Antimony reduction by a non-conventional sulfate reducer with simultaneous bioenergy production in microbial fuel cells

Environmental toxicity of antimony (Sb) is significantly increased through the widespread industrial application. The extended release of Sb above the regulatory level became a risk to humans habituated in the ecosystem. Conventional methods to remediate Sb demand high energy or resource input, which further leads to secondary pollution. The bio-electrochemical system offers a promising bioremediation strategy to remove or reduce toxic heavy metals. Thus, this research explores the possibilities of simultaneous metal sulfide (MeS) precipitation and electricity production using a full biological Microbial fuel cell (MFC). A non-conventional sulfate-reducing bacteria (SRB) Citrobacter freundii SR10 was used for this investigation, where the MFC was operated for lactate utilization in the bio-anode and Sb reduction at the bio-cathode. This study observed 81% of coulombic efficiency (bio-anode) and 97% of sulfate reduction with 99.3% Sb (V) reduction (bio-cathode), and it was concluded that the MeS precipitation entirely depends on sulfide concentration via SR10 sulfate reduction. The MFC-SR10 offers a maximum power density of 1652.9 ± 32.1 mW/m^3, and their performance was depicted using cyclic voltammetry and electrochemical impedance spectroscopy. The Sb reduction was evaluated through fluorescence spectroscopy, and the Sb (V) MeS precipitation was confirmed as stibnite (Sb₂S₃) by Raman spectroscopy and X-ray photoelectron spectroscopy. Furthermore, the matured anodic and cathodic biofilm formation was confirmed by Scanning electron microscopy with Energy-dispersive X-ray spectroscopy. Thus the MFC with SRB bio-cathode can be used as an alternative to simultaneously remove sulfate and Sb from the wastewater with electricity production.

Electrified bioreactors: the next power-up for biometallurgical wastewater treatment

Over the past decades, biological treatment of metallurgical wastewaters has become commonplace. Passive systems require intensive land use due to their slow treatment rates, do not recover embedded resources and are poorly controllable. Active systems however require the addition of chemicals, increasing operational costs and possibly negatively affecting safety and the environment. Electrification of biological systems can reduce the use of chemicals, operational costs, surface footprint and environmental impact when compared to passive and active technologies whilst increasing the recovery of resources and the extraction of products. Electrification of low rate applications has resulted in the development of bioelectrochemical systems (BES), but electrification of high rate systems has been lagging behind due to the limited mass transfer, electron transfer and biomass density in BES. We postulate that for high rate applications, the electrification of bioreactors, for example, through the use of electrolyzers, may herald a new generation of electrified biological systems (EBS). In this review, we evaluate the latest trends in the field of biometallurgical and microbial‐electrochemical wastewater treatment and discuss the advantages and challenges of these existing treatment technologies. We advocate for future research to focus on the development of electrified bioreactors, exploring the boundaries and limitations of these systems, and their validity upon treating industrial wastewaters.

Microbial sulfite oxidation coupled to nitrate reduction in makeup water for oil production

Bisulfite is used as an oxygen scavenger in waters used for oil production to prevent oxygen-mediated pipeline corrosion. Analysis of nitrate-containing water injected with ammonium bisulfite indicated increased concentrations of ammonium, sulfate and nitrite. To understand the microbial process causing these changes, water samples were used in enrichments with bisulfite and nitrate. Oxidation of bisulfite, reduction of nitrate, change in microbial community composition and corrosivity of bisulfite were determined. The results indicated that the microbial community was dominated by Sulfuricurvum, a sulfite-oxidizing nitrate-reducing bacterium (StONRB). Plating of the enriched StONRB culture yielded the bacterial isolate Sulfuricurvum sp. TK005, which coupled bisulfite oxidation with nitrate reduction to form sulfate and nitrite. Bisulfite also induced chemical corrosion of carbon steel at a rate of 0.28 ± 0.18 mm yr^-1. Bisulfite and the generated sulfate could serve as electron acceptors for sulfate-reducing microorganisms (SRM), which reduce sulfate and bisulfite to sulfide. Nitrate is frequently injected to injection waters to contain the activity of SRM in oil reservoirs. This study suggests an alternative bisulfite injection procedure: Injection of nitrate after the chemical reaction of bisulfite with oxygen is completed. This could maintain the oxygen scavenger function of bisulfite and SRM inhibitory activity of nitrate.

