Multiscale morphology design of hybrid halide perovskites through a polymeric template

Crystallinity Control and Strain Release in Wide-Bandgap Perovskite Film via Seed-Induced Growth for Efficient Photovoltaics

The seed method stands out as a straightforward and efficient approach for fabricating high-performance perovskite solar cells (PSCs). In this study, we propose the utilization of an antisolvent as an additive to induce crystal seeding, thereby facilitating the growth of wide-bandgap perovskite grains. Specifically, we introduce three commonly used antisolvents─ethyl acetate (EA), isopropanol (IPA), and chlorobenzene (CB)─directly into the perovskite precursor solution to generate perovskite seeds, which serve to promote subsequent nucleation. This antisolvent-crystal seeding method (ACSM) results in increased grain sizes, reduced film defects, and overall improved film quality. Consequently, the power conversion efficiencies (PCEs) of 1.647 eV PSCs with EA, IPA, and CB additives are recorded at 19.86%, 20.61%, and 20.45%, respectively, surpassing that of the reference device with a PCE of 18.83%. Furthermore, the stability of the PSCs prepared through ACSM is notably enhanced. Notably, PSCs optimized with IPA retain 75% of the original PCE after being stored in ambient air conditions (25 °C, RH ∼ 15%) for 30 days, better than the CB-added (64%) and the EA-added devices (53%), while the reference devices only retain 31% of the initial PCE. Moreover, even after continuous thermal annealing at 50 °C for 200 h, IPA-assisted devices demonstrate the best stability, followed by those with CB and EA, with the reference exhibiting the poorest stability.

Simultaneous achievement of defect passivation and carrier transport promotion by using emerald salt for methylammonium-free perovskite solar cells

Defect passivation along with promoted charge transport is potentially an effective but seldom exploited strategy for high-performance perovskite solar cells (PSCs). Herein, the in situ defect passivation and carrier transport improvement are simultaneously realized by introducing a conductive polymer (i.e., emerald salt, ES) into the precursor solution of methylammonium (MA)-free perovskites. The interaction between ES and uncoordinated Pb2+ reduces defect density to suppress the non-radiative recombination. Moreover, ES can act as a "carrier driver" to promote the carrier transport due to its conductive feature, resulting in efficient PSC devices with a decent power conversion efficiency (PCE) of 23.0%, which is among the most efficient MA-free PSCs. The ES-based unencapsulated devices show superior stability, retaining 89.1% and 83.8% of their initial PCEs when subjected to 35 ± 5% relative humidity (RH) storage and 85 °C thermal aging for 1000 h, respectively. To further assess the large-area compatibility of our strategy, 5 × 5 cm2 mini modules were also fabricated, delivering an impressive efficiency of 19.3%. This work sheds light on the importance of conductive additives in boosting cell performance by playing multiple roles in passivating defects, retarding the moisture invasion, and enhancing and balancing charge transport.

Exploring Nanoscale Structure in Perovskite Precursor Solutions Using Neutron and Light Scattering

Tailoring the solution chemistry of metal halide perovskites requires a detailed understanding of precursor aggregation and coordination. In this work, we use various scattering techniques, including dynamic light scattering (DLS), small angle neutron scattering (SANS), and spin-echo SANS (SESANS) to probe the nanostructures from 1 nm to 10 μm within two different lead-halide perovskite solution inks (MAPbI₃ and a triple-cation mixed-halide perovskite). We find that DLS can misrepresent the size distribution of the colloidal dispersion and use SANS/SESANS to confirm that these perovskite solutions are mostly comprised of 1-2 nm-sized particles. We further conclude that if there are larger colloids present, their concentration must be <0.005% of the total dispersion volume. With SANS, we apply a simple fitting model for two component microemulsions (Teubner-Strey), demonstrating this as a potential method to investigate the structure, chemical composition, and colloidal stability of perovskite solutions, and we here show that MAPbI₃ solutions age more drastically than triple cation solutions.

