Activated carbon based paste electrodes for the simultaneous and effective detection of divalent cadmium and lead ions in wastewater

Heavy metals (HM) have gained significant attention in terms of regular monitoring and detection owing to their toxicity, non-biodegradability, and persistence. Current techniques for detecting HM are expensive, cumbersome, and require sophisticated instruments and skilled labour. Hence, developing cheap, rapid, energy-efficient, and accurate sensors is imperative and electrochemical techniques have emerged as promising tools. The current study involves the fabrication of an electrochemical sensor for the concurrent detection of lead (Pb2+) and cadmium (Cd2+) ions using modified carbon paste electrodes (mCPE). Activated carbon (AC) with a BET surface area of 1118 m2 g-1 was obtained by chemical activation and thermal treatment of the waste rubberwood sawdust. AC-Graphite, AC-Reduced Graphene Oxide (RGO), and AC-RGO-Chitosan were the types of mCPEs that were utilised. The electrochemical behaviours and effects of pH, concentration, and scan rate were studied using Cyclic voltammetry (CV). Studies on detection were conducted using CV and linear sweep voltammetry. Although all the 3 mCPEs detected Cd2+ and Pb2+ in the simulated wastewater, the CPE with RGO and AC could detect Cd2+ as low as 10.91 µg L-1 and Pb2+ as low as 14.01 µg L-1. The work explored the possibility of using AC as a potential sustainable substitute for graphite in CPE.

Nitrogen-doped ordered mesoporous carbon supported ruthenium metallic nanoparticles: Opportunity for efficient hydrogenolysis of biomass-derived 5-hydroxymethylfurfural to 2,5-dimethylfuran by catalytic transfer hydrogenation

One of the most promising solutions to the current energy crisis is an efficient catalytic transformation of abundant low-cost renewable raw biomass into high-quality biofuel. Herein, a highly effective catalyst was constructed systematically for the selective synthesis of 2,5-dimethylfuran (DMF) biofuel from biomass-derived 5-hydroxymethylfurfural (HMF) via green catalytic transfer hydrogenolysis (CTH) using a nitrogen-doped ordered mesoporous carbon (N-CMK-1) decorated ruthenium (Ru)-based catalyst in i-propanol as hydrogen source. The structures and properties of different catalysts were characterized by different characterization techniques such as FTIR, XRD, N2-sorption, CO2-sorption, TGA, TEM, ICP-AES, CHNO analysis, and acid-base back titration. A complete HMF conversion with a high DMF yield of 88% was achieved under optimized reaction conditions. Regarding substrate conversion and product yield, the influence of reaction temperature, time, and hydrogen donors was thoroughly investigated. The nitrogen-promoted carbon support enhanced the dispersion of Ru due to the formation of appropriate basic site density which could efficiently promote the activation of alcohol hydroxyl in i-propanol and subsequent release of active hydrogen species. In the meantime, highly dispersed surface Ru nanoparticles (NPs) were beneficial for hydrogen transfer and activation of both carbonyl and hydroxyl groups in HMF. Moreover, Arrhenius kinetic analysis was studied by identifying 5-methyl furfural (5-MF) and 2,5-bishydroxymethylfuran (BHMF) as two key intermediates that dominate a distinct reaction pathway during hydrogenolysis of HMF to DMF via CTH. Furthermore, high stability without obvious loss of activity after three consecutive cycles was observed in a fabricated N-CMK-1 decorated Ru-based catalyst as a result of superior metal-support interaction and the mesoporous framework nature of the catalyst. These findings would not only offer a robust catalyst synthetic approach but also open a new avenue for the exploitation of biomass to specialty chemicals and advanced biofuels.

A sensitive sandwich-type electrochemical immunosensor using nitrogen-doped graphene/metal-organic framework-derived CuMnCoOx and Au/MXene for the detection of breast cancer biomarker

In terms of cancer-related deaths among women, breast cancer (BC) is the most common. Clinically, human epidermal growth receptor 2 (HER2) is one of the most commonly used diagnostic biomarkers for facilitating BC cell proliferation and malignant growth. In this study, a disposable gold electrode (DGE) modified with gold nanoparticle-decorated Ti3C2Tx (Au/MXene) was utilized as a sensing platform to immobilize the capturing antibody (Ab1/Au/MXene). Subsequently, nitrogen-doped graphene (NG) with a metal-organic framework (MOF)-derived copper-manganese-cobalt oxide, tagged as NG/CuMnCoOx, was used as a probe to label the detection antibody (Ab2). A sandwich-type immunosensor (NG/CuMnCoOx/Ab2/HER2-ECD /Ab1/Au/MXene/DGE) was developed to quantify HER2-ECD. NG/CuMnCoOx enhances the conductivity, electrocatalytic active sites, and surface area to immobilize Ab2. In addition, Au/MXene facilitates electron transport and captures more Ab1 on its surface. Under optimal conditions, the resultant immunosensor displayed an excellent linear range of 0.0001 to 50.0 ng. mL-1. The detection limit was 0.757 pg·mL-1 with excellent selectivity, appreciable reproducibility, and high stability. Moreover, the applicability for determining HER2-ECD in human serum samples indicates its ability to monitor tumor markers clinically.

