A simple method to control the formation of cerium phosphate architectures

Nucleation kinetics of lithium phosphate precipitation

Fourth-order kinetics arises from the consecutive complexation leading to precipitation.

Label-free wide range electrochemical detection of β-carotene using solid state assisted synthesis of hexagonal boron nitride nanosheets

Label-free, ultra-selective sensing of β-carotene using hBN nanosheets.

Lactic-acid enhanced solvothermal crystallization, color-tunable photoluminescence, and thermal stability of h-LaPO4:Ce3+, Tb3+, Sm3+ nanocrystals

Color-tunable photoluminescence of h-(La_0.93−xCe_0.05Tb_xSm_0.02)PO₄ nanocrystals.

Flow-driven crystal growth of lithium phosphate in microchannels

Flow-driven asymmetric growth of lithium phosphate in the presence of concentration gradients in a microchannel.

Hierarchically three-dimensional (3D) nanotubular sea urchin-shaped iron oxide and its application in heavy metal removal and solar-induced photocatalytic degradation

In this study, hierarchically three-dimensional (3D) nanotubular sea urchin-shaped iron oxide nanostructures (3D-Fe₂O₃) were synthesized by a facile and rapid ultrasound irradiation method. Additives, templates, inert gas atmosphere, pH regulation, and other complicated procedures were not required. Dense 3D-Fe₂O₃ with a relatively large Brunauer-Emmett-Teller (BET) surface area of 129.4 m²/g was synthesized within 23 min, and the BET surface area was further improved to 282.7 m²/g by a post heat-treatment process. In addition, this post processing led to phase changes from maghemite (γ phase) to hematite (α phase) Fe₂O₃. Subsequent characterization suggested that the growth mechanism of the 3D-Fe₂O₃ follows self-assembly and oriented attachment. The prepared 3D-Fe₂O₃ was applied to wastewater purification. Ultrasound-irradiated 3D-Fe₂O₃ can eliminate a As(V) and Cr(VI) from water with 25 times faster removal rate by using a one third smaller amount than commercial α-Fe₂O₃. This was attributed to the inter-particle pores and relatively positively charged surface of the nanostructure. In addition, post heat treatment on ultrasound-irradiated 3D-Fe₂O₃ significantly influenced the photocatalytic degradation of methylene blue and phenol, with a 25 times higher removal efficiency than that of commercial α-Fe₂O₃, because of both high BET surface area and good crystallization of the prepared samples.

A highly stable indium based metal organic framework for efficient arsenic removal from water

Indium based metal organic framework crystals (AUBM-1) were successfully synthesized via a solvothermal synthesis process. SXRD analysis showed the production of a new In-MOF structure with a pts topology. AUBM-1 was shown to be chemically stable and was used as an adsorbent to efficiently remove arsenic from water.

Transcription of Nanofibrous Cerium Phosphate Using a pH-Sensitive Lipodipeptide Hydrogel Template

A novel and simple transcription strategy has been designed for the template-synthesis of CePO₄·xH₂O nanofibers having an improved nanofibrous morphology using a pH-sensitive nanofibrous hydrogel (glycine-alanine lipodipeptide) as structure-directing scaffold. The phosphorylated hydrogel was employed as a template to direct the mineralization of high aspect ratio nanofibrous cerium phosphate, which in-situ formed by diffusion of aqueous CeCl₃ and subsequent drying (60 °C) and annealing treatments (250, 600 and 900 °C). Dried xerogels and annealed CePO₄ powders were characterized by conventional thermal and thermogravimetric analysis (DTA/TG), and Wide-Angle X-ray powder diffraction (WAXD) and X-ray powder diffraction (XRD) techniques. A molecular packing model for the formation of the fibrous xerogel template was proposed, in accordance with results from Fourier-Transformed Infrarred (FTIR) and WAXD measurements. The morphology, crystalline structure and composition of CePO₄ nanofibers were characterized by electron microscopy techniques (Field-Emission Scanning Electron Microscopy (FE-SEM), Transmission Electron Microscopy/High-Resolution Transmission Electron Microscopy (TEM/HRTEM), and Scanning Transmission Electron Microscopy working in High Angle Annular Dark-Field (STEM-HAADF)) with associated X-ray energy-dispersive detector (EDS) and Scanning Transmission Electron Microscopy-Electron Energy Loss (STEM-EELS) spectroscopies. Noteworthy, this templating approach successfully led to the formation of CePO₄·H₂O nanofibrous bundles of rather co-aligned and elongated nanofibers (10⁻20 nm thick and up to ca. 1 μm long). The formed nanofibers consisted of hexagonal (P6₂22) CePO₄ nanocrystals (at 60 and 250 °C), with a better-grown and more homogeneous fibrous morphology with respect to a reference CePO₄ prepared under similar (non-templated) conditions, and transformed into nanofibrous monoclinic monazite (P21/n) around 600 °C. The nanofibrous morphology was highly preserved after annealing at 900 °C under N₂, although collapsed under air conditions. The nanofibrous CePO₄ (as-prepared hexagonal and 900 °C-annealed monoclinic) exhibited an enhanced UV photo-luminescent emission with respect to non-fibrous homologues.

Flow Control of A+B→C Fronts by Radial Injection

The dynamics of A+B→C fronts is analyzed theoretically in the presence of passive advection when A is injected radially into B at a constant inlet flow rate Q. We compute the long-time evolution of the front position, r_{f}, of its width, w, and of the local production rate R of the product C at r_{f}. We show that, while advection does not change the well-known scaling exponents of the evolution of corresponding reaction-diffusion fronts, their dynamics is however significantly influenced by the injection. In particular, the total amount of product varies as Q^{-1/2} for a given volume of injected reactant and the front position as Q^{1/2} for a given time, paving the way to a flow control of the amount and spatial distribution of the reaction front product. This control strategy compares well with calcium carbonate precipitation experiments for which the amount of solid product generated in flow conditions at fixed concentrations of reactants and the front position can be tuned by varying the flow rate.

Flow-driven morphology control in the cobalt–oxalate system

The presence of fluid flow by maintaining the density gradient and controlling the flow rate provides a simple method to modify the microstructure of cobalt oxalate.