Polymer-Assisted Single-Step Slot-Die Coating of Flexible Perovskite Solar Cells at Mild Temperature from Dimethyl Sulfoxide

The industrialization of perovskite solar cells relies on solving intrinsic-to-material issues. To reach record efficiencies perovskite deposition needs to be finely adjusted by multi-step processes, in a humidity free glove-box environment and by means of hardly scalable techniques often associated with toxic solvents and anti-solvent dripping/bath. Herein, the use of polymeric material is proposed to deposit perovskite layers with easy processability. To the scope, a starch-polymer/perovskite composite is developed to suit slot-die coating technique requirement, allowing the deposition of hybrid halide perovskite material in a single straightforward step without the use of toxic solvents, and in uncontrolled humid environment (RH up to 70 %). The starch-polymer increases the viscosity of the perovskite precursor solutions and delays the perovskite crystallization that results in the formation of perovskite films at mild temperature (60 °C) with good morphology. These innovative inks enables the fabrication of flexible solar cells with p-i-n configuration featured by a power conversion efficiency higher than 3 %. . Overall, this approach can be exploited in the future to massively reduce perovskite manufacturing costs related to keeping the entire fabrication line at high-temperature and under nitrogen or dry conditions.

The Contribution of NMR Spectroscopy in Understanding Perovskite Stabilization Phenomena

Although it has been exploited since the late 1900s to study hybrid perovskite materials, nuclear magnetic resonance (NMR) spectroscopy has only recently received extraordinary research attention in this field. This very powerful technique allows the study of the physico-chemical and structural properties of molecules by observing the quantum mechanical magnetic properties of an atomic nucleus, in solution as well as in solid state. Its versatility makes it a promising technique either for the atomic and molecular characterization of perovskite precursors in colloidal solution or for the study of the geometry and phase transitions of the obtained perovskite crystals, commonly used as a reference material compared with thin films prepared for applications in optoelectronic devices. This review will explore beyond the current focus on the stability of perovskites (3D in bulk and nanocrystals) investigated via NMR spectroscopy, in order to highlight the chemical flexibility of perovskites and the role of interactions for thermodynamic and moisture stabilization. The exceptional potential of the vast NMR tool set in perovskite structural characterization will be discussed, aimed at choosing the most stable material for optoelectronic applications. The concept of a double-sided characterization in solution and in solid state, in which the organic and inorganic structural components provide unique interactions with each other and with the external components (solvents, additives, etc.), for material solutions processed in thin films, denotes a significant contemporary target.

Inclusion of 2D Transition Metal Dichalcogenides in Perovskite Inks and Their Influence on Solar Cell Performance

Organic–inorganic hybrid perovskite materials have raised great interest in recent years due to their excellent optoelectronic properties, which promise stunning improvements in photovoltaic technologies. Moreover, two-dimensional layered materials such as graphene, its derivatives, and transition metal dichalcogenides have been extensively investigated for a wide range of electronic and optoelectronic applications and have recently shown a synergistic effect in combination with hybrid perovskite materials. Here, we report on the inclusion of liquid-phase exfoliated molybdenum disulfide nanosheets into different perovskite precursor solutions, exploring their influence on final device performance. We compared the effect of such additives upon the growth of diverse perovskites, namely CH₃NH₃PbI₃ (MAPbI₃) and triple-cation with mixed halides Cs_x (MA_0.17FA_0.83)_(1−x)Pb (I_0.83Br_0.17)₃ perovskite. We show how for the referential MAPbI₃ materials the addition of the MoS₂ additive leads to the formation of larger, highly crystalline grains, which result in a remarkable 15% relative improvement in power conversion efficiency. On the other hand, for the mixed cation–halide perovskite no improvements were observed, confirming that the nucleation process for the two materials is differently influenced by the presence of MoS₂.

Implication of polymeric template agent on the formation process of hybrid halide perovskite films

The use of polymeric additives supporting the growth of hybrid halide perovskites has proven to be a successful approach aiming at high quality active layers targeting optoelectronic exploitation. A detailed description of the complex process involving the self-assembly of the precursors into the perovskite crystallites in presence of the polymer is, however, still missing. Here we take starch:CH₃NH₃PbI₃ (MAPbI₃) as example of highly performing composite, both in solar cells and light emitting diodes, and study the film formation process through differential scanning calorimetry and in situ time-resolved grazing incidence wide-angle x-ray scattering, performed during spin coating. These measurements reveal that starch beneficially influences the nucleation and growth of the perovskite precursor phase, leading to improved structural properties of the resulting film which turns into higher stability towards environmental conditions.