Electrocatalytic Oxygen Reduction Reaction of Graphene Oxide and Metal-Free Graphene in an Alkaline Medium

Graphene is a well-known two-dimensional material with a large surface area and is used for numerous applications in a variety of fields. Metal-free carbon materials such as graphene-based materials are widely used as an electrocatalyst for oxygen reduction reactions (ORRs). Recently, more attention has been paid to developing metal-free graphenes doped with heteroatoms such as N, S, and P as efficient electrocatalysts for ORR. In contrast, we found our prepared graphene from graphene oxide (GO) by the pyrolysis method under a nitrogen atmosphere at 900 °C has shown better ORR activity in aqueous 0.1 M potassium hydroxide solution electrolyte as compared with the electrocatalytic activity of pristine GO. At first, we prepared various graphene by pyrolysis of 50 mg and 100 mg of GO in one to three alumina boats and pyrolyzed the samples under a N₂ atmosphere at 900 °C. The prepared samples are named G50-1B to 3B and G100-1B and G100-2B. The prepared GO and graphenes were also analyzed under various characterization techniques to confirm their morphology and structural integrity. The obtained results suggest that the ORR electrocatalytic activity of graphene may differ based on the pyrolysis conditions. We found that G100-1B (E_onset, E_1/2, J_L, and n values of 0.843, 0.774, 4.558, and 3.76) and G100-2B (E_onset, E_1/2, and J_L values of 0.837, 0.737, 4.544, and 3.41) displayed better electrocatalytic ORR activity, as did Pt/C electrode (E_onset, E_1/2, and J_L values of 0.965, 0.864, 5.222, and 3.71, respectively). These results display the wide use of the prepared graphene for ORR and also can be used for fuel cell and metal-air battery applications.

Antimicrobial, anticancer, and biofilm inhibition studies of highly reduced graphene oxide (HRG): In vitro and in silico analysis

Background: Bacterial infections and cancers may cause various acute or chronic diseases, which have become serious global health issues. This requires suitable alternatives involving novel and efficient materials to replace ineffective existing therapies. In this regard, graphene composites are being continuously explored for a variety of purposes, including biomedical applications, due to their remarkable properties.

Methods: Herein, we explore, in-vitro, the different biological properties of highly reduced graphene oxide (HRG), including anti-cancer, anti-bacterial, and anti-biofilm properties. Furthermore, to analyze the interactions of graphene with proteins of microbes, in silico docking analysis was also carried out. To do this, HRG was prepared using graphene oxide as a precursor, which was further chemically reduced to obtain the final product. The as-prepared HRG was characterized using different types of microscopic and spectroscopic techniques.

Results: The HRG revealed significant cytotoxic ability, using a dose-dependent anti-cell proliferation approach, which substantially killed human breast cancer cells (MCF-7) with IC50 of 29.51 ± 2.68 μg/mL. The HRG demonstrated efficient biological properties, i.e., even at low concentrations, HRG exhibited efficient anti-microbial properties against a variety of microorganisms. Among the different strains, Gram-positive bacteria, such as B. subtilis, MRSA, and S. aureus are more sensitive to HRG compared to Gram-negative bacteria. The bactericidal properties of HRG are almost similar to a commercially available effective antibiotic (ampicillin). To evaluate the efficacy of HRG against bacterial biofilms, Pseudomonas aeruginosa and MRSA were applied, and the results were compared with gentamycin and ampicillin, which are commonly applied standard antibiotics. Notably, HRG demonstrated high inhibition (94.23%) against P.aeruginosa, with lower MIC (50 μg/mL) and IC50 (26.53 μg/mL) values, whereas ampicillin and gentamicin showed similar inhibition (90.45% and 91.31% respectively) but much higher MIC and IC50 values.

Conclusion: Therefore, these results reveal the excellent biopotential of HRG in different biomedical applications, including cancer therapy; antimicrobial activity, especially anti-biofilm activity; and other biomedicine-based therapies. Based on the molecular docking results of Binding energy, it is predicted that pelB protein and HRG would form the best stable docking complex, and high hydrogen and hydrophobic interactions between the pelB protein and HRG have been revealed. Therefore, we conclude that HRG could be used as an antibiofilm agent against P. aeruginosa infections.

Assessment of Physicochemical, Anticancer, Antimicrobial, and Biofilm Activities of N-Doped Graphene

Nanomedicine has been used as a precise treatment for many diseases. The advantage of using nanodrugs is that they have more permeability and less toxicity to cells, which enhances the drug delivery system. Graphene is well known for its potential biological applications in drug, food, and pharma industries. This study aimed to assess the productivity and potentiality of nitrogen-doped graphene (NDG) and to evaluate their anticancer, antimicrobial, and biofilm inhibition activity. Nitrogen-doped graphene was synthesized by using a one-pot facile synthesis of NDG, wherein the NDG was prepared by the reduction of graphene oxide (GO) in the presence of hydrazine hydrate as a reducing agent, while ammonium hydroxide was used as a source of nitrogen on the surface of graphene. As-synthesized NDG was characterized by various characterization techniques such as UV-Vis, FT-IR, XRD, XPS, TEM, and N2 sorption studies analysis. Antimicrobial, anticancer, and biofilm inhibition assays were performed by standard protocols. N-doped graphene (NDG) showed better activity against Gram-positive bacteria, such as methicillin-resistant Staphylococcus aureus (MRSA), Bacillus subtillis, Streptococcus pneumoniae, and Streptococcus mutans (p ≤ 0.05), whereas there was no activity against Gram-negative strains in Klebsiella pneumoniae and Pseudomonas aeruginosa. Biofilm inhibition was also improved with NDG compared to the standard ampicillin. NDG showed better results in both MCF-7 and Hela cell lines with IC50 of 27.15 µg/mL and 30.85 µg/mL, respectively. In conclusion, NDG has the best ability for use as a biomolecule, and research studies focusing on proteomics, metabolomics, and in vivo studies are needed to increase the impact of NDG in the drug and pharma industry.