Efficient reduction of antimony by sulfate-reducer enriched bio-cathode with hydrogen production in a microbial electrolysis cell

Bio-cathode Microbial electrolysis cell (MEC) is a promising and eco-friendly technology for concurrent hydrogen production and heavy metal reduction. However, the bioreduction of Antimony (Sb) in a bio-electrochemical system with H₂ production is not explored. In this study, two efficient sulfate-reducing bacterial (SRB) strains were used to investigate the enhanced bioreduction of sulfate and Sb with H₂ production in the MEC. SRB Bio-cathode MEC was developed from the microbial fuel cell (MFC) and operated with an applied voltage of 0.8 V. The performance of the SRB bio-cathode was confirmed by cyclic voltammetry, linear sweep voltammetry and electrochemical impedance spectroscopy. SRB strains of BY7 and SR10 supported the synergy reduction of sulfate and Sb by sulfide metal precipitation reaction. Hydrogen gas was the main product of SRB bio-cathode, with 86.9%, and 83.6% of H₂ is produced by SR10 and BY7, respectively. Sb removal efficiency reached up to 88.2% in BY7 and 96.3% in SR10 with a sulfate reduction rate of 92.3 ± 2.6 and 98.4 ± 1.6 gm^-3d^-1 in BY7 and SR10, respectively. The conversion efficiency of Sb (V) to Sb (III) reached up to 70.1% in BY7 and 89.2% in SR10. It was concluded that the total removal efficiency of Sb relies on the amount of sulfide concentration produced by the sulfate reduction reaction. The hydrogen production rate was increased up to 1.25 ± 0.06 (BY7) and 1.36 ± 0.02 m³ H₂/(m³·d) (SR10) before addition of Sb and produced up to 0.893 ± 0.03 and 0.981 ± 0.02 m³H₂/(m³·d) after addition of Sb. The precipitates were characterized by X-ray diffraction and X-ray photoelectron spectroscopy, which confirmed Sb (V) was reduced to Sb₂S₃.

Generation of electrical energy in a microbial fuel cell coupling acetate oxidation to Fe3+ reduction and isolation of the involved bacteria

An iron reducing enrichment was obtained from sulfate reducing sludge and was evaluated on the capability of reducing Fe³⁺ coupled to acetate oxidation in a microbial fuel cell (MFC). Three molar ratios for acetate/Fe³⁺ were evaluated (2/16, 3.4/27 and 6.9/55 mM). The percentages of Fe³⁺ reduction were in a range of 80-90, 60-70 and 40-50% for the MFCs at closed circuit for the molar ratios of 2/16, 3.4/27 and 6.9/55 mM, respectively. Acetate consumption was in a range of 80-90% in all cases. The results obtained at closed circuit for current density were: 11.37 mA/m², 4.5 mA/m² and 7.37 mA/m² for the molar ratios of 2/16, 3.4/27 and 6.9/55 mM, respectively. Some microorganisms that were isolated and identified in the MFCs were Azospira oryzae, Cupriavidus metallidurans CH34, Enterobacter bugandensis 247BMC, Citrobacter freundii ATCC8090 and Citrobacter murliniae CDC2970-59, these bacteria have been reported as exoelectrogens in MFC and in MFC involving metals removal but not all of them have been reported to utilize acetate as preferred substrate. The results demonstrate that the isolates can utilize acetate as the sole source of carbon and suggest that Fe³⁺ reduction was carried out by a combination of different mechanisms (direct contact and redox mediators) utilized by the bacteria identified in the MFC. Storage of the energy generated from the 2/16 mM MFC system arranged in a series of three demonstrated that it is possible to utilize the energy to charge a battery.

Bioelectrochemical remediation of phenanthrene in a microbial fuel cell using an anaerobic consortium enriched from a hydrocarbon-contaminated site

Polycyclic aromatic hydrocarbons (PAH) are organic pollutants that require remediation due to their detrimental impact on human and environmental health. In this study, we used a novel approach of sequestering a model PAH, phenanthrene, onto a solid carbon matrix bioanode in a microbial fuel cell (MFC) to assess its biodegradation coupled with power generation. Here, the bioanode serves as a site for enrichment of electroactive and hydrocarbon-degrading microorganisms, which can simultaneously act to biodegrade a pollutant and generate power. Carbon cloth electrodes loaded with two rates of phenanthrene (2 and 20 mg cm^-2) were compared using dual chamber MFCs that were operated for 50 days. The lower loading rate of 2 mg cm^-2 was most efficient in the degradation of phenanthrene and had higher power production capacities (37 mW m^-2) as compared to the higher loading rate of 20 mg cm^-2 (power production of 19.2 mW m^-2). FTIR (Fourier-Transform Infrared Spectroscopy) analyses showed a depletion in absorbance peak signals associated with phenanthrene. Microbes known to have electroactive properties or phenanthrene biodegradation abilities like Pseudomonas, Rhodococcus, Thauera and Ralstonia were enriched over time in the MFCs, substantiating the electrochemical and FTIR analyses. The MFC approach taken here thus offers great promise towards PAH bioelectroremediation.