A multivariate approach to investigate the NMR CPMG pulse sequence for analysing low MW species in polymers

Detection and quantification of low molecular weight components in polymeric samples via nuclear magnetic resonance (NMR) spectroscopy can be difficult due to overlapping signal caused by line broadening characteristics of polymers. A way of overcoming this problem could be the exploitation of the difference in relaxation between small molecules and macromolecular species, such as the application of a T₂ filter by using the Carr-Purcell-Meiboom-Gill (CPMG) spin-echo pulse sequence. This technique, largely exploited in metabolomics studies, is applied here to material sciences. A Design of Experiments approach was used for evaluating the effect of different acquisition parameters (relaxation delay, echo time and number of cycles) and sample-related ones (concentration and polymer molecular weight) on selected responses, with a particular interest in performing a reliable quantitative analysis. Polymeric samples containing small molecules were analysed by NMR with and without the application of the filter, and analysis of variance was used to identify the most influential parameters. Results indicated that increasing the polymer concentration, hence sample viscosity, further attenuates polymer signals in CPMG experiments because the T₂ of those signals tends to decrease with increasing viscosity. The signal-to-noise ratio measured for small molecules can undergo a minimum loss when specific parameters are chosen in relation to the polymer molecular weight. Furthermore, the difference in dynamics between aliphatic and aromatic nuclei, as well as between mobile and stiff polymers, translates into different results in terms of polymer signal reduction, suggesting that the relaxation filter can also be used for obtaining information on the polymer structure.

Investigation of the exciton relaxation processes in poly(9,9-dioctylfluorene-co-benzothiadiazole):CsPbI1.5Br1.5 nanocrystal hybrid polymer–perovskite nanocrystal blend

The combination of lead halide perovskite nanocrystals and conjugated polymer in a blend film opens the way to the realization of hybrid active layers with widely tunable optical and electrical properties. However, the interaction between the polymeric and the perovskite component of the blends is mainly unexplored to date. In this work we perform temperature-dependent photoluminescence and time resolved photoluminescence measurements in order to deeply investigate the photophysics of a poly(9,9-dioctylfluorene-co-benzothiadiazole) (F8BT):CsPbI_1.5Br_1.5 nanocrystal hybrid film. Our results suggest that the primary interaction channel is charge transfer, both from F8BT to the NCs and from the NCs to F8BT, while Förster resonant energy transfer has no visible effects. Moreover, we show that the charge transfer is assisted by energy migration within the F8BT excited state distribution and that it is dependent on the local micromorphology of the film. Our work improves the current understanding of the polymer:perovskite NC interactions in hybrid films, and it is expected to be relevant for the development of hybrid organic–perovskite optoelectronic devices.

The emission properties of a hybrid polymer:perovskite nanocrystals (NCs) blend film are investigated, evidencing that the main interaction process is not Förster transfer, but instead bidirectional polymer → NC and NC → polymer charge transfer.

Static Rashba Effect by Surface Reconstruction and Photon Recycling in the Dynamic Indirect Gap of APbBr3 (A = Cs, CH3NH3) Single Crystals

Recently, halide perovskites have gained significant attention from the perspective of efficient spintronics owing to the Rashba effect. This effect occurs as a consequence of strong spin-orbit coupling under a noncentrosymmetric environment, which can be dynamic and/or static. However, there exist intense debates on the origin of broken inversion symmetry since the halide perovskites typically crystallize into a centrosymmetric structure. In order to clarify the issue, we examine both dynamic and static effects in the all-inorganic CsPbBr₃ and organic-inorganic CH₃NH₃PbBr₃ (MAPbBr₃) perovskite single crystals by employing temperature- and polarization-dependent photoluminescence excitation spectroscopy. The perovskite single crystals manifest the dynamic effect by photon recycling in the indirect Rashba gap, causing dual peaks in the photoluminescence. However, the effect vanishes in CsPbBr₃ at low temperatures (<50 K) accompanied by a striking color change of the crystal, arising presumably from lower degrees of freedom for inversion symmetry breaking associated with the thermal motion of the spherical Cs cation compared with the polar MA cation in MAPbBr₃. We also show that the static Rashba effect occurs only in MAPbBr₃ below 90 K, presumably due to surface reconstruction via MA-cation ordering, which likely extends across a few layers from the crystal surface to the interior. We further demonstrate that this static Rashba effect can be completely suppressed upon surface treatment with polymethyl methacrylate (PMMA) coating. We believe that our results provide a rationale for the Rashba effects in halide perovskites.