Graphene Oxide and Nitrogen-Doped Graphene Coated Copper Nanoparticles in Water-Based Nanofluids for Thermal Management in Electronics

Graphene oxide (GO) and nitrogen-doped graphene (NG) coated copper nanoparticles (NPs) have been developed in this work and investigated as nanofiller for water as Heat Transfer Fluids (HTFs). The morphology and composition of the coating were characterized to confirm the presence of functional groups and the nitrogendoping of the graphene coating. Different fractions of the two types of coated nanoparticles NPs between 0.1 and 10 wt.% were dispersed in water. The thermal conductivity of the dispersions was evaluated at temperatures between 20 and 50 °C. A positive correlation between the thermal conductivity of the HTFs and the fraction and temperature are observed as a result of the increase of the solid phase contribution into the heat transfer. At a concentration of 0.5 wt.%, the thermal conductivity of the NG-CuNPs nanofluid reached its maximum increase of 78%, compared to a 13% increase in the case of GO-CuNPs. However, due to the poor stability of the NG-CuNPs, further increase of the solid phase did not result in any additional improvement. In contrast, the thermal conductivity of the GO-based dispersion resulted in a 103% enhancement at 10 wt.% at a temperature of 50 °C.

Evaluation of N doped rGO-ZnO-CoPc(COOH)8 nanocomposite in cyanide degradation and its bactericidal activities

In the present study, an attempt has been made to design a solar light driven N-rGO-ZnO- CoPc(COOH)₈ nanocomposite for the degradation of cyanide. The morphological and structural characterization of the synthesized nanocomposite was performed by XRD, FT-IR, XPS, UV-vis DRS, FESEM, TEM, EDS, PL spectra and BET surface area. The results revealed that almost 91% degradation and 86% toxicity removal occurred at 25 mgL^-1 of initial cyanide concentration by the N-rGO-ZnO-CoPc(COOH)₈ nanocomposite under illumination of solar light within 120 min. Analysis of free radicals reveals that the generation of OH^. radicals was the predominant species in the photocatalytic degradation process. The cyanide degradation follows pseudo-first order kinetics. The estimated apparent rate constant (K_app) of the above nanocomposite was 3 times higher than that of the ZnO photocatalyst alone together with a very good recycle activities. This might be due to the application of metallpthalocyanine photosensitizer CoPc(COOH)₈ which enhances the rate of visible light absorption efficiency and activates the higher band gap ZnO photocatalyst under visible light. In addition, the presence of residual oxygen in N-rGO also promotes nucleation and anchor sites for interfacial contact between ZnO and N-rGO for effective charge transfer. Further, the N-rGO-ZnO-CoPc(COOH)₈ photocatalytic system showed significant antibacterial activities against mixed culture systems. Therefore, the N-rGO-ZnO-CoPc(COOH)₈ nanocomposite may be an alternative solar light driven photocatalyst system for the removal of cyanide from the wastewater along with its strong disinfectant activities.

Exploring supercapacitance of solvothermally synthesized N-rGO sheet: role of N-doping and the insight mechanism

We demonstrate the method of achieving excellent supercapacitance in nitrogen-doped reduced graphene oxide (N-rGO) sheets by controlling the amount of N-content through the use of different ratios of GO and urea during solvothermal synthesis. Here, urea plays a dual role in reducing GO and simultaneously doping nitrogen into the GO flakes forming exfoliated N-rGO sheets. The nitrogen content in N-rGO samples rises with an increase in the amounts of urea and saturates at a value of ∼14% for the GO : urea ratios beyond 1 : 8. The obtained N-rGO sheets with ∼ 5% N-content (obtained for GO : urea ratio of 1 : 3) were demonstrated as excellent supercapacitor materials. Using a 3-electrode setup, the maximum specific capacitance obtained for this sample was 514 F g^-1 at a current density of 0.5 A g^-1 (mass normalized current). The insights into the origin of this excellent supercapacitive behavior are explained through our results on optimum N-content, the relative amount of different N-environments, defects/disorders, and the degree of reduction of GO. Importantly, a proper stacking of rGO sheets with moderate N-content (∼5-6%) and a moderate amount of defects is the key to achieve high specific-capacitance. Furthermore, our 2-electrode device demonstrates the excellence of our samples with a C_sp of 237 F g^-1, a power density of 225 W kg^-1, and an energy density of 6.7 W h kg^-1 at 0.5 A g^-1, exhibiting a high cyclic constancy with high capacitive retention of ∼ 82% even after 8000 cycles. Hence, our work provides a way to control the properties of N-rGO in achieving excellent supercapacitive performance.

