One-Step Multifunctionalization of Flax Fabrics for Simultaneous Flame-Retardant and Hydro-Oleophobic Properties Using Radiation-Induced Graft Polymerization

This study concerns the one-step radiografting of flax fabrics with phosphonated and fluorinated polymer chains using (meth)acrylic monomers: dimethyl(methacryloxy)methyl phosphonate (MAPC1), 2-(perfluorobutyl)ethyl methacrylate (M4), 1H,1H,2H,2H-perfluorooctyl acrylate (AC6) and 1H,1H,2H,2H-perfluorodecyl methacrylate (M8). The multifunctionalization of flax fabrics using a pre-irradiation procedure at 20 and 100 kGy allows simultaneously providing them with flame retardancy and hydro- and oleophobicity properties. The successful grafting of flax fibers is first confirmed by FTIR spectroscopy. The morphology of the treated fabrics, the regioselectivity of grafting and the distribution of the fluorine and phosphorus elements are assessed by scanning electron microscopy (SEM) coupled with energy-dispersive X-ray spectroscopy (SEM-EDX). The flame retardancy is evaluated using pyrolysis combustion flow calorimetry (PCFC) and cone calorimetry. The hydro- and oleophobicity and water repellency of the treated fabrics is established by contact angle and sliding angle measurements, respectively. The grafting treatment of flax irradiated at 100 KGy, using M8 and MAPC1 monomers (50:50) for 24 h, allows achieving fluorine and phosphorus contents of 8.04 wt% and 0.77 wt%, respectively. The modified fabrics display excellent hydro-oleophobic and flame-retardant properties with water and diiodomethane contact angles of 151° and 131°, respectively, and a large decrease in peak of heat release rate (pHRR) compared to pristine flax (from 230 W/g to 53 W/g). Relevant results are also obtained for M4 and AC6 monomers in combination with MAPC1. For the flame retardancy feature, the presence of fluorinated groups does not disturb the effect of phosphorus.

Synthesis of a New Phosphonate-Based Sorbent and Characterization of Its Interactions with Lanthanum (III) and Terbium (III)

High-tech applications require increasing amounts of rare earth elements (REE). Their recovery from low-grade minerals and their recycling from secondary sources (as waste materials) are of critical importance. There is increasing attention paid to the development of new sorbents for REE recovery from dilute solutions. A new generation of composite sorbents based on brown algal biomass (alginate) and polyethylenimine (PEI) was recently developed (ALPEI hydrogel beads). The phosphorylation of the beads strongly improves the affinity of the sorbents for REEs (such as La and Tb): by 4.5 to 6.9 times compared with raw beads. The synthesis procedure (epicholorhydrin-activation, phosphorylation and de-esterification) is investigated by XPS and FTIR for characterizing the grafting route but also for interpreting the binding mechanism (contribution of N-bearing from PEI, O-bearing from alginate and P-bearing groups). Metal ions can be readily eluted using an acidic calcium chloride solution, which regenerates the sorbent: the FTIR spectra are hardly changed after five successive cycles of sorption and desorption. The materials are also characterized by elemental, textural and thermogravimetric analyses. The phosphorylation of ALPEI beads by this new method opens promising perspectives for the recovery of these strategic metals from mild acid solutions (i.e., pH ~ 4).

Monolayer doping of germanium by phosphorus-containing molecules

The DPP (diethyl 1-propylphosphonate) and ODPA (octadecylphosphonic acid) molecules are studied as precursors for the monolayer doping (MLD) of germanium. Their adsorption behaviour is investigated, revealing different physicochemical interactions between the phosphorus-containing molecules and the Ge surfaces. It is discovered that DPP adsorption occurs after the oxidation of Ge surface, while the ODPA undergoes chemisorption on -H terminated surfaces. Quantitative phosphorus analysis demonstrates that in the first case more than one monolayer is formed (from 2 to 4), while in the second a single monolayer is formed. Moreover, the analysis of phosphorus diffusion from the surface layers into the Ge matrix reveals that conventional thermal annealing processes are not suitable for Ge injection due to a higher activation energy of the process in comparison with silicon. On the contrary, pulsed laser melting is effective in forming a doped layer, owing to the precursor's decomposition under UV light.