Nano-Micro Dimensional Structures of Fiber-Shaped Luminous Halide Perovskite Composites for Photonic and Optoelectronic Applications

Perovskite nanomaterials have been revealed as highly luminescent structures regarding their dimensional confinement. In particular, their promising potential lies behind remarkable luminescent properties, including color tunability, high photoluminescence quantum yield, and the narrow emission band of halide perovskite (HP) nanostructures for optoelectronic and photonic applications such as lightning and displaying operations. However, HP nanomaterials possess such drawbacks, including oxygen, moisture, temperature, or UV lights, which limit their practical applications. Recently, HP-containing polymer composite fibers have gained much attention owing to the spatial distribution and alignment of HPs with high mechanical strength and ambient stability in addition to their remarkable optical properties comparable to that of nanocrystals. In this review, the fabrication methods for preparing nano-microdimensional HP composite fiber structures are described. Various advantages of the luminescent composite nanofibers are also described, followed by their applications for photonic and optoelectronic devices including sensors, polarizers, waveguides, lasers, light-down converters, light-emitting diode operations, etc. Finally, future directions and remaining challenges of HP-based nanofibers are presented.

High-Quality Concentrated Precursor Solution in N,N-Dimethylformamide for Thick Methylammonium Triiodoplumbate Layer in Solar Cells

A high-quality precursor solution is essential for the fabrication of hybrid perovskite solar cells. This article reports a simple and efficient method for preparing a high-quality concentrated solution of methylammonium triiodoplumbate (MAPbI₃) in N,N-dimethylformamide (DMF) by using MAPbI₃ crystals instead of conventional lead iodine and methylammonium iodine blend. The MAPbI₃ concentration of the precursor solution is easily and accurately adjusted from 0 up to 1.64 M. An investigation of the dissolution process of the MAPbI₃ crystals reveals that the concentrated solution of MAPbI₃ in DMF is metastable, and the transition from the concentrated solution to solvated intermediate MAPbI₃·DMF determines the solubility of MAPbI₃ in DMF. The high purity and precise stoichiometric ratio of the crystals eliminate the possible impurities that initialize the transition to MAPbI₃·DMF and consequently suppress the transition and increase the stability of the concentrated solution. MAPbI₃ films with different thicknesses up to 800 nm are prepared with the conventional film fabrication technique, and the highest power conversion efficiency of 20.7% is achieved on corresponding solar cells. This newly developed method for preparing a concentrated precursor solution can be easily combined with other fabrication techniques for further development of industrial-scale manufacture of solar cells.

Simple Processing Additive-Driven 20% Efficiency for Inverted Planar Heterojunction Perovskite Solar Cells

Compositional engineering has been a strong tool to improve the quality of the perovskite materials and, in turn, the reproducibility of the solar cells. However, the control over the active layer uniformity, one of the most important requirements for the obtainment of efficient devices, is still a weak point of perovskite solar cells (PSCs) manufacturing. Here, we develop an approach to grow a uniform mixed cation perovskite layer, foreseeing its implementation in inverted solar cells endowing organic transporting layers, through the addition of a stoiochiometric amount of tropolone as chelating agent for the lead. Thanks to low melting and boiling temperatures, tropolone is present in the system only during the colloidal liquid phase, leaving the film during its formation; this unique characteristic promotes the obtainment of ideal perovskite surface morphologies and an increased short circuit current of photovoltaic devices. A maximum power conversion efficiency of 20% was obtained, with a 25% increase with respect to the reference.

Reducing Detrimental Defects for High-Performance Metal Halide Perovskite Solar Cells

In several photovoltaic (PV) technologies, the presence of electronic defects within the semiconductor band gap limit the efficiency, reproducibility, as well as lifetime. Metal halide perovskites (MHPs) have drawn great attention because of their excellent photovoltaic properties that can be achieved even without a very strict film-growth control processing. Much has been done theoretically in describing the different point defects in MHPs. Herein, we discuss the experimental challenges in thoroughly characterizing the defects in MHPs such as, experimental assignment of the type of defects, defects densities, and the energy positions within the band gap induced by these defects. The second topic of this Review is passivation strategies. Based on a literature survey, the different types of defects that are important to consider and need to be minimized are examined. A complete fundamental understanding of defect nature in MHPs is needed to further improve their optoelectronic functionalities.

