Effect of Microstructures of Carbon Nanoproducts Grown on Carbon Fibers on the Interfacial Properties of Epoxy Composites

Two kinds of carbon nanoproducts with different microstructures, namely, carbon nanotubes (CNTs) and carbon nanofibers (CNFs), were grown on the surface of carbon fibers (CFs) by chemical vapor deposition (CVD) at low temperatures to improve the interface bonding between fibers and resins. The short-beam method and the micro-debonding method were used to test the interlaminar shear strength (ILSS) and interfacial shear strength (IFSS) of the composites. The results showed that the contribution of CNTs to the improvement of interfacial properties was better than that of CNFs. Specifically, the ILSS and IFSS of the CF-CNFs/epoxy composites increased by 18.59 and 24.39%, respectively, while the ILSS and IFSS of the CF-CNTs/epoxy composites increased by 26.97 and 47.79%, respectively. Compared with CNFs, the high degree of graphitization of CNTs and the π-interactions with the resin can better induce the formation of an interphase between the fiber and the resin, which suppressed the initiation of cracks and extended the propagation path of the cracks in the composites.

Meso- and macroporous silica-based arsenic adsorbents: effect of pore size, nature of the active phase, and silicon release

Arsenic pollution in ground and drinking water is a major problem worldwide due to the natural abundance of arsenic by dissolution from ground sediment or mining activities from anthropogenic activities. To overcome this issue, iron oxides as low-cost and non-toxic materials, have been widely studied as efficient adsorbents for arsenic removal, including when dispersed within porous silica supports. In this study, two head-to-head comparisons were developed to highlight the As(v)-adsorptive ability of meso- and macrostructured silica-based adsorbents. First, the role of the textural properties of a meso-(SBA15) and macrostructured (MOSF) silica support in affecting the structural-morphological features and the adsorption capacity of the active phase (Fe2O3) have been studied. Secondly, a comparison of the arsenic removal ability of inorganic (Fe2O3) and organic (amino groups) active phases was carried out on SBA15. Finally, since silica supports are commonly proposed for both environmental and biomedical applications as active phase carriers, we have investigated secondary silicon and iron pollution. The batch tests at different pH revealed better performance from both Fe2O3-composites at pH 3. The values of q m of 7.9 mg g-1 (53 mg gact -1) and 5.5 mg g-1 (37 mg gact -1) were obtained for SBA15 and MOSF, respectively (gact stands for mass of the active phase). The results suggest that mesostructured materials are more suitable for dispersing active phases as adsorbents for water treatment, due to the obtainment of very small Fe2O3 NPs (about 5 nm). Besides studying the influence of the pore size of SBA15 and MOSF on the adsorption process, the impact of the functionalization was analyzed on SBA15 as the most promising sample for As(v)-removal. The amino-functionalized SBA15 adsorbent (3-aminopropyltriethoxysilane, APTES) exhibited a q m of 12.4 mg g-1 and faster kinetics. Furthermore, issues associated with the release of iron and silicon during the sorption process, causing secondary pollution, were evaluated and critically discussed.

Nondestructive Strategy to Effectively Enhance the Interfacial Adhesion of PBO/Epoxy Composites

Low interfacial adhesion seriously limits the wide application of PBO fiber in composites. To solve this problem, a novel hierarchical reinforcement strategy was developed by introducing epoxy sizing, nanoreinforcement of amino-functionalized silicon dioxide (SiO₂-NH₂), and an interfacial compatibilizer of 2,6-bis(2-hydroxy-4-aminophenyl) benzobisoxazole (HABO) onto poly(p-phenylene benzobisoxazole) (PBO) fibers via a facile dip-coating approach. SiO₂-NH₂ and HABO were uniformly dispersed in epoxy sizing, forming an active interface layer. On this basis, wettability, surface roughness of the PBO fiber, and compatibility with the resin matrix were significantly improved, which gave 88.4 and 40.4% enhancement in the interfacial shear strength and interlaminar shear strength of the corresponding composites, respectively. Moreover, it should be noted that the outstanding mechanical and thermal properties of the PBO fiber were not impaired during the sizing treatment. In summary, our work provides an effective and damage-free approach to improve the interfacial adhesion of PBO/epoxy composites.