Biosensing capabilities of bioelectrochemical systems towards sustainable water streams: Technological implications and future prospects

Bioelectrochemical systems (BESs) have been intensively investigated over the last decade owing to its wide-scale environmentally friendly applications, among which wastewater treatment, power generation and environmental monitoring for pollutants are prominent. Different variants of BES such as microbial fuel cell, microbial electrolysis cell, microbial desalination cell, enzymatic fuel cell, microbial solar cell, have been studied. These microbial bioelectrocatalytic systems have clear advantages over the existing analytical techniques for sustainable on-site application in wide environmental conditions with minimum human intervention, making the technology irrevocable and economically feasible. The key challenges to establish this technology are to achieve stable and efficient interaction between the electrode surface and microorganisms, reduction of time for start-up and toxic-shock recovery, sensitivity improvement in real-time conditions, device miniaturization and its long-term economically feasible commercial application. This review article summarizes the recent technical progress regarding bio-electrocatalytic processes and the implementation of BESs as a biosensor for determining various compositional characteristics of water and wastewater.

Comparative Evaluation of Coated and Non-Coated Carbon Electrodes in a Microbial Fuel Cell for Treatment of Municipal Sludge

This study aims to provide insight into the cost-effective catalyst on power generation in a microbial fuel cell (MFC) for treatment of municipal sludge. Power production from MFCs with carbon, Fe2O3, and Pt electrodes were compared. The MFC with no coating on carbon generated the least power density (6.72 mW·m−2) while the MFC with Fe2O3-coating on carbon anodes and carbon cathodes generated a 78% higher power output (30.18 mW·m−2). The third MFC with Fe2O3-coated carbon anodes and Pt on carbon as the cathode catalyst generated the highest power density (73.16 mW·m−2) at room temperature. Although the power generated with a conventional Pt catalyst was more than two-fold higher than Fe2O3, this study suggests that Fe2O3 can be investigated further as an efficient, low-cost, and alternative catalyst of Pt, which can be optimized for improving performance of MFCs. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) results demonstrated reduced resistance of MFCs and better charge transfer between biofilm and electrodes containing coated anodes compared to non-coated anodes. Scanning electron microscopy (SEM) was used to analyze biofilm morphology and microbial community analysis was performed using 16S rRNA gene sequencing, which revealed the presence of known anaerobic fermenters and methanogens that may play a key role in energy generation in the MFCs.

Effect of selected biocides on microbiologically influenced corrosion caused by Desulfovibrio ferrophilus IS5

The marine bacterial strain Desulfovibrio ferrophilus IS5, known for its lithotrophic growth ability to use metallic iron as a sole electron donor and for causing corrosion of steel, was used in the current study. Four commonly used biocides in the oil and gas industry, namely tetrakis(hydroxymethyl) phosphonium sulfate (THPS), glutaraldehyde (GLUT), benzalkonium chloride (BAC), and GLUT/BAC were selected to study their efficacy in controlling carbon steel corrosion in the presence of this strain. Incubations containing strain IS5 and low carbon steel coupons were prepared in the presence and absence of the four biocides, and these were monitored using both electrochemical methods (electrochemical impedance spectroscopy, linear polarization resistance and potentiodynamic polarization) and surface analyses (scanning electron microscopy, confocal measurements, optical microscopy, and profilometry) to assess the biofilm/metal interactions. When THPS, BAC, and GLUT/BAC treatments were applied, minimal corrosion was measured by all methods. In contrast, severe pitting was observed in the presence of 50 ppm GLUT, similar to what was observed when D. ferrophilus IS5 was incubated in the absence of biocide, suggesting that GLUT alone may not be effective in controlling MIC in marine environments. This study also showed that the use of non-destructive electrochemical methods is effective for screening for real time biocide selection and monitoring of the impact of chemicals post-dosage in oil and gas operations.

Simultaneous nitrification and denitrification using a polypyrrole/microbial cellulose electrode in a membraneless bio-electrochemical system

In this study, the feasibility of ammonium and total nitrogen removal from aqueous solution using a simultaneous nitrification and denitrification process was studied in a membraneless bio-electrochemical system with a novel electrode.