Effect of Nitrogen Doping on the Optical Bandgap and Electrical Conductivity of Nitrogen-Doped Reduced Graphene Oxide

Graphene as a material for optoelectronic design applications has been significantly restricted owing to zero bandgap and non-compatible handling procedures compared with regular microelectronic ones. In this work, nitrogen-doped reduced graphene oxide (N-rGO) with tunable optical bandgap and enhanced electrical conductivity was synthesized via a microwave-assisted hydrothermal method. The properties of the synthesized N-rGO were determined using XPS, FTIR and Raman spectroscopy, UV/vis, as well as FESEM techniques. The UV/vis spectroscopic analysis confirmed the narrowness of the optical bandgap from 3.4 to 3.1, 2.5, and 2.2 eV in N-rGO samples, where N-rGO samples were synthesized with a nitrogen doping concentration of 2.80, 4.53, and 5.51 at.%. Besides, an enhanced n-type electrical conductivity in N-rGO was observed in Hall effect measurement. The observed tunable optoelectrical characteristics of N-rGO make it a suitable material for developing future optoelectronic devices at the nanoscale.

Competitive role of nitrogen functionalities of N doped GO and sensitizing effect of Bi2O3 QDs on TiO2 for water remediation

The promising solar irradiated photocatalyst by pairing of bismuth oxide quantum dots (BQDs) doped TiO₂ with nitrogen doped graphene oxide (NGO) nanocomposite (NGO/BQDs-TiO₂) was fabricated. It was used for degradation of organic pollutants like 2,4-dichlorophenol (2,4-DCP) and stable dyes, i.e. Rhodamine B and Congo Red. X-ray diffraction (XRD) profile of NGO showed reduction in oxygenic functional groups and restoring of graphitic crystal structure. The characteristic diffraction peaks of TiO₂ and its composites showed crystalline anatase TiO₂. Morphological images represent spherical shaped TiO₂ evenly covered with BQDs spread on NGO sheet. The surface linkages of NO-O-Ti, C-O-Ti, Bi-O-Ti and vibrational modes are observed by Fourier transform infrared spectroscopy (FTIR) and Raman studies. BQDs and NGO modified TiO₂ results into red shifting in visible region as studied in diffused reflectance spectroscopy (DRS). NGO and BQDs in TiO₂ are linked with defect centers which reduced the recombination of free charge carriers by quenching of photoluminescence (PL) intensities. X-ray photoelectron spectroscopy (XPS) shows that no peak related to C-O in NGO/BQDs-TiO₂ is observed. This indicated that doping of nitrogen into GO has reduced some oxygen functional groups. Nitrogen functionalities in NGO and photosensitizing effect of BQDs in ternary composite have improved photocatalytic activity against organic pollutants. Intermediate byproducts during photo degradation process of 2,4-DCP were studied through high performance liquid chromatography (HPLC). Study of radical scavengers indicated that O₂^·- has significant role for degradation of 2,4-DCP. Our investigations propose that fabricated nanohybrid architecture has potential for degradation of environmental pollutions.

Coconut-Water-Mediated Carbonaceous Electrode: A Promising Eco-Friendly Material for Bifunctional Water Splitting Application

The organic and eco-friendly materials are extended to prevail over the worldwide energy crisis where bio-inspired carbonaceous electrode materials are being prepared from biogenic items and wastes. Here, coconut water is sprayed over three-dimensional (3D) nickel foam for obtaining a carbonaceous electrode material, i.e., C@Ni-F. The as-prepared C@Ni-F electrode has been used for structural elucidation and morphology evolution studies. Field emission scanning electron microscopy analysis confirms the vertically grown nanosheets of the C@Ni-F electrode, which is further employed in the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), where excellent OER and HER performances with small overpotentials of 219 and 122 mV and with stumpy Tafel slopes, i.e., 27 and 53 mV dec-1, are respectively obtained, suggesting a bifunctional potential of the sprayed electrode material. Moreover, sustainable bifunctional performance of C@Ni-F proves considerable chemical stability and moderate mechanical robustness against long-term operation, suggesting that, in addition to being a healthy drink to mankind, coconut water can also be used for water splitting applications.

Enhanced electrostatic potential with high energy and power density of a symmetric and asymmetric solid-state supercapacitor of boron and nitrogen co-doped reduced graphene nanosheets for energy storage devices

Schematic representation of boron and nitrogen co-doped graphene nanosheets.

Mixed Dye Removal Efficiency of Electrospun Polyacrylonitrile-Graphene Oxide Composite Membranes

Exfoliated graphene oxide (GO) was reliably modified with a cetyltrimethylammonium chloride (CTAC) surfactant to greatly improve the dispersity of the GO in a polyacrylonitrile (PAN) polymer precursor solution. Subsequent electrospinning of the mixture readily resulted in the formation of GO-PAN composite nanofibers containing up to 30 wt % of GO as a filler without notable defects. The absence of common electrospinning problems associated with clogging and phase separation indicated the systematic and uniform integration of the GO within the PAN nanofibers beyond the typical limits. After thoroughly examining the formation and maximum loading efficiency of the modified GO in the PAN nanofibers, the resulting composite nanofibers were thermally treated to form membrane-type sheets. The wettability and pore properties of the composite membranes were notably improved with respect to the pristine PAN nanofiber membrane, possibly due to the reinforcing filler effect. In addition, the more GO loaded into the PAN nanofiber membranes, the higher the removal ability of the methylene blue (MB) and methyl red (MR) dyes in the aqueous system. The adsorption kinetics of a mixed dye solution were also monitored to understand how these MB and MR dyes interact differently with the composite nanofiber membranes. The simple surface modification of the fillers greatly facilitated the integration efficiency and improved the ability to control the overall physical properties of the nanofiber-based membranes, which highly impacted the removal performance of various dyes from water.