Heterostructural CsPbX3-PbS (X = Cl, Br, I) Quantum Dots with Tunable Vis-NIR Dual Emission

Perovskite and chalcogenide quantum dots (QDs) are important nano semiconductors. It has been a challenge to synthesize heterostructural QDs combining perovskite and chalcogenide with tailorable photoelectronic properties. In this report, heterostructural CsPbX₃-PbS (X = Cl, Br, I) QDs were successfully synthesized via a room temperature in situ transformation route. The CsPbX₃-PbS QDs show a tunable dual emission feature with the visible and near-infrared (NIR) photoluminescence (PL) corresponding to CsPbX₃ and PbS, respectively. Typically, the formation and evolution of the heterostructural CsPbBr₃-PbS QDs with reaction time was investigated. Femtosecond transient absorption spectroscopy (TAS) was applied to illuminate the exciton dynamics in CsPbBr₃-PbS QDs. The mild synthetic method and TAS proved perovskite to PbS energy transfer may pave the way toward highly efficient QD photovoltaic and optoelectronic devices.

Optimizing the Interface between Hole Transporting Material and Nanocomposite for Highly Efficient Perovskite Solar Cells

The performances of organometallic halide perovskite-based solar cells severely depend on the device architecture and the interface between each layer included in the device stack. In particular, the interface between the charge transporting layer and the perovskite film is crucial, since it represents both the substrate where the perovskite polycrystalline film grows, thus directly influencing the active layer morphology, and an important site for electrical charge extraction and/or recombination. Here, we focus on engineering the interface between a perovskite-polymer nanocomposite, recently developed by our group, and different commonly employed polymeric hole transporters, namely PEDOT: PSS [poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)], PEDOT, PTAA [poly(bis 4-phenyl}{2,4,6-trimethylphenyl}amine)], Poly-TPD [Poly(N,N'-bis(4-butylphenyl)-N,N'-bis(phenyl)-benzidine] Poly-TPD, in inverted planar perovskite solar cell architecture. The results show that when Poly-TPD is used as the hole transfer material, perovskite film morphology improved, suggesting an improvement in the interface between Poly-TPD and perovskite active layer. We additionally investigate the effect of the Molecular Weight (MW) of Poly-TPD on the performance of perovskite solar cells. By increasing the MW, the photovoltaic performances of the cells are enhanced, reaching power conversion efficiency as high as 16.3%.

Stretchable and Ambient Stable Perovskite/Polymer Luminous Hybrid Nanofibers of Multicolor Fiber Mats and Their White LED Applications

We report the fabrication and optical/mechanical properties of perovskite/thermoplastic polyurethane (TPU)-based multicolor luminescent core-shell nanofibers and their large-scale fiber mats. One-step coaxial perovskite/TPU nanofibers had a high photoluminescence quantum yield value exceeding 23.3%, surpassing that of its uniaxial counterpart, due to the homogeneous distribution of perovskite nanoparticles (NPs) by the confinement of the TPU shell. The fabricated core-shell nanofibers exhibited a high mechanical endurance owing to the well elastic properties of TPU and maintained the luminescence intensity even under a 100% stretched state after 1000 stretching-relaxing cycles. By taking advantage of the hydrophobic nature of TPU, the ambient and moisture stability of the fabricated fibers were enhanced up to 1 month. Besides, large-area stretchable nanofibers with a dimension of 15 cm × 30 cm exhibiting various visible-light emission peaks were fabricated by changing the composition of perovskite NPs. Moreover, a large-scale luminescent and stretchable fiber mat was successfully fabricated by electrospinning. Furthermore, the white-light emission from the fabricated fibers and mats was achieved by incorporating orange-light-emitting poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] into the TPU shell and coupling the turquoise blue-light-emitting perovskite NPs in the core site. Finally, the integrity of the perovskite-based TPU fibers was realized by fabricating a light-emitting diode (LED) device containing the orange-light-emitting fibers embedded in the polyfluorene emissive layer. This work demonstrated an effective way to prepare stable and stretchable luminous nanofibers and the integration of such nanofibers into LED devices, which could facilitate the future development of wearable electronic devices.