Facile Strategy of Improving Interfacial Strength of Silicone Resin Composites Through Self-Polymerized Polydopamine Followed via the Sol-Gel Growing of Silica Nanoparticles onto Carbon Fiber

In the present research, to enhance interfacial wettability and adhesion between carbon fibers (CFs) and matrix resin, hydrophilic silica nanoparticles (SiO₂) were utilized to graft the surface of CFs. Polydopamine (PDA) as a "bio-glue" was architecturally built between SiO₂ and CFs to obtain a strong adhesion strength and homogenous SiO₂ distribution onto the surface of CFs. The facile modification strategy was designed by self-polymerization of dopamine followed by the hydrolysis of tetraethoxysilane (TEOS) onto carbon fibers. Surface microstructures and interfacial properties of CFs, before and after modification, were systematically investigated. The tight and homogeneous coverage of SiO₂ layers onto the CF surface, with the assistance of a PDA layer by self-polymerization of dopamine, significantly enhanced fiber surface roughness and wettability, resulting in an obvious improvement of mechanical interlocking and interfacial interactions between CFs and matrix resin. The interlaminar shear strength (ILSS) and the interfacial shear strength (IFSS) of CF/PDA/SiO₂ reinforced composites exhibited 57.28% and 41.84% enhancements compared with those of untreated composites. In addition, impact strength and the hydrothermal aging resistance of the resulting composites showed great improvements after modification. The possible reinforcing mechanisms during the modification process have been discussed. This novel strategy of developed SiO₂-modified CFs has interesting potential for interfacial improvements for advanced polymer composites.

Roll-to-Roll Processing of Silicon Carbide Nanoparticle-Deposited Carbon Fiber for Multifunctional Composites

This work provides a proof of principle that a high volume, continuous throughput fiber coating process can be used to integrate semiconducting nanoparticles on carbon fiber surfaces to create multifunctional composites. By embedding silicon carbide nanoparticles in the fiber sizing, subsequent composite fabrication methods are used to create unidirectional fiber-reinforced composites with enhanced structural health monitoring (SHM) sensitivity and increased interlaminar strength. Additional investigations into the mechanical damping behavior of these functional composites reveal a significantly increased loss factor at the glass-transition temperature ranging from a 65 to 257% increase. Composites with both increased interlaminar strength and SHM sensitivity are produced from a variety of epoxy and silicon carbide nanoparticle concentrations. Overall, the best performing composite in terms of combined performance shows an increase of 47.5% in SHM sensitivity and 7.7% increase in interlaminar strength. This work demonstrates successful and efficient integration of nanoparticle synthesis into large-scale, structural applications.

Light triggered interfacial damage self-healing of poly(p-phenylene benzobisoxazole) fiber composites

The interfacial microcracks in the resin matrix composites are difficult to be detected and repaired. However, the self-healing concept provides opportunities to fabricate composites with unusual properties. In the present study, photothermal conversion Ag-Cu₂S nanoparticles were immobilized onto poly(p-phenylene benzobisoxazole) (PBO) fibers via a polydopamine chemistry. Benefitting from the photothermal effects of Ag-Cu₂S, the obtained PBO fibers (Ag-Cu₂S-PBO) efficiently converted the light energy into heat under Xenon lamp irradiation. Then, single PBO fiber composites were prepared using thermoplastic polyurethane as the matrix. It was found that the interfacial damage caused by single fiber pull-out was simply self-healed by Xe light irradiation. This wonderful interfacial damage self-healing property was mainly attributed to the in situ heating generation via photothermal effects of Ag-Cu₂S in the composite interface. This paper reports a novel strategy to construct advanced composites with light-triggered self-healing properties, which will provide inspiration for preparing high performance composite materials.

Interfacial properties and thermo-oxidative stability of carbon fiber reinforced methylphenylsilicone resin composites modified with polyhedral oligomeric silsesquioxanes in the interphase

The grafting of trisilanolphenyl-polyhedral oligomeric silsesquioxanes (trisilanolphenyl-POSS) onto carbon fibers (CFs) was achieved using toluene-2,4-diisocyanate (TDI) as the bridging agent.

Interfacially reinforced carbon fiber/epoxy composites by grafting melamine onto carbon fibers in supercritical methanol

Carbon fiber was firstly functionalized with melamine in supercritical methanol to improve the properties of CF reinforced epoxy composites.