Engineering Heterostructured Thin-Film Nanocomposite Membrane with Functionalized Graphene Oxide Quantum Dots (GOQD) for Highly Efficient Reverse Osmosis

In this study, custom-tailored graphene oxide quantum dots (GOQD) were synthesized as functional nanofillers to be embedded into the polyamide (PA) membrane for reverse osmosis (RO) via interfacial polymerization (IP). The heterostructured interface-functionalization of amine/sulfonic decoration on GOQD (N/S-d-GOQD) takes place via the tuning of the molecular design. The embedded N/S-d-GOQD inside the PA matrix contributes to facilitating water molecules quick transport due to the more accessible capturing sites with higher internal polarity, achieving a nearly 3-fold increase in water permeance when compared to the pristine thin-film composite (TFC) membrane. Covalent bonding between the terminal amine groups and the acyl chloride of trimesoyl chloride (TMC) enables the formation of an amplified selective layer, while the sulfonic part assists in maintaining a robust membrane surface negative charge, thus remarkably improving the membrane selectivity toward NaCl. As a result, the newly developed TFN membrane performed remarkably high water permeance up to 5.89 L m^-2 h^-1 bar^-1 without the compromising of its favorable salt (NaCl) rejection ratio of 97.1%, revealing a comparably high separation property when comparing to the state-of-the-art RO membranes, and surpassing the permeability-selectivity trade-off limits. Furthermore, we systematically investigated the GOQDs with different surface decorations but similar configurations (including 3 different nanofillers of pristine GOQD, amine decorated GOQD (N-d-GOQD), and N/S-d-GOQD) to unveil the underlying mechanisms of the swing effects of internal geometry and polarity of the embedded nanofillers on contributing to the uptake, and/or release of aqueous molecules within TFN membranes, providing a fundamental perspective to investigate the impact of embedded nanofillers on the formation of an IP layer and the overall transporting behavior of the RO process.

Synthesis and Electrochemical Study of Three-Dimensional Graphene-Based Nanomaterials for Energy Applications

Graphene is an attractive soft material for various applications due to its unique and exclusive properties. The processing and preservation of 2D graphene at large scales is challenging due to its inherent propensity for layer restacking. Three-dimensional graphene-based nanomaterials (3D-GNMs) preserve their structures while improving processability along with providing enhanced characteristics, which exhibit some notable advantages over 2D graphene. This feature article presents recent trends in the fabrication and characterization of 3D-GNMs toward the study of their morphologies, structures, functional groups, and chemical compositions using scanning electron microscopy, X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. Owing to the attractive properties of 3D-GNMs, which include high surface areas, porous structures, improved electrical conductivity, high mechanical strength, and robust structures, they have generated tremendous interest for various applications such as energy storage, sensors, and energy conversion. This article summarizes the most recent advances in electrochemical applications of 3D-GNMs, pertaining to energy storage, where they can serve as supercapacitor electrode materials and energy conversion as oxygen reduction reaction catalysts, along with an outlook.

Tuning the type of nitrogen on N-RGO supported on N-TiO2 under ultrasonication/hydrothermal treatment for efficient hydrogen evolution - A mechanistic overview

Efficient hydrogen production through water splitting has been the challenging task to be achieved in the present context of energy crisis. Among the various catalysts employed, nitrogen doped Titanium dioxide/Reduced graphene oxide (N-TiO₂/RGO) nanocomposite has been established to be a promising photocatalytic material for this purpose. However, nuances of doping nitrogen on TiO₂ and the type of nitrogen (pyridinic, pyrrolic and graphitic) stabilized on RGO responsible for facilitating the H₂ production has not yet been addressed mechanistically. In the present investigation, an attempt has been made to synthesise N-Titanium dioxide/N-Reduced graphene oxide (NTNG) nanocomposite under ultrasonication followed by hydrothermal treatment. A stainlesssteel ultrasonic bath, of 6.5 L tank size (LxBxH) 300 × 150 × 150 mm, was used for ultrasonic treatments. The transducers located at the bottom of the ultrasonic bath generate a frequency of 40 kHz with maximum power of 200 W. A mechanism has been proposed including the nuances of formation and the stabilisation of each type of nitrogen on N-RGO as a function of ultrasonication time. The present work supports the stabilization of a given type of nitrogen on RGO through keto enol tautomerism. XPS and FTIR studies have been undertaken to identify the different types of nitrogen doping and the presence of functional groups respectively. XRD, UV-Vis DRS and PL investigations have been made to establish morphological profile and band gap structure of the nanocomposite. It was observed that pyrrolic type nitrogen stabilized on N-RGO augments the efficiency of photocatalytic activity through hydrogen production by water splitting.

A 3D nitrogen-doped graphene aerogel for enhanced visible-light photocatalytic pollutant degradation and hydrogen evolution

The synergistic effect of the 3D structure and N-doping explain the high surface area of 536 m² g⁻¹ and excellent photocatalytic activity.

