce/Gd@HA/PLGA composites have a structure and obvious magnetic resonance imaging (MRI) capability. The in vitro experimental results indicated that Ce/Gd@HA/PLGA composites significantly promoted the performance of MC3T3-E1 cells, containing proliferation, adhesion, and osteogenic differentiation capacities. These include the improvement of alkaline phosphatase activity, enhancement of mineral deposition, and upregulation of OCN and COL-1 gene expression. The in vivo experimental results demonstrated that the Ce/Gd@HA/PLGA composites significantly improved the healing rate of rat bone defects. The MRI images indicated that the Ga-doped composites were observed in the MRI T1 sequence in rats. The aforementioned results suggested that Ce/Gd@HA/PLGA composites not only effectively promoted bone formation but also enhanced MRI capability. The composites synthesized in this study have great potential in bone regeneration with an extensive application in bone tissue engineering.

Preparation and Characterization of Mg-Doped Calcium Phosphate-Coated Phycocyanin Nanoparticles for Improving the Thermal Stability of Phycocyanin

Phycocyanin (PC) is a blue-colored, pigment-protein complex with unique fluorescence characteristics. However, heat leads to PC fading and fluorescence decay, hampering its widespread application. To improve the thermal stability of PC, we induced the in situ mineralization of calcium phosphate (CaP) on the PC surface to prepare PC@Mg-CaP. The nanoparticles were characterized using transmission electron microscopy, energy dispersive spectrometry, fourier transform infrared spectroscopy, and X-ray diffraction. The results showed that PC@Mg-CaP was spherical, and the nanoparticle size was less than 200 nm. The shell of PC@Mg-CaP was composed of amorphous calcium phosphate (ACP). The study suggested that CaP mineralization significantly improved the thermal stability of PC. After heating at 70 °C for 30 min, the relative concentration of PC@Mg-CaP with a Ca/P ratio = 2 was 5.31 times higher than that of PC. Furthermore, the Ca/P ratio was a critical factor for the thermal stability of PC@Mg-CaP. With decreasing Ca/P, the particle size and thermal stability of PC@Mg-CaP significantly increased. This work could provide a feasible approach for the application of PC and other thermal-sensitive biomolecules in functional foods requiring heat treatment.

Ba/Mg co-doped hydroxyapatite/PLGA composites enhance X-ray imaging and bone defect regeneration

Hydroxyapatite (HA) is the most commonly used orthopedic implant material. In recent years, the emergence of cationic doped hydroxyapatite has revealed more possibilities for the biological application of HA. Conventional HA does not promote new bone formation because of its poor osteoinductive activity, and has a similar density to that of bone, leading to difficulty in distinguishing both via imaging. Magnesium ions are useful for regulating the cellular behavior and promoting bone regeneration. Ba ion related compounds, such as BaSO₄, have a strong X-ray shielding effect. In this study, Ba/Mg@HA was synthesized to prepare Ba/Mg@HA/PLGA composites, and we aimed to investigate if Ba/Mg@HA/PLGA composites enhanced bone repair on osteoblasts and tibial defects, as well as the X-ray and CT imaging ability of bone implants in rats. The in vitro experimental results showed that the Ba/Mg@HA/PLGA composites significantly improved the attachment and osteogenic differentiation of MC3T3-E1 cells. These include the promotion of mineral deposition, enhancement of alkaline phosphatase activity, upregulation of OCN and COL-1 gene expression, and increase in COL-1 and OCN protein expression in a time- and concentration-dependent manner. The in vivo experimental results showed that the Ba/Mg@HA/PLGA composites significantly increased the rate of bone defect healing and the expression of BMP-2 and COL-1 in the bones of rats. X-ray and CT imaging results showed that the Ba/Mg@HA/PLGA composites enhanced the X-ray imaging ability. These findings indicate that the Ba/Mg@HA/PLGA composites can effectively promote bone formation and improve the X-ray and CT imaging abilities to a certain extent.