A novel graphene oxide/trans-1,4-polyisoprene (GO/TPI) shape memory polymer nanocomposite and its multifunctional properties

In this work, we have synthesized a novel graphene oxide/trans-1,4-polyisoprene (GO/TPI) shape memory polymer (SMP) nanocomposite by adding GO (0.0-1.5 phr) to bulk TPI polymer to enhance its mechanical properties. We have studied and examined its mechanical, thermal and thermomechanical properties through systematic tests from microscale to macroscale. The shape memory properties and the effect of the GO content on the thermal and mechanical properties of the manufactured SMP nanocomposites were studied by differential scanning calorimetry, dynamic mechanical analysis, thermogravimetric analysis, thermal conductivity, and static tensile and mechanical as well as thermomechanical cyclic loading tests. The experimental results indicate that the SMP nanocomposite with 0.9 phr GO has superior thermal and mechanical properties compared to all other cases, and good shape memory was obtained in the GO/TPI nanocomposites.

Pb clustering and PbI2 nanofragmentation during methylammonium lead iodide perovskite degradation

Studying defect formation and evolution in MethylAmmonium lead Iodide (MAPbI₃) perovskite layers has a bottleneck in the softness of the matter and in its consequent sensitivity to external solicitations. Here we report that, in a polycrystalline MAPbI₃ layer, Pb-related defects aggregate into nanoclusters preferentially at the triple grain boundaries as unveiled by Transmission Electron Microscopy (TEM) analyses at low total electron dose. Pb-clusters are killer against MAPbI₃ integrity since they progressively feed up the hosting matrix. This progression is limited by the concomitant but slower transformation of the MAPbI₃ core to fragmented and interconnected nano-grains of 6H-PbI₂ that are structurally linked to the mother grain as in strain-relaxed heteroepitaxial coupling. The phenomenon occurs more frequently under TEM degradation whilst air degradation is more prone to leave uncorrelated [001]-oriented 2H-PbI₂ grains as statistically found by X-Ray Diffraction. This path is kinetically costlier but thermodynamically favoured and is easily activated by catalytic species.

Methylammonium lead halide perovskites have great potential for optoelectronic applications but are prone to degradation. Here the authors show that degradation can occur through clustering of Pb containing defects at the grain boundaries while concurrent formation of PbI₂ blocks further reactions, suggesting a strategy for passivation.

The Applications of Polymers in Solar Cells: A Review

The emerging dye-sensitized solar cells, perovskite solar cells, and organic solar cells have been regarded as promising photovoltaic technologies. The device structures and components of these solar cells are imperative to the device’s efficiency and stability. Polymers can be used to adjust the device components and structures of these solar cells purposefully, due to their diversified properties. In dye-sensitized solar cells, polymers can be used as flexible substrates, pore- and film-forming agents of photoanode films, platinum-free counter electrodes, and the frameworks of quasi-solid-state electrolytes. In perovskite solar cells, polymers can be used as the additives to adjust the nucleation and crystallization processes in perovskite films. The polymers can also be used as hole transfer materials, electron transfer materials, and interface layer to enhance the carrier separation efficiency and reduce the recombination. In organic solar cells, polymers are often used as donor layers, buffer layers, and other polymer-based micro/nanostructures in binary or ternary devices to influence device performances. The current achievements about the applications of polymers in solar cells are reviewed and analyzed. In addition, the benefits of polymers for solar cells, the challenges for practical application, and possible solutions are also assessed.

Influence of polymeric electrets on the performance of derived hybrid perovskite-based photo-memory devices

Organic-inorganic hybrid perovskite has become one of the most important photoactive materials owing to its intense light-harvesting property as well as its facile solution processability. Besides its photovoltaic applications, a novel photo-programmed transistor memory was recently developed based on the device architecture of a floating-gate transistor memory using a polymer/perovskite blend as the gate dielectric with the non-volatile memory characteristics of decent light response, applicable On/Off current ratio, and long retention time. In this study, we further clarify the influence of polymer matrix selection on the photo-response and memory properties of derived hybrid perovskite-based photo-memory devices. Four different host polymers, polystyrene (PS), poly(4-vinylphenol) (PVPh), poly(methyl methacrylate) (PMMA), and poly(methacrylic acid) (PMAA), were systematically investigated for comparison herein. This revealed that dissimilar chemical interactions existed between the host polymers and perovskite, resulting in the distinct memory behavior of the derived photo-memory devices, attributable to the different morphologies of the hybrid dielectric layers and the different sizes of the distributed perovskite nanoparticles (NPs). The photo-response behavior and the resultant On/Off current ratio increased as the size of the embedded perovskite NPs decreased, due to the enhanced photo-induced charge transfer across the dielectric/pentacene interface, benefiting from the better confinement effect of perovskite NPs in the polymer matrix. These results demonstrate the influence of perovskite NP aggregation at the dielectric/pentacene interface on the resultant memory behavior of the newly developed photo-memory device.