Insight into the photophysics of strong dual emission (blue & green) producing graphene quantum dot clusters and their application towards selective and sensitive detection of trace level Fe3+ and Cr6+ ions

Graphene-nanostructured systems, such as graphene quantum dots (GQDs), are well known for their interesting light-emitting characteristics and are being applied to a variety of luminescence-based applications. The emission properties of GQDs are complex. Therefore, understanding the science of the photophysics of coupled quantum systems (like quantum clusters) is still challenging. In this regard, we have successfully prepared two different types of GQD clusters, and explored their photophysical properties in detail. By co-relating the structure and photophysics, it was possible to understand the emission behavior of the cluster in detail. This gave new insight into understanding the clustering effect on the emission behaviour. The results clearly indicated that although GQDs are well connected, the local discontinuity in the structure prohibits the dynamics of photoexcited charge carriers going from one domain to another. Therefore, an excitation-sensitive dual emission was possible. Emission yield values of about 18% each were recorded at the blue and green emission wavelengths at a particular excitation energy. This meant that the choice of emission color was decided by the excitation energy. Through systematic analysis, it was found that both intrinsic and extrinsic effects contributed to the blue emission, whereas only the intrinsic effect contributed to the green emission. These excitation-sensitive dual emissive GQD clusters were then used to sense Fe³⁺ and Cr⁶⁺ ions in the nanomolar range. While the Cr⁶⁺ ions were able to quench both blue and green emissions, the Fe³⁺ ions quenched blue emission only. The insensitivity of the Fe³⁺ ions in the quenching of the green emission was also understood through quantum chemical calculations.

Schematic representation for the origin of blue and green emissions, and the resultant PL emission spectra from the GQD interconnected cluster-type sample.

Facile one-pot synthesis of water-dispersible phosphate functionalized reduced graphene oxide toward high-performance energy storage devices

Phosphate functionalized carbon nanomaterials have attracted significant attention because of their potential applications in energy storage applications. Herein we report a facile one-pot method to prepare water dispersible phosphate functionalized reduced graphene oxide and demonstrate the potential of the novel materials for energy storage applications. The synthesis method shows promise to promote a wider adoption of reduced graphene oxide for high performance applications.

Heteroatom-doped graphene as sensing materials: a mini review

Graphene is one of the astounding recent advancements in current science and one of the most encouraging materials for application in cutting-edge electronic gadgets. Graphene and its derivatives like graphene oxide and reduced graphene oxide have emerged as significant nanomaterials in the area of sensors. Furthermore, doping of graphene and its derivatives with heteroatoms (B, N, P, S, I, Br, Cl and F) alters their electronic and chemical properties which are best suited for the construction of economical sensors of practical utility. This review recapitulates the developments in graphene materials as emerging electrochemical, ultrasensitive explosive, gas, glucose and biological sensors for various molecules with greater sensitivity, selectivity and a low limit of detection. Apart from the most important turn of events, the properties and incipient utilization of the ever evolving family of heteroatom-doped graphene are also discussed. This review article encompasses a wide range of heteroatom-doped graphene materials as sensors for the detection of NH₃, NO₂, H₂O₂, heavy metal ions, dopamine, bleomycinsulphate, acetaminophen, caffeic acid, chloramphenicol and trinitrotoluene. In addition, heteroatom-doped graphene materials were also explored for sensitivity and selectivity with respect to interfering analytes present in the system. Finally, the review article concludes with future perspectives for the advancement of heteroatom-doped graphene materials.

Graphene is one of the astounding recent advancements in current science and one of the most encouraging materials for application in cutting-edge electronic gadgets.

Extensive removal of thallium by graphene oxide functionalized with aza-crown ether

Thallium (Tl) is a highly toxic heavy metal, and its pollution and remediation in aquatic environments has attracted considerable attention. To reduce or remove Tl pollution in the environment, various strategies have been applied. Graphene oxide (GO) has abundant oxygen-containing functional groups, indicating its high application potential for pollution remediation via methods involving binding to metal ions or positively charged organic molecules or electrostatic interaction and coordination. However, the adsorption of Tl to GO occurs via physical adsorption, for which the adsorption efficiency is low. Therefore, herein, we report a new method to effectively remove Tl pollution in water. We combined GO with aza-crown ether, which enhanced the electronegativity and ability to bind metal ions. The functionalized graphene oxide (FGO) demonstrated high efficiency through a wide pH gradient of 5–10, with a dominant Tl(i) adsorption capacity (112.21 mg g⁻¹) based on the Langmuir model (pH 9.0, adsorbent concentration of 0.8 g L⁻¹). The adsorption of Tl(i) during removal fit a pseudo-second-order kinetic model well. The mechanisms of Tl removal involve physical and chemical adsorption. In summary, our study provides a new method for the detection and treatment of Tl-containing wastewater by using FGO.

Thallium (Tl) is a highly toxic heavy metal, and its pollution and remediation in aquatic environments has attracted considerable attention.

