Locally Self-Adjustive Smoothing for Measurement Noise Reduction with Application to Automated Peak Detection

Smoothing is a widely used approach for measurement noise reduction in spectral analysis. However, it suffers from signal distortion caused by peak suppression. A locally self-adjustive smoothing method is developed that retains sharp peaks and less distorted signals. The proposed method uses only one parameter that determines the global smoothness of data, while balancing the local smoothness using the data itself. Simulation and real experiments in comparison with existing convolution-based smoothing methods indicate both qualitatively and quantitatively improved noise reduction performance in practical scenarios. We also discuss parameter selection and demonstrate an application for the automated smoothing and detection of a given number of peaks from noisy measurement data.

DES-ultrasonication treatment of cellulose nanocrystals and the reinforcement in carrageenan biocomposite

CNCs are intensively studied to reinforce biocomposites. However, it remains a challenge to homogeneously disperse the CNC in biocomposites for a smooth film surface. Mechanochemical treatment via ultrasonication in deep eutectic solvent (DES) generated a stable dispersion of CNC before incorporation into carrageenan biocomposite. Shifted peaks of choline chloride (ChCl) methylene groups to 3.95-3.98 ppm in 1H NMR indicated a formation of eutectic mixture between the hydrogen bond acceptor (HBA) and hydrogen bond donor (HBD) at the functional group of CH3···OH. The swelling of CNC in the DES was proven by the formation of intermolecular H-bond at a length of 2.46 Å. The use of DES contributed to a good dispersion of CNC in the solution which increased zeta potential by 43.2 % compared to CNC in deionized water. The ultrasonication amplitude and feed concentration were varied for the best parameters of a stable dispersion of CNC. The crystallinity of 1 wt% of CNC at 20 % sonication amplitude improved from 76 to 81 %. The high crystallinity of CNCDES resulted in an increase in film tensile and capsule loop strength of Carra-CNCDES by 20.7 and 19.4 %, respectively. Improved dispersion of CNCDES reduced the surface roughness of the biocomposite by 21.8 %. H-bond network in CNCDES improved the biocomposite properties for an ingenious reinforcement material.

Nanocellulose: A comprehensive review investigating its potential as an innovative material for water remediation

Rapid growth in industrialization sectors, the wastewater treatment plants become exhausted and potentially not able to give desirable discharge standards. Many industries discharge the untreated effluent into the water bodies which affects the aquatic diversity and human health. The effective disposal of industrial effluents thus has been an imperative requirement. For decades nanocellulose based materials gained immense attraction towards application in wastewater remediation and emerged out as a new biobased nanomaterial. It is light weighted, cost effective, mechanically strong and easily available. Large surface area, versatile surface functionality, biodegradability, high aspect ratio etc., make them suitable candidate in this field. Majorly cellulose based nanomaterials are used in the form of cellulose nanocrystals (CNCs), cellulose nanofibers (CNFs), or bacterial nanocellulose (BNC). This review specifically describes about a variety of extraction methods to produced nanocellulose and also discusses the modification of nanocellulose by adding functionalities in its surface chemistry. We majorly focus on the utilization of nanocellulose based materials in water remediation for the removal of different contaminants such as dyes, heavy metals, oil, microbial colony etc. This review mainly emphasizes in ray of hope towards nanocellulose materials to achieve more advancement in the water remediation fields.

Controlling the critical parameters of ultrasonication to affect the dispersion state, isolation, and chiral nematic assembly of cellulose nanocrystals

Cellulose nanocrystals (CNCs) are typically extracted from plants and present a range of opto-mechanical properties that warrant their use for the fabrication of sustainable materials. While their commercialization is ongoing, their sustainable extraction at large scale is still being optimized. Ultrasonication is a well-established and routinely used technology for (re-) dispersing and/or isolating plant-based CNCs without the need for additional reagents or chemical processes. Several critical ultrasonication parameters, such as time, amplitude, and energy input, play dominant roles in reducing the particle size and altering the morphology of CNCs. Interestingly, this technology can be coupled with other methods to generate moderate and high yields of CNCs. Besides, the ultrasonics treatment also has a significant impact on the dispersion state and the surface chemistry of CNCs. Accordingly, their ability to self-assemble into liquid crystals and subsequent superstructures can, for example, imbue materials with finely tuned structural colors. This article gives an overview of the primary functions arising from the ultrasonication parameters for stabilizing CNCs, producing CNCs in combination with other promising methods, and highlighting examples where the design of photonic materials using nanocrystal-based celluloses is substantially impacted.

