Structural studies of calcium silicate hydrate modified with heavy metal cations

This study investigates the immobilization mechanisms of heavy metal ions in the C-S-H phase. Synthetic C-S-H phases were prepared via the precipitation method, incorporating five different ions (Pb(II), Cd(II), Ni(II), Zn(II), and Cr(III)). Structural analysis of the obtained material was conducted using vibrational spectroscopy (both FT-IR and Raman), X-ray photoelectron spectroscopy, and X-ray diffraction. Spectroscopic methods were primarily employed to evaluate the structural effects and polymerization degree of the resulting C-S-H phase. Morphological changes were characterized using scanning and transmission electron microscopy (SEM and TEM, respectively). Our findings reveal several mechanisms for immobilizing heavy metal cations: precipitation of insoluble compounds (particularly notable for Ni(II) and Cr(III)), replacement of Ca(II) ions within the silicate structure (evident in the crystallization of Ca(OH)2 in samples containing Cd(II), Ni(II), and Zn(II) in minimal quantities), and strong bonding of certain metals (such as Pb(II)) with the C-S-H phase structure. These insights contribute to understanding the potential applications of C-S-H phases in heavy metal immobilization.

Effect of Carbon Layer Thickness on the Electrocatalytic Oxidation of Glucose in a Ni/BDD Composite Electrode

High-performance non-enzymatic glucose sensor composite electrodes were prepared by loading Ni onto a boron-doped diamond (BDD) film surface through a thermal catalytic etching method. A carbon precipitate with a desired thickness could be formed on the Ni/BDD composite electrode surface by tuning the processing conditions. A systematic study regarding the influence of the precipitated carbon layer thickness on the electrocatalytic oxidation of glucose was conducted. While an oxygen plasma was used to etch the precipitated carbon, Ni/BDD-based composite electrodes with the precipitated carbon layers of different thicknesses could be obtained by controlling the oxygen plasma power. These Ni/BDD electrodes were characterized by SEM microscopies, Raman and XPS spectroscopies, and electrochemical tests. The results showed that the carbon layer thickness exerted a significant impact on the resulting electrocatalytic performance. The electrode etched under 200 W power exhibited the best performance, followed by the untreated electrode and the electrode etched under 400 W power with the worst performance. Specifically, the electrode etched under 200 W was demonstrated to possess the highest sensitivity of 1443.75 μA cm-2 mM-1 and the lowest detection limit of 0.5 μM.

Developments of the Electroactive Materials for Non-Enzymatic Glucose Sensing and Their Mechanisms

A comprehensive review of the electroactive materials for non-enzymatic glucose sensing and sensing devices has been performed in this work. A general introduction for glucose sensing, a facile electrochemical technique for glucose detection, and explanations of fundamental mechanisms for the electro-oxidation of glucose via the electrochemical technique are conducted. The glucose sensing materials are classified into five major systems: (1) mono-metallic materials, (2) bi-metallic materials, (3) metallic-oxide compounds, (4) metallic-hydroxide materials, and (5) metal-metal derivatives. The performances of various systems within this decade have been compared and explained in terms of sensitivity, linear regime, the limit of detection (LOD), and detection potentials. Some promising materials and practicable methodologies for the further developments of glucose sensors have been proposed. Firstly, the atomic deposition of alloys is expected to enhance the selectivity, which is considered to be lacking in non-enzymatic glucose sensing. Secondly, by using the modification of the hydrophilicity of the metallic-oxides, a promoted current response from the electro-oxidation of glucose is expected. Lastly, by taking the advantage of the redistribution phenomenon of the oxide particles, the usage of the noble metals is foreseen to be reduced.

Nanostructured nickel oxide electrodes for non-enzymatic electrochemical glucose sensing

Nanostructured nickel (Ni) and nickel oxide (NiO) electrodes were fabricated on Ni foils using the glancing angle deposition (GLAD) technique. Cyclic voltammetry and amperometry showed the electrodes enable non-enzymatic electrochemical determination of glucose in strongly alkaline media. Under optimized conditions of NaOH concentration and working potential (~ 0.50 V vs. Ag/AgCl), the GLAD electrodes performed far better than bare Ni foil electrodes, with the GLAD NiO electrode showing an outstanding sensitivity (4400 μA mM^-1 cm^-2), superior detection limit (7 nM), and wide dynamic range (0.5 μM-9 mM), with desirable selectivity and reproducibility. Based on their performance at a low concentration, the GLAD NiO electrodes were also used to quantify glucose in artificial urine and sweat samples which have significantly lower glucose levels than blood. The GLAD NiO electrodes showed negligible response to the common interferents in glucose measurement (uric acid, dopamine, serotonin, and ascorbic acid), and they were not poisoned by high amounts of sodium chloride. Graphical abstract The figures depict (A) SEM image of vertical post-GLAD NiO electrodes used for non-enzymatic electrochemical glucose monitoring, and (B) calibration plots of the three different electrodes.

Modern Approach to the Synthesis of Ni(OH)2 Decorated Sulfur Doped Carbon Nanoparticles for the Nonenzymatic Glucose Sensor

As a growing aspect of materials science, there are an enormous number of synthesis routes that have been identified to produce materials, particularly through simple methodologies. In this way, the present study focuses on the easiest way to prepare sulfur doped carbon nanoparticles (SDCNs) using a flame synthesis method and has also demonstrated a novel route to synthesize Ni(OH)2 decorated SDCNs by a simple adsorption cum precipitation method. The SDCNs are alternative candidates to prestigious carbon materials such as graphene, carbon nanotubes, and fullerenes. Moreover, SDCNs provide excellent support to the Ni(2+) ion adsorption and initiate the formation of Ni(OH)2. The formation of Ni(OH)2 on the SDCN matrix was confirmed by Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray diffraction (XRD), selected area diffraction pattern (SAED), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). After these meticulous structural evaluations, we have described the mechanism for the formation of Ni(OH)2 on an SDCN matrix. The as-prepared Ni(OH)2 decorated SDCN nanocomposites were used as an electrode material for nonenzymatic glucose sensors. The fabricated glucose sensor exhibited a wide linear concentration range, 0.0001-5.22 mM and 5.22-10.22 mM, and a low-level detection limit of 28 nM. Additionally, it reveals excellent selectivity in the potentially interfering ions and also possesses a good stability. The practicality of the fabricated glucose sensor was also demonstrated toward glucose detection in biological samples.