Effect of Doping Temperatures and Nitrogen Precursors on the Physicochemical, Optical, and Electrical Conductivity Properties of Nitrogen-Doped Reduced Graphene Oxide

The greatest challenge in graphene-based material synthesis is achieving large surface area of high conductivity. Thus, tuning physico-electrochemical properties of these materials is of paramount importance. An even greater problem is to obtain a desired dopant configuration which allows control over device sensitivity and enhanced reproducibility. In this work, substitutional doping of graphene oxide (GO) with nitrogen atoms to induce lattice–structural modification of GO resulted in nitrogen-doped reduced graphene oxide (N-rGO). The effect of doping temperatures and various nitrogen precursors on the physicochemical, optical, and conductivity properties of N-rGO is hereby reported. This was achieved by thermal treating GO with different nitrogen precursors at various doping temperatures. The lowest doping temperature (600 °C) resulted in less thermally stable N-rGO, yet with higher porosity, while the highest doping temperature (800 °C) produced the opposite results. The choice of nitrogen precursors had a significant impact on the atomic percentage of nitrogen in N-rGO. Nitrogen-rich precursor, 4-nitro-ο-phenylenediamine, provided N-rGO with favorable physicochemical properties (larger surface area of 154.02 m² g⁻¹) with an enhanced electrical conductivity (0.133 S cm⁻¹) property, making it more useful in energy storage devices. Thus, by adjusting the doping temperatures and nitrogen precursors, one can tailor various properties of N-rGO.

One-step selective laser patterning of copper/graphene flexible electrodes

Flexible electrodes have attracted much attention in consumer electronic applications. In this work, laser direct writing is used to fabricate copper/graphene composite electrodes on a flexible substrate in one step. This direct writing process with a low power laser can reduce copper ions in thin films to form copper nanomaterials and spontaneously interconnect them to gain good conductivity, while the laser also induces the growth of multi-layer graphene that coats on copper to improve the oxidation resistance of electrodes. The electrical performance and chemical composition of flexible electrodes can be tuned by laser power, scanning speed, and defocus distance. A mechanism of in situ reduction and interconnection of copper nanomaterials during laser direct writing has been proposed. This method could largely reduce the oxidation issue by avoiding synthesis and sintering processes of copper nanomaterials. These as-written copper electrodes have good stability and have potential applications in flexible electronics, such as flexible heaters or antennas as demonstrated.

Facile synthesis of N-doped graphene supported porous cobalt molybdenum oxynitride nanodendrites for the oxygen reduction reaction

Exploring an inexpensive, active and stable electrocatalyst as an alternative to expensive Pt for the oxygen reduction reaction (ORR), porous Co-Mo-ON alloy nanodendrites supported on nitrogen-doped graphene (Co-Mo-ON/NG) have been synthesized by a two-step solid state heating method. The Co-Mo-ON/NG nanodendrites offer high ORR activity and superior electrochemical stability both in acidic and alkaline media. This superiority is due to the synergistic effect of NG, enhanced catalytic efficiency by Mo, highly active intrinsic surface area and exposure of catalytic facets of nanodendritic morphology towards the ORR. The Co-Mo-ON/NG nanodendrites show a 4e- ORR process with 0.710 V and 0.915 V onset potentials in 0.5 M H2SO4 and 0.1 M KOH, respectively. The Co-Mo-ON/NG nanodendrites show extreme electrochemical stability in terms of 96% and 97% current retention for 40 000 s in both acidic and alkaline media, respectively, long term durability for continuous 2000 cycles and greater resistance to methanol than the commercial Pt/C catalyst. Furthermore, Mo-ON/NG, Co-ON/NG, and Co-Mo-ON are also tested to evaluate the effect of Mo-doping and NG on the electrocatalytic activity of Co-Mo-ON/NG nanodendrites. Owing to their low cost, easy synthesis, outstanding ORR performance, and extreme durability, Co-Mo-ON/NG nanodendrites emerged as a promising non-precious and highly stable ORR electrocatalyst in fuel cell applications.

Magnetron Sputter-Coated Nanoparticle MoS2 Supported on Nanocarbon: A Highly Efficient Electrocatalyst toward the Hydrogen Evolution Reaction

The design and fabrication of inexpensive highly efficient electrocatalysts for the production of hydrogen via the hydrogen evolution reaction (HER) underpin a plethora of emerging clean energy technologies. Herein, we report the fabrication of highly efficient electrocatalysts for the HER based on magnetron-sputtered MoS₂ onto a nanocarbon support, termed MoS₂/C. Magnetron sputtering time is explored as a function of its physiochemical composition and HER performance; increased sputtering times give rise to materials with differing compositions, i.e., Mo⁴⁺ to Mo⁶⁺ and associated S anions (sulfide, elemental, and sulfate), and improved HER outputs. An optimized sputtering time of 45 min was used to fabricate the MoS₂/C material. This gave rise to an optimal HER performance with regard to its HER onset potential, achievable current, and Tafel value, which were -0.44 (vs saturated calomel electrode (SCE)), -1.45 mV s^-1, and 43 mV dec^-1, respectively, which has the highest composition of Mo⁴⁺ and sulfide (MoS₂). Electrochemical testing toward the HER via drop casting MoS₂/C upon screen-printed electrodes (SPEs) to electrically wire the nanomaterial is found to be mass coverage dependent, where the current density increases up to a critical mass (ca. 50 μg cm^-2), after which a plateau is observed. To allow for a translation of the bespoke fabricated MoS₂/C from laboratory to new industrial applications, MoS₂/C was incorporated into the bulk ink utilized in the fabrication of SPEs (denoted as MoS₂/C-SPE), thus allowing for improved electrical wiring to the MoS₂/C and resulting in the production of scalable and reproducible electrocatalytic platforms. The MoS₂/C-SPEs displayed far greater HER catalysis with a 450 mV reduction in the HER onset potential and a 1.70 mA cm^-2 increase in the achievable current density (recorded at -0.75 V (vs SCE)), compared to a bare/unmodified graphitic SPE. The approach of using magnetron sputtering to modify carbon with MoS₂ facilitates the production of mass-producible, stable, and effective electrode materials for possible use in electrolyzers, which are cost competitive to Pt and mitigate the need to use time-consuming and low-yield exfoliation techniques typically used to fabricate pristine MoS₂.