Recent advances in qualitative and quantitative characterization of nanocellulose-reinforced nanocomposites: A review

Nanocellulose has received immense consideration owing to its valuable inherent traits and impressive physicochemical properties such as biocompatibility, thermal stability, non-toxicity, and tunable surface chemistry. These features have inspired researchers to deploy nanocellulose as nanoscale reinforcement materials for bio-based polymers. A simple yet efficient characterization method is often required to gain insights into the effectiveness of various types of nanocellulose. Despite a decade of continuous research and booming growth in scientific publications, nanocellulose research lacks a measuring tool that can characterize its features with acceptable speed and reliability. Implementing reliable characterization techniques is critical to monitor the specifications of nanocellulose alone or in the final product. Many techniques have been developed aiming to measure the nano-reinforcement mechanisms of nanocellulose in polymer composites. This review gives a full account of the scientific underpinnings of techniques that can characterize the shape and arrangement of nanocellulose. This review aims to deliver consolidated details on the properties and characteristics of nanocellulose in biopolymer composite materials to improve various structural, mechanical, barrier and thermal properties. We also present a comprehensive description of the safety features of nanocellulose before and after being loaded within biopolymeric matrices.

Cellulose Nanocrystal (CNC) Gels: A Review

The aim of this article is to review the research conducted in the field of aqueous and polymer composites cellulose nanocrystal (CNC) gels. The experimental techniques employed to characterize the rheological behavior of these materials will be summarized, and the main advantages of using CNC gels will also be addressed in this review. In addition, research devoted to the use of numerical simulation methodologies to describe the production of CNC-based materials, e.g., in 3D printing, is also discussed. Finally, this paper also discusses the application of CNC gels along with additives such as cross-linking agents, which can represent an enormous opportunity to develop improved materials for manufacturing processes.

Morphological, Spectroscopic and Thermal Analysis of Cellulose Nanocrystals Extracted from Waste Jute Fiber by Acid Hydrolysis

Natural cellulose, a sustainable bioresource, is highly abundant in nature. Cellulosic materials, particularly those that explore and employ such materials for industrial use, have recently attracted significant global attention in the field of material science because of the unique properties of cellulose. The hydroxyl groups enable the formation of intra- and inter-molecular hydrogen bonding and the arrangement of cellulose chains in a highly ordered crystalline zone, with the remaining disordered structure referred to as an amorphous region. The crystalline areas of cellulose are well-known as cellulose nanocrystals (CNCs). In the present study, we extracted CNCs from pure cellulose isolated from waste jute fibers by sulfuric acid hydrolysis, followed by characterization. Pure cellulose was isolated from jute fibers by treating with sodium hydroxide (20% w/w) and anthraquinone (0.5%) solution at 170 °C for 2 h, followed by bleaching with chlorine dioxide and hydrogen peroxide solution. CNCs were isolated from pure cellulose by treating with different concentrations (58% to 62%) of sulfuric acid at different time intervals (20 min to 45 min). The FTIR study of the CNCs reveals no peak at 1738 cm^-1, which confirms the absence of hemicellulose in the samples. The CNCs obtained after 45 min of acid hydrolysis are rod-shaped, having an average length of 800 ± 100 nm and width of 55 ± 10 nm, with a high crystallinity index (90%). Zeta potential significantly increased due to the attachment of SO₄^2- ions on the surface of CNC from -1.0 mV to about -30 mV, with the increment of the reaction time from 20 min to 45 min, which proved the higher stability of CNC suspension. Crystallinity increased from 80% to 90% when the reaction time was increased from 20 to 45 min, respectively, while a crystallite size from 2.705 to 4.56 nm was obtained with an increment of the acid concentration. Acid hydrolysis enhanced crystallinity but attenuated the temperature corresponding to major decomposition (Tmax) at 260 °C and the beginning of degradation (Ti) at 200 °C due to the attachment of SO₄^2- ions on the surface, which decreased the thermal stability of CNC. The second degradation at 360 °C indicated the stable crystal structure of CNC. The endothermic peak at 255 °C in the DTA study provided evidence of sulfated nanocrystal decomposition and the recrystallization of cellulose I to cellulose II, the most stable structure among the other four celluloses. The proposed easy-to-reproduce method can successfully and efficiently produce CNCs from waste jute fibers in a straightforward way.