Ultra-Bright Near-Infrared Perovskite Light-Emitting Diodes with Reduced Efficiency Roll-off

Herein, an insulating biopolymer is exploited to guide the controlled formation of micro/nano-structure and physical confinement of α-δ mixed phase crystalline grains of formamidinium lead iodide (FAPbI₃) perovskite, functioning as charge carrier concentrators and ensuring improved radiative recombination and photoluminescence quantum yield (PLQY). This composite material is used to build highly efficient near-infrared (NIR) FAPbI₃ Perovskite light-emitting diodes (PeLEDs) that exhibit a high radiance of 206.7 W/sr*m², among the highest reported for NIR-PeLEDs, obtained at a very high current density of 1000 mA/cm², while importantly avoiding the efficiency roll-off effect. In depth photophysical characterization allows to identify the possible role of the biopolymer in i) enhancing the radiative recombination coefficient, improving light extraction by reducing the refractive index, or ii) enhancing the effective optical absorption because of dielectric scattering at the polymer-perovskite interfaces. Our study reveals how the use of insulating matrixes for the growth of perovskites represents a step towards high power applications of PeLEDs.

Connecting the solution chemistry of PbI2 and MAI: a cyclodextrin-based supramolecular approach to the formation of hybrid halide perovskites

Cyclodextrin macrocycles are able to modify and control the solvation equilibria of hybrid perovskite components in solution by establishing supramolecular interactions.

The evolution from solvated precursors to hybrid halide perovskite films dictates most of the photophysical and optoelectronic properties of the final polycrystalline material. Specifically, the complex equilibria and the importantly different solubilities of lead iodide (PbI₂) and methylammonium iodide (MAI) induce inhomogeneous crystal growth, often leading to a defect dense film showing non-optimal optoelectronic properties and intrinsic instability. Here, we explore a supramolecular approach based on the use of cyclodextrins (CDs) to modify the underlying solution chemistry. The peculiar phenomenon demonstrated is a tunable complexation between different CDs and MA⁺ cations concurrent to an out of cage PbI₂ intercalation, representing the first report of a connection between the solvation equilibria of the two perovskite precursors. The optimal conditions in terms of CD cavity size and polarity translate to a neat enhancement of PbI₂ solubility in the reaction media, leading to an equilibration of the availability of the precursors in solution. The macroscopic result of this is an improved nucleation process, leading to a perovskite material with higher crystallinity, better optical properties and improved moisture resistance. Remarkably, the use of CDs presents a great potential for a wide range of device-related applications, as well as for the development of tailored composite materials.

Highly Stable and Luminescent Perovskite-Polymer Composites from a Convenient and Universal Strategy

Extensive attention has been received in recent years for perovskite-polymer composites because of their combination of properties from polymers and perovskites. In this work, a convenient and universal strategy is reported to prepare cesium lead bromide or organolead halide methylammonium bromide polymer composites. This technique integrates the formation of perovskite crystals and the polymer matrix in a one-pot reaction, avoiding the tedious separation and preparation of perovskites. The method is universal for most of the commercially available monomers and polymers, which has been verified in this report using poly(methyl methacrylate), poly(butyl methacrylate), and polystyrene. The physical properties of the varied polymers lead to different luminescent properties and stabilities of the composites. No organic solvent is required during the preparation, indicating a green technique for the composites. Additionally, the resulted perovskite-polymer composites are extraordinarily stable, maintaining their quantum yield for more than 1 month in air. On the basis of the above properties, a prototype of white light-emitting diodes was successfully constructed with feasible color characters and narrow bandwidths. Furthermore, large-area (dimension: 10 × 7 × 0.15 cm) perovskite-polymer plates are easily prepared via the one-pot strategy, showing that the technique is ready for possible large-area optical devices. This work provides an efficient technique toward various kinds of perovskite-polymer composites for both scientific research studies and future applications.

