Preparation, characterization, and properties of PMMA-doped polymer film materials: a study on the effect of terbium ions on luminescence and lifetime enhancement

Polymer Doping as a Novel Approach to Improve the Performance of Plasmonic Plastic Optical Fibers Sensors

In this work, Fe2O3 was investigated as a doping agent for poly(methyl methacrylate) (PMMA) in order to enhance the plasmonic effect in sensors based on D-shaped plastic optical fibers (POFs). The doping procedure consists of immerging a premanufactured POF sensor chip in an iron (III) solution, avoiding repolymerization and its related disadvantages. After treatment, a sputtering process was used to deposit a gold nanofilm on the doped PMMA in order to obtain the surface plasmon resonance (SPR). More specifically, the doping procedure increases the refractive index of the POF's PMMA in contact with the gold nanofilm, improving the SPR phenomena. The doping of the PMMA was characterized by different analyses in order to determine the effectiveness of the doping procedure. Moreover, experimental results obtained by exploiting different water-glycerin solutions have been used to test the different SPR responses. The achieved bulk sensitivities confirmed the improvement of the plasmonic phenomenon with respect to a similar sensor configuration based on a not-doped PMMA SPR-POF chip. Finally, doped and non-doped SPR-POF platforms were functionalized with a molecularly imprinted polymer (MIP), specific for the bovine serum albumin (BSA) detection, to obtain dose-response curves. These experimental results confirmed an increase in binding sensitivity for the doped PMMA sensor. Therefore, a lower limit of detection (LOD), equal to 0.04 μM, has been obtained in the case of the doped PMMA sensor when compared to the one calculated for the not-doped sensor configuration equal to about 0.09 μM.

Thermal, Spectroscopy and Luminescent Characterization of Hybrid PMMA/Lanthanide Complex Materials

Novel hybrid materials based on the poly(methyl methacrylate) (PMMA) matrix and lanthanide(III) carboxylates Eu:2,6-DClB and Tb:2,6-DClB were synthesized and carefully analyzed in the context of their potential application in optically active polymer-based optical fibers. To determine the usefulness of the obtained materials, a careful thermal, mass spectroscopy, and optical characterization was performed, focusing on the features critical for the technology of optical fiber processing. In addition, the luminescent features of both lanthanide complexes and the resulting hybrid composites were carefully investigated to identify the processes responsible for light emission and to analyze the influence of the PMMA host on light emission intensity and spectral characteristics. The obtained results showed that both lanthanide carboxylate complexes exhibited intense luminescence in the red and green spectral range, typical of europium and terbium dopants, and that those features were well preserved after introducing them into the PMMA polymer. Thermal analysis also proved that introducing the luminescent additives did not significantly affect the thermal properties of both hybrid materials, thus enabling further processing into the form of optical fibers.

Synthesis and characterization of poly(methyl methacrylate) co-doped with Tb(tmhd)3 - Rhodamine B for luminescent optical fiber applications

Currently, there is a growing interest in the development of multi-colored materials based on the combination of two or more systems (organic or inorganic) as a strategy to take advantage of their combined physical or chemical properties. These multi-colored materials have found potential applications as sensors, amplifiers, and optical fibers. In this work, the physical characteristics of poly(methyl methacrylate) (PMMA) doped with Terbium(III)-tris-(2,2,6,6-tetramethyl-3,5-heptanedionate) (Tb(tmhd)₃) at 1.57-1.58 mmol and Rhodamine B (RhB) at different concentrations were analyzed. The emission obtained from these samples (multichromophoric samples) varied as function of RhB concentration due to an efficient energy transfer process (33-65%). The role of PMMA as inert matrix that assists in the recombination process was confirmed by FTIR and Raman spectra analysis. Moreover, an improvement in thermal resistance of the materials was observed due to the presence of the dopants during the polymerization process.

Diarylethene-based conjugated polymer networks for ultrafast photochromic films

Two new diarylethene-based conjugated polymers were synthesized, and their films exhibited ultrafast photochromism properties and excellent fatigue resistance.

Smart composite films of nanometric thickness based on copper-iodine coordination polymers. Toward sensors

One-pot reactions between CuI and methyl or methyl 2-amino-isonicotinate give rise to the formation of two coordination polymers (CPs) based on double zig-zag Cu2I2 chains. The presence of a NH2 group in the isonicotinate ligand produces different supramolecular interactions affecting the Cu-Cu distances and symmetry of the Cu2I2 chains. These structural variations significantly modulate their physical properties. Thus, both CPs are semiconductors and also show reversible thermo/mechanoluminescence. X-ray diffraction studies carried out under different temperature and pressure conditions in combination with theoretical calculations have been used to rationalize the multi-stimuli-responsive properties. Importantly, a bottom-up procedure based on fast precipitation leads to nanofibers of both CPs. The dimensions of these nanofibres enable the preparation of thermo/mechanochromic film composites with polyvinylidene difluoride. These films are tens of nanometers in thickness while being centimeters in length, representing smaller thicknesses so far reported for thin-film composites. This nanomaterial integration of CPs could represent a source of alternative nanomaterials for opto-electronic device fabrication.

Silsesquioxane-based luminescent PMMA nanocomposites

Multimethacrylate functionalized cage silsesquioxane is a highly polymerizable monomer that can also act as a ligand coordinating agent to form luminescent hybrid complex with rare earth ions.

Dual functional fluorescent sensor for selectively detecting acetone and Fe3+ based on {Cu2N4} substructure bridged Cu(i) coordination polymer

A novel red emission polymer can serve as a dual functional fluorescent sensor for selectively detecting trace amounts of acetone and Fe³⁺ though quenching the luminescence.