Enhancing the Washing Durability and Electrical Longevity of Conductive Polyaniline-Grafted Polyester Fabrics

The demand for wearable electronics has driven the development of conductive fabrics, particularly those incorporating polyaniline (PANI) that is known for its high electrical conductivity, flexibility, and ease of fabrication. However, the limited stability and durability of the conductive fabric, especially during washing, present significant challenges. The drawbacks can be traced by weak physical attachment between the fabric and the conductive coating, leading to a decrease in conductivity over time. These drawbacks significantly impact the fabric's functionality and performance, highlighting the need for effective solutions to enhance its stability and durability. This study focuses on addressing these challenges by employing a thermochemical treatment. A hydrophilic surface of the polyester fabric is obtained after the treatment (hydrolysis), followed by grafting of PANI on it. The adhesion between PANI and the polyester fabrics was found to be enhanced, as proved by contact angle analysis. Furthermore, the PANI-hydrolyzed fabrics (treated) demonstrated stable conductivity (∼10-3 S cm-3) even after 10 washing cycles, showcasing their excellent durability. In comparison, the unhydrolyzed PANI fabric experienced a drop in conductivity by three orders of magnitude. X-ray photoelectron spectroscopy via N 1s core line spectra showed chemical shifts and quantified the level of doping through PANI's protonation level. We found that PANI-hydrolyzed fabrics preserved their dedoping level from 44.77 to 42.68%, indicating improved stability and extension of their electrical properties' lifetime after washing as compared to unhydrolyzed (untreated) fabrics, from 36.99 to 26.61%. This investigation demonstrates that the thermochemical approach can effectively enhance the durability of conductive PANI fabrics, enabling them to withstand the washing process while preserving their electrical endurance.

A review on algal biosorbents for heavy metal remediation with different adsorption isotherm models

Biosorbent composites like chitin, alginate, moss, xanthene, and cotton can be derived from biotic species such as plants, algae, fungi, and bacteria which can be used for the exclusion of both organic and inorganic toxicants from sewage, industrial effluent, polluted soils, and many more. The use of composites in place of raw substrates like alginate and chitin increases the adsorption capacity as CS₄CPL₁ beads increase the adsorption capacity for copper and nickel from 66.7 mg/g and 15.3 mg/g in the case of alginate microsphere to 719.38 mg/g and 466.07 mg/g respectively. Biosorbent fabricated from algae Chlorella vulgaris having surface area of 12.1 m²/g and pore size of 13.7 nm owing to which it displayed a higher adsorption capacity for Pb 0.433 mmol/g indicating their potential as an efficient biosorbent material. This article contains detailed information related to heavy metals as well as biosorbent that includes different isotherms, kinetics, techniques to estimate heavy metal concentration, removal methods, and adverse health effects caused due to heavy metal pollution. Apart from the above recovery and reuse of biosorbent, correlation with the sustainable development goals has also been included.

Review of manufacturing three-dimensional-printed membranes for water treatment

With the exacerbation of industrialization, water treatment has become a necessary step for the eradication of dyes, heavy metals, oils, pharmaceuticals, and illicit drugs. These pollutants pose an impending threat to the health of humans by causing chronic or acute poisoning. Albeit they are noxious, the presence of some metals in lower concentrations is indispensable for human health. 3D printing (additive manufacturing) (3DP) can contrive nearly any complicated geometric form in a wide array of objects among various scales by a layer-wise method of manufacturing, which is more indubitably designed than any other conventional method. 3DP could remodel the existing patterns of membrane housing and possibly trim down the power demand and chemical use in saltwater desalinating and wastewater purification plants. Membranes that are 3D printed with correctly arranged apertures and shapes enhance material transport and flow athwart the surface of the membrane and at once lessen membrane soiling. This kind of technology forges membranes of polymers, biopolymers, alloys, metals, and ceramics via computer-aided design (CAD). A polylactic acid porous super-hydrophobic membrane with pore size in the range 40-600 μm showed 99.4% oil-water separating power and 60 kL h^-1 m^-2 flux when the pore size was tuned to 250 μm via CAD-aided 3D printing technology. This review focuses on the ability of 3D-printed membranes for the efficient removal of toxic pollutants from wastewater. Graphical abstract 3D-printed membranes for water treatment.

Metallization of electrospun PAN nanofibers via electroless gold plating

An electroless gold plating process was investigated for the metallization of an electropun PAN fibre by utilizing a non-cyanide based gold complex i.e. gold thiosulfate.