Synthesis of new high molecular weight phosphorylated chitosans for improving corrosion protection

Two grades of chitosan [chitosan 30000 g mol−1 (N-chitosan 30) and 250000 g mol−1 (N-chitosan 250)] were functionalized by the Kabachnik–Fields reaction. To obtain the highest phosphonic ester grafting rate (55% and 40% for the N-chitosan 30 and N-chitosan 250, respectively), the pH must be kept constant during the reaction (pH=5). Then, a partial hydrolysis of the ester functions was carried out in HCl medium to generate phosphonic acid functions up to 25% and 20% for the N-chitosan 30 and N-chitosan 250, respectively. It was shown that the grafting of phosphonic acids on chitosan significantly reduced the dynamic viscosity. Afterwards, electrochemical impedance measurements were performed in an aqueous solution (pH=5) in the presence of either N-chitosans or P-chitosans (3 wt.%). The two native N-chitosans were little adsorbed onto the carbon steel surface and the corrosion protection was low. In contrast, the impedance results in the presence of the 30000 g mol−1 phosphorylated chitosan (P-chitosan 30) evidenced the beneficial effect of grafted phosphonic acid on its adsorption on the steel surface. The lower efficiency of the 250000 g mol−1 (P-chitosan 250) was attributed to its high molecular weight which made difficult the interactions between the phosphonic groups and the metallic surface.

An environmental application of functionalized chitosan: enhancement of the separation of the solid and liquid fractions of digestate from anaerobic digestion

A high molecular weight chitosan was chemically modified to quantitatively incorporate quaternary ammonium groups. Its efficiency was evaluated in the liquid-solid separation for various liquors, and compared with the one of a polyelectrolyte usually used for this utilization. The performance of the liquid-solid separation was estimated through the determination of two parameters measured after the screening- settling of the mixture liquor/flocculating agent: the separation efficiency (EV) and the TS removal efficiency (ETS). Apart for liquor 6, TS removal was always better after an addition of functionalized chitosan. Furthermore, whatever the type of liquor, the distribution was modified by an increased presence of high-size particles when functionalized chitosan was added. Moreover, chitosan addition tended to homogenize the size of the particles, which could facilitate the choice of the liquid-solid separation process. This homogenization was particularly observed for the liquor initially highly dispersed in size, i.e. liquors 1, 4, 6 and 8.

A Chitosan Derivative Containing Both Carboxylic Acid and Quaternary Ammonium Moieties for the Synthesis of Cyclic Carbonates

Chitosan, a renewable feedstock, is modified and used as a catalytic support in the presence of potassium iodide. The system is highly efficient towards the incorporation of carbon dioxide (CO2 ) into epoxides. It demonstrates very good thermal stability and is recyclable more than five times without loss of activity. The optimal reaction conditions were determined using allylglycidyl ether as a model and extended to a wide range of other epoxides. Cyclic carbonates were obtained with very high yield in a few hours under mild conditions (2-7 bar≈0.2-0.7 MPa, 80 °C) and no solvent.

A novel α-aminophosphonic acid-modified acrylamide-based hydrophobic associating copolymer with superb water solubility for enhanced oil recovery

Here we report a novel α-aminophosphonic acid-modified acrylamide-based hydrophobic associating copolymer. The copolymer exhibits significant potential as an enhanced oil recovery chemical for high-temperature and high-mineralization oilfields.

Enhancing the imaging and biosafety of upconversion nanoparticles through phosphonate coating

Upconversion nanoparticles (UCNPs), which are generated by doping with rare earth (RE) metals, are increasingly used for bioimaging because of the advantages they hold over conventional fluorophores. However, because pristine RE nanoparticles (NPs) are unstable in acidic physiological fluids (e.g., lysosomes), leading to intracellular phosphate complexation with the possibility of lysosomal injury, it is important to ensure that UCNPs are safely designed. In this study, we used commercially available NaYF4:Er/Yb UCNPs to study their stability in lysosomes and simulated lysosomal fluid. We demonstrate that phosphate complexation leads to REPO4 deposition on the particle surfaces and morphological transformation. This leads to a decline in upconversion fluorescence efficiency as well as inducing pro-inflammatory effects at the cellular level and in the intact lung. In order to preserve the imaging properties of the UCNPs as well as improve their safety, we experimented with a series of phosphonate chemical moieties to passivate particle surfaces through the strong coordination of the organophosphates with RE atoms. Particle screening and physicochemical characterization revealed that ethylenediamine tetra(methylenephosphonic acid) (EDTMP) surface coating provides the most stable UCNPs, which maintain their imaging intensity and do not induce pro-inflammatory effects in vitro and in vivo. In summary, phosphonate coating presents a safer design method that preserves and improves the bioimaging properties of UCNPs, thereby enhancing their biological use.

Phosphonated furan-functionalized poly(ethylene oxide)s using orthogonal click chemistries: synthesis and Diels–Alder reactivity

The synthesis and the reactivity in Diels–Alder and retro Diels–Alder thermoreversible reactions of new phosphonate- and phosphonic acid-terminated furan-functionalized PEO are reported.

Phosphorylation of bio-based compounds: the state of the art

The aim of this review is to present both fundamental and applied research on the phosphorylation of renewable resources, through reactions on naturally occurring functions, and their use in biobased polymer chemistry and applications.