PCL-Coated Multi-Substituted Calcium Phosphate Bone Scaffolds with Enhanced Properties

Ionic substitutions within the hydroxyapatite lattice are a widely used approach to mimic the chemical composition of the bone mineral. In this work, Sr-substituted and Mg- and Sr-co-substituted calcium phosphate (CaP) scaffolds, with various levels of strontium and magnesium substitution, were prepared using the hydrothermal method at 200 °C. Calcium carbonate skeletons of cuttlefish bone, ammonium dihydrogenphosphate (NH₄H₂PO₄), strontium nitrate (Sr(NO₃)₂), and magnesium perchlorate (Mg(ClO₄)₂) were used as reagents. Materials were characterized by means of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Whole powder pattern decomposition refinements of XRD data indicated that increased magnesium content in the Mg- and Sr-co-substituted scaffolds was related to an increased proportion of the whitlockite (WH) phase in the biphasic hydroxyapatite (HAp)/WH scaffolds. In addition, refinements indicate that Sr²⁺ ions have replaced Ca²⁺ sites in the WH phase. Furthermore, PCL-coated Mg-substituted and Sr- and Mg-co-substituted scaffolds, with the HAp:WH wt. ratio of 90:10 were prepared by vacuum impregnation. Results of compression tests showed a positive impact of the WH phase and PCL coating on the mechanical properties of scaffolds. Human mesenchymal stem cells (hMSCs) were cultured on composite scaffolds in an osteogenic medium for 21 days. Immunohistochemical staining showed that Mg-Sr-CaP/PCL scaffold exhibited higher expression of collagen type I than the Mg-CaP/PCL scaffold, indicating the positive effect of Sr²⁺ ions on the differentiation of hMSCs, in concordance with histology results. Reverse transcription-quantitative polymerase chain reaction (RT-qPCR) analysis confirmed an early stage of osteogenic differentiation.

Silver-hydroxyapatite nanocomposites prepared by three sequential reaction steps in one pot and their bioactivities in vitro

Hydroxyapatite (HA) combined with antimicrobial agents for biomedical application can effectively avoid the bacteria infection, while HA have the good performance. In this study, we prepared silver-hydroxyapatite (Ag-HA) nanocomposites using a one-pot method consisting of three sequential steps of wet chemical precipitation, ion exchange, and a silver mirror reaction. The HA nanoparticles used as the precursor for Ag ion doping were first synthesised by wet chemical precipitation. Next, Ag⁺ absorbed on HA surface through ion exchange reaction. Glucose was then added to initiate the silver mirror reaction, which made the Ag⁺ ions reduce to Ag⁰ and Ag nanoparticles in situ formed on HA nanoparticles. Subsequently, Ag-HA nanocomposites with different Ag content were prepared. X-ray diffraction, SEM, EDX mapping and TEM imaging confirmed that spherical Ag nanoparticles ~20-40 nm in diameter were adhered to the surface of HA nano-rods (0.4-0.8 μm in length and 15-40 nm in diameter). The Ag content (1.9-15.2 wt%) in the Ag-HA nanocomposites was adjusted by varying the feeding Ag/Ca molar ratio (2.0-20%). The cell viability evaluation in vitro proved that Ag-HA nanocomposites had low cytotoxicity to L929 normal cells. Meanwhile, the antibacterial examinations in vitro demonstrated that Ag-HA nanocomposites had obvious antibacterial effects on Gram-positive bacteria, Gram-negative bacteria, and fungus. The antibacterial results were dose-dependent on the accumulation of silver content. The Ag-HA nanocomposites loaded PMMA resins also demonstrated a potential antibacterial activity against S. mutans. This paper presents a convenient and bio-friendly approach for preparing Ag-HA nanocomposites with adjustable Ag content, which are a promising material for biomedical applications.

