Uncovering the role of yttrium in a cerium-based binary oxide in the catalytic conversion of carbon dioxide and methanol to dimethyl carbonate

Cerium(IV) oxide (CeO2)-based materials are effective catalysts for the synthesis of dimethyl carbonate (DMC) from carbon dioxide (CO2) and methanol (CH3OH). Herein, 5% Y-CeO2 was synthesized by the co-precipitation method. It forms a solid solution structure, which leads to the highest concentration of oxygen vacancies. The Y-VO-Ce active site created by Y3+ doping enhances the adsorption and activation of CO2 based on moderately passivating CH3OH adsorption. Consequently, 5% Y-CeO2 exhibited the highest CH3OH conversion rate of 0.8% and a DMC yield of 15 mmol⋅(g cat)-1, which is 1.4 times of pure CeO2 (reacting in a stainless-steel autoclave at 140 °C with a stirring speed of 1000 r⋅min-1 and an initial pressure of 3.0 MPa for 2 h). An adsorption test and in situ diffuse reflectance infrared Fourier transform spectroscopy showed that 5% Y-CeO2 could effectively inhibit the formation of triple-bonded methoxy species, and promote the formation of bidentate carbonate and bridged methoxy intermediates, which is conducive to the improvement of reaction activity.

CeO2 Frustrated Lewis Pairs Improving CO2 and CH3OH Conversion to Monomethylcarbonate

Frustrated Lewis pairs (FLPs), discovered in the last few decades for homogeneous catalysts and in the last few years also for heterogeneous catalysts, are stimulating the scientific community's interest for their potential in small-molecule activation. Nevertheless, how an FLP activates stable molecules such as CO₂ is still undefined. Through a careful spectroscopic study, we here report the formation of FLPs over a highly defective CeO₂ sample prepared by microwave-assisted synthesis. Carbon dioxide activation over FLP is shown to occur through a bidentate carbonate bridging the FLP and implying a Ce³⁺-to-CO₂ charge transfer, thus enhancing its activation. Carbon dioxide reaction with methanol to form monomethylcarbonate is here employed to demonstrate active roles of FLP and, eventually, to propose a reaction mechanism clarifying the role of Ce³⁺ and oxygen vacancies.

Cu-doped SnS2 nanosheets with superior visible-light photocatalytic CO2 reduction performance

Photocatalytic CO₂ reduction utilizing solar energy is a clean, environment-friendly strategy converting CO₂ into hydrocarbon fuels to solve the energy crisis and climate issues. Herein, we report the synthesis of Cu-doped SnS₂ nanosheets via a simple hydrothermal method. The prepared Cu-doped SnS₂ composite displays superior photocatalytic CO₂ reduction activity. The optimized CH₃OH yield of the composite is two times higher than that of pure SnS₂. The enhanced photocatalytic performance is attributed to effective charge separation resulting from the thinner nanosheets and delocalization of electrons from SnS₂ to Cu, high visible light utilization efficiency, enlarged S_BET, negative shift of the flat-band potential and reduced charge transfer resistance with the introduction of Cu atoms. This work suggests the potential application of Cu-doped SnS₂ in photocatalytic CO₂ reduction.

Ultrasonically assisted surface modified CeO2 nanospindle catalysts for conversion of CO2 and methanol to DMC

This study developed a facile and effective approach to engineer the surface properties of cerium oxide (CeO₂) nanospindle catalysts for the direct synthesis of dimethyl carbonate (DMC) from CO₂ and methanol. CeO₂ nanospindles were first prepared by a simple precipitation method followed by wet chemical redox etching with sodium borohydride (NaBH₄) under high intensity ultrasonication (ultrasonic horn, 20 kHz, 150 W/cm²). The ultrasonically assisted surface modification of the CeO₂ nanospindles in NaBH₄ led to particle collisions and surface reduction that resulted in an increase in the number of surface-active sites of exposed Ce³⁺ and oxygen vacancies. The surface modified CeO₂ nanospindles showed an improvement of catalytic activity for DMC formation, yielding 17.90 mmol·g_cat^-1 with 100 % DMC selectivity. This study offers a simple and effective method to modify a CeO₂ surface, and it can further be applied for other chemical activities.

Sustainable Synthesis of Dimethyl- and Diethyl Carbonate from CO2 in Batch and Continuous Flow-Lessons from Thermodynamics and the Importance of Catalyst Stability

Equilibrium conversions for the direct condensation of MeOH and EtOH with CO₂ to give dimethyl- and diethyl carbonate, respectively, have been calculated over a range of experimentally relevant conditions. The validity of these calculations has been verified in both batch and continuous flow experiments over a heterogeneous CeO₂ catalyst. Operating under optimized conditions of 140 °C and 200 bar CO₂, record productivities of 235 mmol/L·h DMC and 241 mmol/L·h DEC have been achieved using neat alcohol dissolved in a continuous flow of supercritical CO₂. Using our thermodynamic model, we show that to achieve maximum product yield, both dialkyl carbonates and water should be continuously removed from the reactor instead of the conventionally used strategy of removing water alone, which is much less efficient. Catalyst stability rather than activity emerges as the prime limiting factor and should thus become the focus of future catalyst development.