High Electrochemical Performance Phosphorus-Oxide Modified Graphene Electrode for Redox Supercapacitors Prepared by One-Step Electrochemical Exfoliation

Phosphorus oxide modified graphene was prepared by one-step electrochemical anodic exfoliation method and utilized as electrode in a redox supercapacitor that contained potassium iodide in electrolytes. The whole preparation process was completed in a few minutes and the yield was about 37.2%. The prepared sample has better electrocatalysis activity for I⁻/I⁻₃ redox reaction than graphite due to the good charge transfer performance between phosphorus oxide and iodide ions. The maximum discharge specific capacitance is 1634.2 F/g when the current density is 3.5 mA/cm² and it can keep at 463 F/g after 500 charging–discharging cycles when the current density increased about three times.

Nitrogen Graphene: A New and Exciting Generation of Visible Light Driven Photocatalyst and Energy Storage Application

The synthesis of nitrogen, boron, and nitrogen-boron-codoped graphenes was attained via mixing solutions of GO with urea, boric acid, and a mixture of both, respectively, followed by drying in vacuum and annealing at 900 °C for 10 h. These materials were thoroughly characterized employing XRD, TEM, FTIR, Raman, UV-vis, XPS, IPCE%, and electrical conductivity measurements. The nitrogen-doped graphene (NG) showed an excellent supercapacitor performance with a higher specific capacitance (388 F·g-1 at 1 A·g-1), superior stability, and a higher power density of 0.260 kW kg-1. This was mainly due to the designated N types of doping and most importantly N-O bonds and to lowering charge transfer and equivalent series resistances. The NG also indicated the highest photocatalytic performance for methylene blue (MB 20 ppm, power = 160 W, λ > 420 nm) and phenol (5 ppm) degradation under visible light illumination with rate constants equal 0.013 min-1 and 0.04 min-1, respectively. The photodegradation mechanism was proposed via determining the energy band potentials using the Mott-Schottky measurements. This determined that photoactivity enhancement of the NG is accounted for by acquisition of nitrogen-oxy-carbide phases that shared in inducing a higher IPCE% (60%) and a lower band gap value (1.68 eV) compared to boron and nitrogen-boron-codoped graphenes. The achieved photodegradation mechanism relied on scavengers performance suggesting that •OH and electrons were the main reactive species responsible for the MB photodegradation.

CuAg@Ag Core-Shell Nanostructure Encapsulated by N-Doped Graphene as a High-Performance Catalyst for Oxygen Reduction Reaction

Development of a robust, cost-effective, and efficient catalyst is extremely necessary for oxygen reduction reaction (ORR) in fuel cell applications. Herein, we reported a well-defined nanostructured catalyst of highly dispersed CuAg@Ag core-shell nanoparticle (NP)-encapsulated nitrogen-doped graphene nanosheets (CuAg@Ag/N-GNS) exhibiting a superior catalytic activity toward ORR in alkaline medium. The synergistic effects produced from the unique properties of CuAg@Ag core-shell NPs and N-GNS made such a novel nanohybrid display a catalytic behavior comparable to that of the commercial Pt/C product. In particular, it demonstrated a much better stability and methanol tolerance than Pt/C under the same conditions. Because of its outstanding electrochemical performance and ease of synthesis, CuAg@Ag/N-GNS material was expected to be a promising low-cost catalyst for ORR in alkaline fuel cell applications.

Effect of Dimensionality and Doping in Quasi-"One-Dimensional (1-D)" Nitrogen-Doped Graphene Nanoribbons on the Oxygen Reduction Reaction

Designing an efficient metal-free electrocatalyst for the oxygen reduction reaction (ORR) is a challenging research theme having enormous practical importance in several renewable energy technologies like fuel cell and metal-air batteries. Here we discuss a cost-effective and commercially viable strategy to develop high-performance nitrogen-doped graphene nanoribbon (N-GNR), which is a quasi-"one-dimensional" analogue of graphene. We have selected the N-GNR system to identify the doping-induced variation in the distribution of active catalytic sites experimentally in graphene-based electrocatalysts. N-GNR exhibits a comparable exchange current density (1.65 × 10^-9 vs 2.25 × 10^-9 A cm^-2), thermodynamic potential (0.80 vs 0.83 V), and smaller Tafel slope (55 vs 60 mV dec^-1) with respect to the benchmarking platinum/carbon (Pt/C), and also, more precisely, it goes through a four-electron pathway with low hydrogen peroxide yield. Although the exact mechanism is still not clear, the theme of the work is based on the identification of the possible active sites with the help of experimental evidence like X-ray photoelectron spectroscopy. These results support the assumption that an edge N (pyridinic N)-bonded adjacent C lowers the activation energy barriers of O₂ adsorption, predominantly to kinetically facilitate the ORR activity. We hope these results will be helpful in developing more efficient ORR catalysts.