Removal of Cadmium (II), Chromium (III), and Lead (II) Heavy Metal Ions from Water by Graft Copolymerization of Acrylonitrile onto Date Palm Fiber Using H2O2/Fe++ as an Initiator

The study is aimed at assessing how the date palm wood fibers (DPWF) can be used for the removal of heavy metals from water. The study involved examination of the radical polymerization and graft polymerization parameters such as reaction period, reaction time, monomer volume, amount of the catalyst, and concentration of initiator to obtain the maximum yield of graft polymerization. Fiber and copolymer were characterized using SEM and FT-IR spectroscopy to ensure the completion of polymerization. Hydroxylamine hydrochloride was used for treating the grafted copolymers for the preparation of polyamidoxime chelating resin, which was then examined for removing the heavy metal ions. Different resin dosages, contact time, and initial concentrations were used, and the batch technique experiment was utilized. The study also applied the Langmuir and Freundlich isotherm model, and Langmuir was found to be better. The absorption ability was found to be better for polyamidoxime resin for metal ions of cadmium (II), chromium (III), and lead (II).

Synthesis of Magnesium- and Silicon-modified Hydroxyapatites by Microwave-Assisted Method

Nanopowders of hydroxyapatite (HA), modified by magnesium (MgHA) and by silicon (SiHA) were obtained by liquid-phase microwave synthesis method. X-ray diffraction and IR spectroscopy results showed that Mg2+ and SiO44- ions were present in the synthesized products both as secondary phases and as part of the HA phase. Whitlockite was found in the magnesium-modified HA (MgHA) and larnite was found in the silicon-modified HA (SiHA); ion substitution for both materials resulted in solid solutions. In the synthesized samples of modified HA, the increase of particle size of powders was in the order HA < SiHA < MgHA, which was calculated through data specific surface area and measured pycnometric density of the powders. The Lewis acid sites (Ca2+, Mg2+, Si4+) were present using spectral probes on the surface of the samples of HA, MgHA, and SiHA, and the acidity of these sites decreased in the order SiHA > MgHA > HA. The rates of calcium phosphate layer deposition on the surface of these materials at 37 °C in the model simulated body fluid solution showed similar dependence.

Bio-inspired synthesis of aqueous nanoapatite liquid crystals

The macroscopically ordered structure of rod-like nanoapatites within the collagen matrix is of great significance for the mechanical performance of bones and teeth. However, the synthesis of macroscopically ordered nanoapatite remains a challenge. Inspired by the effect of citrate molecules on apatite crystals in natural bone and the similarities between these ordered rod-like nanoapatites and the nematic phase of inorganic liquid crystals (LCs), we synthesized aqueous liquid crystal from rod-like nanoapatites with the aid of sodium citrate. Following a similar procedure, aqueous Mg(OH)2 and Mg3(PO4)2 LCs were also prepared. These findings lay the foundation for the fabrication of macroscopically assembled nanoapatite-based functional materials for biomedical applications and offer a green chemical synthesis platform for the development of new types of inorganic LCs. This process may reduce the difficulties in synthesizing large quantities of inorganic LCs so that they can be applied to the fabrication of functional materials.

Effects of ultrasonic agitation time on wet chemical synthesis of nanohydroxyapatite

In this study, the synthesis of the nanohydroxyapatite (nHAp) powders by way of wet chemical method is reported. Calcium nitrate tetrahydrate (Ca(NO3)2·H2O) and dibasic ammonium phosphate ((NH4)2HPO4) were used as calcium and phosphorus sources, respectively. The effect of ultrasonic agitation time has been systematically studied between 30 and 150 min at the temperature of 70°C. Structural, morphological, spectroscopic and thermal analysis have been carried out by way of X-ray powder diffraction, scanning electron microscopy, Fourier-transform infrared spectroscopy and Raman spectroscopy and thermogravimetry–differential scanning calorimetry analysis. It is shown that the ultrasonic agitation conditions significantly affect the crystallite size, dislocation density and microstrain of the powders calculated by way of the Debye–Scherrer formula. Thermal analyses reveal that the ultrasonic agitation treatment has a very beneficial effect on the fabrication of the powders by the wet chemical method due to the inhibition of physisorbed and chemisorbed water and the calcium deficiency. Magnetic stirring treatment is found to lead to larger nHAp nanoparticle agglomerations due to more water absorption. The results offer a promising route towards the scalable synthesis of the pure-phase nHAp powders with controllable structural and morphological properties, which could be useful in various types of basic and applied research on HAp-based materials.