Elucidation of the reaction mechanism on dry reforming of methane in an electric field by in situ DRIFTs

With increasing expectations for carbon neutrality, dry reforming is anticipated for direct conversion of methane and carbon dioxide: the main components of biogas. We have found that dry reforming of methane in an electric field using a Pt/CeO₂ catalyst proceeds with sufficient rapidity even at a low temperature of about 473 K. The effect of the electric field (EF) on dry reforming was investigated using kinetic analysis, in situ DRIFTs, XPS, and DFT calculation. In situ DRIFTs and XPS measurements indicated that the amount of carbonate, which is an adsorbed species of CO₂, increased with the application of EF. XPS measurements also confirmed the reduction of CeO₂ by the reaction of surface oxygen and CH₄. The reaction between CH₄ molecules and surface oxygen was promoted at the interface between Pt and CeO₂.

In the dry reforming of methane in an electric field, the reaction between CH₄ molecules and surface oxygen was promoted at the interface between Pt and CeO₂.

Formation of dimethyl carbonate via direct esterification of CO2 with methanol on reduced or stoichiometric CeO2(111) and (110) surfaces

CeO2-Catalyzed esterification of CO2, a well-known greenhouse gas, with methanol has been widely recognized as a promising alternative method to produce dimethyl carbonate (DMC). Herein, we performed a comprehensive study of catalytic mechanisms underlying the formation of DMC from CO2 and methanol on both stoichiometric and reduced CeO2(111) and (110) surfaces. To this end, the saddle-point searching algorithm is employed. Specifically, using the monomethyl carbonate (MMC) as the key intermediate, a three-step Langmuir-Hinshelwood (LH) mechanism, including the formation and esterification of monomethyl carbonate and removal of water molecule, is identified for the catalytic DMC formation on either the reduced or the stoichiometric CeO2(111) and (110) surfaces. For both CeO2(111) and (110) surfaces, our study indicates that the presence of oxygen vacancies can markedly lower the activation energy barrier. Different rate-limiting steps are identified, however, for the reduced CeO2(111) and (110) surfaces. Successful identification of the rate-limiting step and the associated active CO2 species will provide atomic-level guidance on selection of metal-oxide-based catalysts toward direct synthesis of DMC from the green-house gas CO2 and methanol.

Zr-MOF-808 as Catalyst for Amide Esterification

In this work, zirconium-based metal-organic framework Zr-MOF-808-P has been found to be an efficient and versatile catalyst for amide esterification. Comparing with previously reported homogeneous and heterogeneous catalysts, Zr-MOF-808-P can promote the reaction for a wide range of primary, secondary and tertiary amides with n-butanol as nucleophilic agent. Different alcohols have been employed in amide esterification with quantitative yields. Moreover, the catalyst acts as a heterogeneous catalyst and could be reused for at least five consecutive cycles. The amide esterification mechanism has been studied on the Zr-MOF-808 at molecular level by in situ FTIR spectroscopic technique and kinetic study.

Direct Dimethyl Carbonates Synthesis over CeO2 and Evaluation of Catalyst Morphology Role in Catalytic Performance

In recent years, direct synthesis of dimethyl carbonate (DMC) from carbon dioxide (CO2) has received considerable attention due to green and sustainable technology. Here, we report a production of DMC from major greenhouse gases and CO2 using various morphologies of cerium oxide (CeO2). Time-dependent synthesis of CeO2, with controlled morphology having various shapes including sphere, nanorods and spindle shape, along with its formation mechanism is proposed. The experimental results indicate the morphology of CeO2 was mostly dependent on the reaction time where crystal growth occurred through Ostwald ripening. The morphology, size and shape of CeO2 were observed using transmission electron microscopy (TEM) and field emission scanning electron microscopy (FESEM).The crystallographic analysis using X-ray diffraction (XRD) shows cubic fluorite phase of CeO2 with crystallite size ~72.0 nm using the Debye–Scherrer equation. The nitrogen adsorption desorption technique suggested the formation of the highly mesoporous framework of CeO2 and the excellent surface area around 104.5 m2/g obtained for CeO2 spindles by Brunauer–Emmett–Teller (BET) method. The DMC synthesis reactions were studied over CeO2 catalyst with different morphologies. The results of catalytic reactions specify that the morphology of catalyst plays an important role in their catalytic performances, where spindle shape CeO2 was the most active catalyst producing of up to13.04 mmol of DMC. Furthermore, various dehydrating agents were used to improve the DMC production at optimized reaction parameters. The overall results reveal that the higher surface area and spindle shape of CeO2 makes it a useful, reusable catalyst for one-pot DMC synthesis.

Catalytic CO2 esterification with ethanol for the production of diethyl carbonate using optimized CeO2 as catalyst

The direct conversion of (bio)ethanol and CO₂ is a promising route to diethyl carbonate (DEC) using CeO₂ from optimized catalyst synthesis procedure and cheap reactants originating from renewable resources in bioethanol production.