Challenges and perspectives of green-like lignocellulose pretreatments selectable for low-cost biofuels and high-value bioproduction

Lignocellulose represents the most abundant carbon-capturing substance that is convertible for biofuels and bioproduction. Although biomass pretreatments have been broadly applied to reduce lignocellulose recalcitrance for enhanced enzymatic saccharification, they mostly require strong conditions with potential secondary waste release. By classifying all major types of pretreatments that have been recently conducted with different sources of lignocellulose substrates, this study sorted out their distinct roles for wall polymer extraction and destruction, leading to the optimal pretreatments evaluated for cost-effective biomass enzymatic saccharification to maximize biofuel production. Notably, all undigestible lignocellulose residues are also aimed for effective conversion into value-added bioproduction. Meanwhile, desired pretreatments were proposed for the generation of highly-valuable nanomaterials such as cellulose nanocrystals, lignin nanoparticles, functional wood, carbon dots, porous and graphitic nanocarbons. Therefore, this article has proposed a novel strategy that integrates cost-effective and green-like pretreatments with desirable lignocellulose substrates for a full lignocellulose utilization with zero-biomass-waste liberation.

Photocatalytic and antibacterial activity of graphene oxide/cellulose-doped TiO2 quantum dots: in silico molecular docking studies

Graphene oxide (GO) and cellulose nanocrystal (CNC)-doped TiO₂ quantum dots (QDs) were effectively synthesized by employing the co-precipitation method for the degradation of dyes and antimicrobial applications. A series of characterizations, i.e., XRD, FTIR, UV-visible spectroscopy, EDS, FE-SEM, and HR-TEM, was used to characterize the prepared samples. A reduction in PL intensity was observed, while the band gap energy (E _g) decreased from 3.22 to 2.96 eV upon the incorporation of GO/CNC in TiO₂. In the Raman spectra, the D and G bands were detected, indicating the presence of graphene oxide in the composites. Upon doping, the crystallinity of TiO₂ increased. HR-TEM was employed to estimate the interlayer d-spacing of the nanocomposites, which matched well with the XRD data. The photocatalytic potential of the prepared samples was tested against methylene blue, methylene violet, and ciprofloxacin (MB:MV:CF) when exposed to visible light for a certain period. The antibacterial activity of GO/CNC/TiO₂ QDs against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) bacteria in vitro was tested to determine their potential for medicinal applications. The molecular docking investigations of CNC-TiO₂ and GO/CNC-doped TiO₂ against DNA gyrase and FabI from E. coli and S. aureus were found to be consistent with the results of the in vitro bactericidal activity test. We believe that the prepared nanocomposites will be highly efficient for wastewater treatment and antimicrobial activities.

The Simultaneous Production of Two Distinct Types of Cellulose Nanocrystals

We develop a route to prepare two types of cellulose nanocrystals (CNCs, CNC1 and CNC2) from a unique biomass resource, the fruit shell of Camellia oleifera Abel (SCOA), by integrating sulfuric acid hydrolysis and high-pressure homogenization and examine the effects of hydrolysis time on characteristics of the CNCs during the process. The CNCs exhibit different evolutions in size, morphology, surface charge, and crystallinity with increasing hydrolysis time. While both the CNCs have high crystallinity, CNC1 is of rod-like character with a relatively low aspect ratio, and CNC2 exhibits a hairy appearance with a high aspect ratio. We highlight that controlled acid hydrolysis contributes to the formation of weak spots with an increased susceptibility for homogenizing cellulosic solid residues into hairy CNCs. This is a good step toward tailoring CNC properties in a conventional and scalable approach to maximize their potential applications.

Fiber-Based Biopolymer Processing as a Route toward Sustainability

Some of the most abundant biomass on earth is sequestered in fibrous biopolymers like cellulose, chitin, and silk. These types of natural materials offer unique and striking mechanical and functional features that have driven strong interest in their utility for a range of applications, while also matching environmental sustainability needs. However, these material systems are challenging to process in cost-competitive ways to compete with synthetic plastics due to the limited options for thermal processing. This results in the dominance of solution-based processing for fibrous biopolymers, which presents challenges for scaling, cost, and consistency in outcomes. However, new opportunities to utilize thermal processing with these types of biopolymers, as well as fibrillation approaches, can drive renewed opportunities to bridge this gap between synthetic plastic processing and fibrous biopolymers, while also holding sustainability goals as critical to long-term successful outcomes.