Fluorination Enhances the Osteogenic Capacity of Porcine Hydroxyapatite

In a previous study, we successfully prepared fluorinated porcine hydroxyapatite (FPHA) by immersing porcine hydroxyapatite (PHA) in an aqueous solution of 0.25 M sodium fluoride (NaF) under thermal treatment, and the resulting FPHA showed better physicochemical and biological properties than PHA. The purpose of this study was to further investigate how fluorine incorporation influenced the biocompatibility and osteogenic capacity of PHA. The concentrations of Ca, P, F, and Mg ions in PHA and FPHA extracts were detected by inductively coupled plasma optical emission spectrometry. Rat bone marrow stromal cells (rBMSCs) were treated with PHA and FPHA extracts, and the effects of these extracts on cell proliferation and osteoblastic differentiation were evaluated via Cell Counting Kit-8 assay, alkaline phosphatase assay, and real time-quantitative polymerase chain reaction. For the in vivo assessment, PHA and FPHA were implanted into subcutaneous pockets (n = 6) and rat calvarial defects (diameter = 5 mm, n = 14) for 12 weeks to determine their biocompatibility and osteogenic capacity by using micro-computed tomography (CT) and histological analysis. FPHA extracts, which release higher concentrations of F and Mg ions, better promoted the osteoblastic differentiation of rBMSCs in vitro. The result of biocompatibility evaluation confirmed that the host response and chronic inflammation cells infiltration degree around PHA and FPHA granules were similar. Micro-CT and histological analysis showed newer mineralized bone formation in rats with FPHA-treated defects than in rats with PHA-treated defects. The results of in vitro and in vivo tests consistently indicate that fluorine incorporation effectively enhanced the osteogenic capacity of PHA.

In-vitro biocompatibility, bioactivity and photoluminescence properties of Eu3+ /Sr2+ dual-doped nano-hydroxyapatite for biomedical applications

In the present investigation, we have successfully synthesized luminescent Eu³⁺ -doped and Eu³⁺ /Sr²⁺ codoped hydroxyapatite (HA) nanoparticles through sol-gel assisted precipitation method with the aim of developing novel biomaterials containing osteoblast mineral (Sr²⁺ ) and luminescence activator (Eu³⁺ ). The structure, morphology, thermal stability, and luminescence properties of the resultant spherical nanoparticles (50-100 nm diameters) were studied. Moreover, the in-vitro bioactivity of Eu_0.1 Sr_0.1 HA nanoparticles was investigated by immersing in the simulated body fluid for many weeks. The antimicrobial activity results against gram positive and gram negative bacterial stains, showed better resistivity for the Eu_0.1 Sr_0.1 HA among the other compositions. The MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] assay of live/dead cells cultured with Eu³⁺ /Sr²⁺ -doped HA nanoparticles retained its normal morphology and did not show a significant impact on cell proliferation at various incubation days, which evidence for the material's superior biocompatible nature even at a higher concentration of 375 µg/mL. Thus, the incorporation of dual ions in HA nanoparticles with strong luminescence properties develops potential biomaterial for live cell imaging and in nanomedicine. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 2191-2201, 2018.

Hydroxyapatite coatings with oriented nanoplate arrays: synthesis, formation mechanism and cytocompatibility

A novel strategy has been developed to fabricate hydroxyapatite coatings with oriented nanoplate arrays for implants of human hard tissues.

Redox-responsive nanoreservoirs based on collagen end-capped mesoporous hydroxyapatite nanoparticles for targeted drug delivery

Schematic illustration of a redox-responsive system based on collagen-capped MHAp for cell-targeted drug delivery.