Solid acid catalyzed carboxymethylation of bio-derived alcohols: an efficient process for the synthesis of alkyl methyl carbonates

Acid catalyzed carboxymethylation of alcohols is an emerging organic transformation that has grabbed the attention of scientific community in recent years. In the present study, sulfonated mesoporous polymer (MP-SO₃H) is presented as a highly active solid acid catalyst to convert a wide range of alcohols into alkyl methyl carbonates. The remarkable catalytic activity of MP-SO₃H is comparable to that of reported homogeneous acid catalysts. A good correlation was established between the catalytic activity and textural properties of the material. An exceptional catalytic activity of MP-SO₃H was observed for DMC mediated carboxymethylation of bio-derived alcohols which is unmatchable to conventional resins and zeolites. This superior activity of MP-SO₃H is ascribed to its intrinsic mesoporosity, high acid strength and uniform coverage of surface area by active sites. The catalyst is recyclable, resistant towards leaching and can be used in successive runs without losing the original activity. To the best of our knowledge, MP-SO₃H is the first solid acid catalyst to exemplify highest activity for the synthesis of different alkyl methyl carbonates using DMC. The protocol developed herein opens up new avenues to transform wide range of bio-alcohols into useful organic carbonates in the future.

Enhancing the Dispersion of Cu-Ni Metals on the Graphene Aerogel Support for Use as a Catalyst in the Direct Synthesis of Dimethyl Carbonate from Carbon Dioxide and Methanol

Graphene has attracted attention because of its interesting properties in catalyst applications including as a catalyst support; however, it is known that the graphene can be restacked, forming a graphite-like structure that leads to poor specific surface area. Hence, the high-porosity graphene aerogel was used as a Cu-Ni catalyst support to produce dimethyl carbonate (DMC) from carbon dioxide and methanol. In this work, we have introduced a new synthesis route, which can improve the dispersion of metal particles on the graphene aerogel support. Cu-Ni/graphene aerogel catalysts were synthesized by a two-step procedure: forming Cu-Ni/graphene aerogel catalysts via hydrothermal reduction and then Cu-Ni loading by incipient wetness impregnation. It is found that the catalyst prepared by the two-step procedure exhibits higher DMC yield (25%) and MeOH conversion (18.5%) than those of Cu-Ni loading only by an incipient wetness impregnation method. The results prove that this new synthesis route can improve the performance of Cu-Ni/graphene aerogel catalysts for DMC production.

Solid base catalysts derived from Ca–Al–X (X = F−, Cl− and Br−) layered double hydroxides for methanolysis of propylene carbonate

The Ca–Al and Ca–Al–X (X = F⁻, Cl⁻ and Br⁻) catalysts were prepared via thermal decomposition of Ca–Al layered double hydroxides (LDHs), and tested for methanolysis of propylene carbonate (PC) to produce dimethyl carbonate (DMC). The catalytic performance of these catalysts increased in the order of Ca–Al–Br⁻ < Ca–Al < Ca–Al–Cl⁻ < Ca–Al–F⁻, which was consistent with the strong basicity of these materials. The recyclability test results showed that the addition of Al and halogens (F⁻, Cl⁻ and Br⁻) not only stabilized the CaO but also improved the recyclability of the catalysts. Particularly, the Ca–Al–F⁻ catalyst exerted the highest stability after 10 recycles. These catalysts have an important value for the exploitation of DMC synthesis by transesterification of PC with methanol.

The CA-F⁻ catalyst modified with Al³⁺ and F⁻ was highly active and recyclable for dimethyl carbonate synthesis.

Synthesis of Carbonates from Alcohols and CO2

Alcohols are ubiquitous compounds in nature that offer modular building blocks for synthetic chemistry. Here we discuss the most recent development of different classes of alcohols and their coupling chemistry with carbon dioxide as to afford linear and cyclic carbonates, the challenges associated with their formation, and the potential of this chemistry to revive a waste carbon feed stock.

Dimethyl carbonate synthesis from carbon dioxide using ceria–zirconia catalysts prepared using a templating method: characterization, parametric optimization and chemical equilibrium modeling

In this paper, a series of Ce_xZr_1−xO₂ solid solution spheres were synthesized by exo- and endo-templating methods and tested for dimethyl carbonate (DMC) synthesis using direct conversion of CO₂.

Infrared spectra of methanol desorption in a He stream and under vacuum on CeO2 and ZrO2 catalyst surfaces

Infrared spectra of methanol desorption in a He stream and under vacuum on CeO₂ and ZrO₂ catalyst surfaces are added for the article (RSC Adv., 2014, 4, 30968) as a response to the letter of Dr F. C. Meunier (RSC Adv., 2016, 6, 17288) and to make the ascription of the bands at 1096, 1054, 1032 and 1012 cm⁻¹ more convincing.

In situ FT-IR spectroscopy investigations of dimethyl carbonate synthesis: on the contribution of gas-phase species

Gas-phase contributions need to be subtracted from in situ IR spectra collected over solids to reveal the spectrum of adsorbates.