MoS2/cellulose-doped ZnO nanorods for catalytic, antibacterial and molecular docking studies

Cellulose nanocrystals (CNCs) and molybdenum disulphide (MoS₂) incorporated into ZnO nanorods (NRs) were synthesized via a chemical precipitation route at room temperature. All concerned samples were characterized to examine their optical properties, elemental composition, phase formation, surface morphology and functional group presence. The aim of this research was to enhance the catalytic properties of ZnO by co-doping with various concentrations of CNCs and MoS₂ NRs. It was renowned that doped ZnO NRs showed superior catalytic activity compared to bare ZnO NRs. Statistically significant (p < 0.05) inhibition zones for samples were recorded for E. coli and S. aureus at low and high concentrations, respectively. The in vitro bactericidal potential of ZnO-CNC and ZnO-CNC-MoS₂ nanocomposites was further confirmed through in silico molecular docking predictions against the DHFR and DHPS enzymes of E. coli and S. aureus. Molecular docking studies suggested the inhibition of these enzyme targets by CNC nanocomposites as a possible mechanism governing their bactericidal activity.

Novel Ag/cellulose-doped CeO2 quantum dots for efficient dye degradation and bactericidal activity with molecular docking study

In the present study, the novel Ag/cellulose nanocrystal (CNC)-doped CeO₂ quantum dots (QDs) with highly efficient catalytic performance were synthesized using one pot co-precipitation technique, which were then applied in the degradation of methylene blue and ciprofloxacin (MBCF) in wastewater. Catalytic activity against MBCF dye was significantly reduced (99.3%) for (4%) Ag dopant concentration in acidic medium. For Ag/CNC-doped CeO₂ vast inhibition domain of G-ve was significantly confirmed as (5.25-11.70 mm) and (7.15-13.60 mm), while medium- to high-concentration of CNC levels were calculated for G + ve (0.95 nm, 1.65 mm), respectively. Overall, (4%) Ag/CNC-doped CeO₂ revealed significant antimicrobial activity against G-ve relative to G + ve at both concentrations, respectively. Furthermore, in silico molecular docking studies were performed against selected enzyme targets dihydrofolate reductase (DHFR), dihydropteroate synthase (DHPS), and DNA gyrase belonging to folate and nucleic acid biosynthetic pathway, respectively to rationalize possible mechanism behind bactericidal potential of CNC-CeO₂ and Ag/CNC-CeO₂.

Cellulose nanocrystals: Pretreatments, preparation strategies, and surface functionalization

Cellulose nanocrystals (CNCs) have attracted great interest from researchers from academic and industrial areas because of their interesting structural features and unique physicochemical properties, such as magnificent mechanical strength, high surface area, and many hydroxyl groups for chemical modification, low density, and biodegradability. CNCs are an outstanding contender for applications in assorted fields comprehensive of, e.g., biomedical, electronic gadgets, water purifications, nanocomposites, membranes. Additionally, a persistent progression is going on in the extraction and surface modification of cellulose nanocrystals to fulfill the expanding need of producers to fabricate cellulose nanocrystals-based materials. In this review, the foundation of nanocellulose that emerged from lignocellulosic biomass and recent development in extraction/preparation of cellulose nanocrystals and different types of cellulose nanocrystal surface modification techniques are summed up. The different sorts of cellulose modification reactions that have been discussed are acetylation, oxidations, esterifications, etherifications, ion-pair formation, hydrogen bonding, silanization, nucleophilic substitution reactions, and so forth. The mechanisms of surface functionalization reactions are also introduced and considered concerning the impact on the reactions. Moreover, the primary association of cellulose and different forms of nanocellulose has likewise been examined for beginners in this field.

