Preparation of polypyrrole/nanosilica composite for solid-phase microextraction of bisphenol and phthalates migrated from containers to eye drops and injection solutions

This paper describes the electrodeposition of polyphosphate-doped polypyrrole/nanosilica nanocomposite coating on steel wire for direct solid-phase microextraction of bisphenol A and five phthalates. We optimized influencing parameters on the extraction efficiency and morphology of the nanocomposite such as deposition potential, concentration of pyrrole and polyphosphate, deposition time and the nanosilica amount. Under the optimized conditions, characterization of the nanocomposite was investigated by scanning electron microscopy and Fourier transform infra-red spectroscopy. Also, the factors related to the solid-phase microextraction method including desorption temperature and time, extraction temperature and time, ionic strength and pH were studied in detail. Subsequently, the proposed method was validated by gas chromatography-mass spectrometry by thermal desorption and acceptable figures of merit were obtained. The linearity of the calibration curves was between 0.01 and 50 ng/mL with acceptable correlation coefficients (0.9956-0.9987) and limits of detection were in the range 0.002-0.01 ng/mL. Relative standard deviations in terms of intra-day and inter-day by five replicate analyses from aqueous solutions containing 0.1 ng/mL of target analytes were in the range 3.3%-5.4% and 5%-7.1%, respectively. Fiber-to-fiber reproducibilities were measured for three different fibers prepared in the same conditions and the results were between 7.3% and 9.8%. Also, extraction recoveries at two different concentrations were ≥96%. Finally, the suitability of the proposed method was demonstrated through its application to the analysis of some eye drops and injection solutions.

A novel sorbent based on carbon nanotube/amino-functionalized sol-gel for the headspace solid-phase microextraction of α-bisabolol from medicinal plant samples using experimental design

A novel sol-gel coating on a stainless-steel fiber was developed for the first time for the headspace solid-phase microextraction and determination of α-bisabolol with gas chromatography and flame ionization detection. The parameters influencing the efficiency of solid-phase microextraction process, such as extraction time and temperature, pH, and ionic strength, were optimized by the experimental design method. Under optimized conditions, the linear range was between 0.0027 and 100 μg/mL. The relative standard deviations determined at 0.01 and 1.0 μg/mL concentration levels (n = 3), respectively, were as follows: intraday relative standard deviations 3.4 and 3.3%; interday relative standard deviations 5.0 and 4.3%; and fiber-to-fiber relative standard deviations 6.0 and 3.5%. The relative recovery values were 90.3 and 101.4% at 0.01 and 1.0 μg/mL spiking levels, respectively. The proposed method was successfully applied to various real samples containing α-bisabolol.

Magnetic solid-phase extraction using a mixture of two types of nanoparticles followed by gas chromatography-mass spectrometry for the determination of six phthalic acid esters in various water samples

A mixture of Fe₃O₄@MIL-100 and Fe₃O₄@SiO₂@polythiophene nanoparticles exhibit high extraction efficiency for PAEs in water.

Application of nanocomposite-based sorbents in microextraction techniques: a review

This review provides a general overview of the recent trends for the preparation of nanocomposites and their applications in microextraction techniques.

Poly(o-anisidine)/graphene oxide nanosheets composite as a coating for the headspace solid-phase microextraction of benzene, toluene, ethylbenzene and xylenes

A poly(o-anisidine)/graphene oxide nanosheets (PoA/GONSs) coating is fabricated by a simple and efficient electrochemical deposition method on steel wire. The incorporation of PoA and GONSs allows preparing a nanocomposite that can successfully integrate the advantages of both. Then, the prepared fiber is applied to the headspace solid-phase microextraction (HS-SPME) and gas chromatographic analysis of benzene, toluene, ethylbenzene and xylenes. In order to obtain an adherent, stable and efficient fiber to extract target analytes, experimental parameters related to the coating process such as deposition potential, deposition time, concentration of the monomer and concentration of GONSs were studied. The prepared composite fiber were characterized by Fourier transform infrared spectroscopy, powder X-ray diffraction and scanning electron microscopy. The effect of various parameters on the efficiency of HS-SPME process consisting of desorption temperature and time, extraction temperature and time and ionic strength were also optimized. Under the optimal conditions, the method was linear for orders of magnitude with correlation coefficients varying from 0.9888 to 0.9993. Intra- and inter-day precisions of the method were determined from mixed aqueous solutions containing 5.0 ng mL(-1) of each BTEX. The intra-day precisions varied from 3.1% for toluene to 5.7% for ethylbenzene, while the inter-day precisions varied from 4.9% for o-xylene to 7.3% for m,p-xylene. Limits of detection were in the range 0.01-0.06 ng mL(-1). The proposed method was applied to monitor BTEX compounds in some water samples and the accuracies found through spiking river water samples showed high recoveries between 92.0 and 101.2%.