GO/PEDOT:PSS nanocomposites: effect of different dispersing agents on rheological, thermal, wettability and electrochemical properties

In this work glucose (G), α-cyclodextrin (α-CD) and sodium salt of carboxymethyl cellulose (CMCNa) are used as dispersing agents for graphene oxide (GO), exploring the influence of both saccharide units and geometric/steric hindrance on the rheological, thermal, wettability and electrochemical properties of a GO/poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) nanocomposite. By acting on the saccharide-based additives, we can modulate the rheological, thermal, and wettability properties of the GO/PEDOT:PSS nanocomposite. Firstly, the influence of all the additives on the rheological behaviour of GO and PEDOT:PSS was investigated separately in order to understand the effect of the dispersing agent on both the components of the ternary nanocomposite, individually. Subsequently, steady shear and dynamic frequency tests were conducted on all the nanocomposite solutions, characterized by thermal, wettability and morphological analysis. Finally, the electrochemical properties of the GO/PEDOT composites with different dispersing agents for supercapacitors were investigated using cyclic voltammetry (CV). The CV results revealed that GO/PEDOT with glucose exhibited the highest specific capacitance among the systems investigated.

Elucidating the effect of the lead iodide complexation degree behind the morphology and performance of perovskite solar cells

The inclusion of iodide additives in hybrid perovskite precursor solutions has been successfully exploited to improve the solar cell efficiency but their impact on perovskite formation, morphology and photovoltaic performance is still not clear. Here an extensive analysis of the effect of iodide additives in the solution-phase and during the perovskite film formation, as well as their effect on device performance is provided. The results demonstrate that in the solution-phase the additives promote the formation of lead poly-iodide species resulting in the disaggregation of the inorganic lead iodide framework and in the formation of smaller nuclei inducing the growth of uniform and smooth perovskite films. Most importantly, the complexation capability of different iodide additives does not only directly affect film morphology but also influences the density of defect states by varying the stoichiometry of precursors. These findings demonstrate that the fine control of the interactions of the chemical species in the solution-phase is essential for the precise control of the morphology at the nanoscale and the growth of the perovskite films with a reduced density of defect states. Therefore, the in-depth understanding of all the processes involved in the solution-phase is the first step for the development of a facile and reproducible approach for the fabrication of hybrid perovskite solar cells with enhanced photovoltaic performance.

Large grain growth for hole-conductor-free fully printable perovskite solar cells via polyoxometalate molecular doping

Polyoxometalate-induced Ostwald ripening process occurring during the crystal grain growth of perovskite film, achieving a grain size of 30 μm.

Exploration of organic–inorganic hybrid perovskites for surface-enhanced infrared spectroscopy of small molecules

Organic–inorganic hybrid perovskites allow the infrared absorption of small molecules to be efficiently enhanced.

The Bright Side of Perovskites

Incubating in the rise of perovskite photovoltaic era, the advances in material design encourage further promising optoelectronic exploitations. Here, we evaluate halide perovskite envisioning light-emitting applications, with a particular focus to the role that this material can effectively play in the field, discussing advantages and limitations with respect to state of art competing players. Specific benefits derive from the use of low dimensional and nanostructured perovskites, marginally exploited in photovoltaic devices, allowing for a tuning of the excited states properties and for the obtainment of intrinsic resonating structures. Thanks to these unique properties, halide perovskite ensure a great potential for the development of high-power applications, such as lighting and lasing.

Covalently Functionalized SWCNTs as Tailored p-Type Dopants for Perovskite Solar Cells

The covalent functionalization of (7,6)-enriched single-walled carbon nanotubes (SWCNTs) with oligophenylenevinylene (OPV) moieties terminating with a dimethylamino group is proposed as an efficient way to enhance the affinity of CNTs with spiro-MeOTAD in perovskite-based solar cells. The evidence of SWCNTs functionalization and the degree of OPV substitution on SWCNTs are established from TGA, XPS, TEM, and Raman techniques. Our tailored doping materials afford photovoltaic performances in line with conventional Li-doped spiro-MeOTAD, showing at the same time a significantly improved chemical stability of the perovskite component over time. Furthermore, the comparison of the photovoltaic performances with those obtained with nonfunctionalized SWCNTs suggest that the presence of the organic appends ensures highly reproducible PV performances. These results demonstrate the suitability of this functionalized SWCNT material as a valid doping agent for spiro-MeOTAD, representing a viable alternative to the conventional Li salt.

A highly photoconductive composite prepared by incorporating polyoxometalate into perovskite for photodetection application

A photoconductive perovskite-polyoxometalate composite was prepared for the first time by a facile low-temperature and solution-processed method, and this composite exhibited a significantly enhanced photoconductivity and photodetection performance due to introduction of polyoxometalate into the perovskite for fine energy-level matching and efficient charge transfer.