Recent Advances in the Synthesis of Nanocellulose Functionalized–Hybrid Membranes and Application in Water Quality Improvement

The increasing discharge of voluminous non or partially treated wastewaters characterized by complex contaminants poses significant ecological and health risks. Particularly, this practice impacts negatively on socio-economic, technological, industrial, and agricultural development. Therefore, effective control of water pollution is imperative. Over the past decade, membrane filtration has been established as an effective and commercially attractive technology for the separation and purification of water. The performance of membrane-based technologies relies on the intrinsic properties of the membrane barrier itself. As a result, the development of innovative techniques for the preparation of highly efficient membranes has received remarkable attention. Moreover, growing concerns related to cost-effective and greener technologies have induced the need for eco-friendly, renewable, biodegradable, and sustainable source materials for membrane fabrication. Recently, advances in nanotechnology have led to the development of new high-tech nanomaterials from natural polymers (e.g., cellulose) for the preparation of environmentally benign nanocomposite membranes. The synthesis of nanocomposite membranes using nanocelluloses (NCs) has become a prominent research field. This is attributed to the exceptional characteristics of these nanomaterials (NMs) namely; excellent and tuneable surface chemistry, high mechanical strength, low-cost, biodegradability, biocompatibility, and renewability. For this purpose, the current paper opens with a comprehensive yet concise description of the various types of NCs and their most broadly utilized production techniques. This is closely followed by a critical review of how NC substrates and their surface-modified versions affect the performance of the fabricated NC-based membranes in various filtration processes. Finally, the most recent processing technologies for the preparation of functionalized NCs-based composite membranes are discussed in detail and their hybrid characteristics relevant to membrane filtration processes are highlighted.

Facile biosynthesis of synthetic crystalline cellulose nanoribbon from maltodextrin through a minimized two-enzyme phosphorylase cascade and its application in emulsion

Nanocellulose has many promising applications such as a green ingredient for Pickering emulsion. Traditional strategies to produce nanocellulose, which are acid or enzymatic hydrolysis and mechanical methods on natural complicated cellulose, are hard to control and can result in significant pollutants during the processes. Herein, we demonstrated a facile and sustainable method for the biocatalytic production of insoluble synthetic crystalline cellulose nanoribbon (CCNR) from cheap maltodextrin by coupling α-glucan phosphorylase (αGP) and cellodextrin phosphorylase (CDP) using cellobiose as a primer. And by optimizing the combination of different αGP and CDP, it turned out that the optimal enzyme combination is αGP from Thermotoga maritime and CDP from Clostridium thermocellum, in which CDP was attached to a family 9 cellulose-binding module. The product yield and degree of polymerization (DP) of insoluble synthetic CCNR was affected by the primer concentration at a fixed concentration of maltodextrin. After optimization of reaction conditions, the highest product yield of insoluble synthetic CCNR was 44.92 % and the highest DP of the insoluble synthetic CCNR was 24 from 50 g 1^-1 maltodextrin. This insoluble synthetic CCNR can be used as a Pickering emulsions stabilizer, showing excellent emulsifiability. This study provides a promising alternative for cost-efficient production of insoluble synthetic CCNR which was used as a green emulsion stabilizer.

Enzymatically produced cellulose nanocrystals as reinforcement for waterborne polyurethane and its applications

Waterborne polyurethanes (WBPUs) have been proposed as ecofriendly elastomers with several applications in coatings and adhesives. WBPU's physicochemical properties can be enhanced by the addition of cellulose nanocrystals (CNCs). The way CNCs are isolated has a strong effect on their properties and can determine their role as reinforcement. In this work, CNCs produced using ancestral endoglucanase (EnCNCs) were used as reinforcement for WBPU and compared with CNC produced by sulfuric acid hydrolysis (AcCNC). The enzymatic method produced highly thermostable and crystalline CNCs. The addition of small contents of EnCNCs improved the thermomechanical stability and mechanical properties of WBPUs, even better than commercial AcCNCs. Besides, WBPU reinforced by adding EnCNCs was studied as a coating for paper materials, increasing its abrasion resistance and as electrospun nanocomposite mats where EnCNCs helped maintaining the morphology of the fibers.

