Carbon-Coated SiO2 Composites as Promising Anode Material for Li-Ion Batteries

Porous silica-based materials are a promising alternative to graphite anodes for Li-ion batteries due to their high theoretical capacity, low discharge potential similar to pure silicon, superior cycling stability compared to silicon, abundance, and environmental friendliness. However, several challenges prevent the practical application of silica anodes, such as low coulombic efficiency and irreversible capacity losses during cycling. The main strategy to tackle the challenges of silica as an anode material has been developed to prepare carbon-coated SiO₂ composites by carbonization in argon atmosphere. A facile and eco-friendly method of preparing carbon-coated SiO₂ composites using sucrose is reported herein. The carbon-coated SiO₂ composites were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, thermogravimetry, transmission and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy, cyclic voltammetry, and charge–discharge cycling. A C/SiO₂-0.085 M calendered electrode displays the best cycling stability, capacity of 714.3 mAh·g⁻¹, and coulombic efficiency as well as the lowest charge transfer resistance over 200 cycles without electrode degradation. The electrochemical performance improvement could be attributed to the positive effect of the carbon thin layer that can effectively diminish interfacial impedance.

Spray-Printed and Self-Assembled Honeycomb Electrodes of Silicon-Decorated Carbon Nanofibers for Li-Ion Batteries

Directional, micron-scale honeycomb pores in Li-ion battery electrodes were fabricated using a layer-by-layer, self-assembly approach based on spray-printing of carbon nanofibers. By controlling the drying behavior of each printed electrode layer through optimization of (i) the volume ratio of fugitive bisolvent carriers in the suspension and (ii) the substrate temperature during printing, self-assembled, honeycomb pore channels through the electrode were created spontaneously and reliably on current collector areas larger than 20 cm × 15 cm. The honeycomb pore structure promoted efficient Li-ion dynamics at high charge/discharge current densities. Incorporating an optimum fraction (2.5 wt %) of high-energy-density Si particulate into the honeycomb electrodes provided a 4-fold increase in deliverable discharge capacity at 8000 mA/g. The spray-printed, honeycomb pore electrodes were then investigated as negative electrodes coupled with similar spray-printed LiFePO₄ positive electrodes in a full Li-ion cell configuration, providing an approximately 50% improvement in rate capacity retention over half-cell configurations of identical electrodes at 4000 mA/g.

High performance lithium battery anode materials by coating SiO2 nanowire arrays with PEO

SiO₂@PEO nanowire arrays were prepared by a simple method and exhibited excellent electrochemical performance as LIB anode materials.

Surface Decoration of Pt Nanoparticles via ALD with TiO2 Protective Layer on Polymeric Nanofibers as Flexible and Reusable Heterogeneous Nanocatalysts

Coupling the functional nanoheterostructures over the flexible polymeric nanofibrous membranes through electrospinning followed by the atomic layer deposition (ALD), here we presented a high surface area platform as flexible and reusable heterogeneous nanocatalysts. Here, we show the ALD of titanium dioxide (TiO₂) protective nanolayer onto the electrospun polyacrylonitrile (PAN) nanofibrous web and then platinum nanoparticles (Pt-NP) decoration was performed by ALD onto TiO₂ coated PAN nanofibers. The free-standing and flexible Pt-NP/TiO₂-PAN nanofibrous web showed the enhancive reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) within 45 seconds though the hydrogenation process with the degradation rate of 0.1102 s⁻¹. The TiO₂ protective layer on the PAN polymeric nanofibers was presented as an effective route to enhance the attachment of Pt-NP and to improve the structure stability of polymeric nanofibrous substrate. Commendable enhancement in the catalytic activity with the catalytic dosage and the durability after the reusing cycles were investigated over the reduction of 4-NP. Even after multiple usage, the Pt-NP/TiO₂-PAN nanofibrous webs were stable with the flexible nature with the presence of Pt and TiO₂ on its surface.

Flower-like carbon with embedded silicon nano particles as an anode material for Li-ion batteries

A novel 3-dimensional (3D) flower-like silicon/carbon composite was synthesized through spray drying method by using NaCl as the sacrificial reagent and was evaluated as an anode material for lithium ion batteries.