The valorization of municipal grass waste for the extraction of cellulose nanocrystals

The study reports on the valorization of municipal grass waste (MGW) for the extraction of cellulose nanocrystals (CNCs), as an eco-friendly and sustainable low-cost precursor for cellulose nanomaterial production. The raw MGW was subjected to boiling in water pretreatment, and alkali and bleaching treatments for the extraction of cellulose fibers, followed by isolation of the CNCs through a conventional acid hydrolysis technique. Fourier transform infrared spectroscopy was used to analyze the cellulose fibers extracted while scanning electron microscopy and transmission electron microscopy images confirmed the presence of cellulose fibers and CNCs, respectively. The chemical composition of MGW was ascertained through the TAPPI-222 om-02 standard for lignin content and determination of α-cellulose. The diameters of CNCs are in the range of 5–15 nm with the length ranging from 100 nm to 500 nm, while a crystallinity index of 58.2% was determined from X-ray diffraction analysis. The production of CNCs from MGW is an avenue to convert green waste into a value-added product, in addition to reducing the volume of cumulative waste in the environment.

The production of CNCs from MGW is an avenue to convert green waste into a value-added product.

Maximizing production of cellulose nanocrystals and nanofibers from pre-extracted loblolly pine kraft pulp: a response surface approach

This study aims to optimize strong acid hydrolysis-based production of cellulose nanocrystals (CNCs) and cellulose nanofibers (CNFs) from pre-extracted and fully bleached kraft pulp of loblolly pinewood, the most abundant and commercially significant softwood species in southeastern United States. The effect of four parameters, including acid concentration, temperature, duration and pulp particle size, on the yield and properties of CNCs was investigated using the central composite design (CCD) of response surface methodology (RSM) for process optimization. While CNC yield was significantly affected by acid concentration and hydrolysis temperature and was adequately explained by an empirical model, none of the characteristic properties of CNCs, including crystallinity index, surface charge and particle size, displayed any strong correlation to the process parameters within the experimental ranges tested. At different hydrolysis severities, we not only analyzed the waste streams to determine the extent of holocellulose degradation, but also evaluated the properties of leftover partially hydrolyzed pulp, called cellulosic solid residues (CSR), to gauge its potential for CNF production via mechanical fibrillation. Conditions that maximized CNC yields (60% w/w) were 60% acid concentration, 58 °C, 60 min and 40 mesh particle size. Twenty percent (w/w) of the pulp was degraded under these conditions. On the other hand, conditions that maximized CSR yields (60% w/w) were 54% acid, 45 °C, 90 min and 20 mesh particle size, which also produced 15% CNCs, caused minimal pulp degradation (< 5%) and imparted sufficient surface charge such that CSR was easily microfluidized into CNFs. Therefore, the strong acid hydrolysis process could be tuned to maximize the production of cellulose nanocrystals and nanofibers and obtain two products with different properties and applications through the process optimization.

Facile extraction of cellulose nanocrystals

A simple process for extracting cellulose nanocrystals (CNCs) is proposed that only uses high-pressure homogenization (HPH) controlling a process temperature. The proposed process was assessed and compared with normal production through acidic hydrolysis. Temperature-controlled HPH produced CNCs with high crystallinity, which linearly increased with increasing process temperature over 20 passes. The CNCs had uniform widths and lengths in the ranges of 4-14 nm and 60-320 nm, respectively. Undesirable chemical reaction can be avoided with the proposed process because no chemical was used to promote the CNC extraction. This method is an efficient and sustainable green approach to CNC production.

Current characterization methods for cellulose nanomaterials

A new family of materials comprised of cellulose, cellulose nanomaterials (CNMs), having properties and functionalities distinct from molecular cellulose and wood pulp, is being developed for applications that were once thought impossible for cellulosic materials. Commercialization, paralleled by research in this field, is fueled by the unique combination of characteristics, such as high on-axis stiffness, sustainability, scalability, and mechanical reinforcement of a wide variety of materials, leading to their utility across a broad spectrum of high-performance material applications. However, with this exponential growth in interest/activity, the development of measurement protocols necessary for consistent, reliable and accurate materials characterization has been outpaced. These protocols, developed in the broader research community, are critical for the advancement in understanding, process optimization, and utilization of CNMs in materials development. This review establishes detailed best practices, methods and techniques for characterizing CNM particle morphology, surface chemistry, surface charge, purity, crystallinity, rheological properties, mechanical properties, and toxicity for two distinct forms of CNMs: cellulose nanocrystals and cellulose nanofibrils.

Recent progress in cellulose nanocrystals: sources and production

Cellulose nanocrystals, a class of fascinating bio-based nanoscale materials, have received a tremendous amount of interest both in industry and academia owing to its unique structural features and impressive physicochemical properties such as biocompatibility, biodegradability, renewability, low density, adaptable surface chemistry, optical transparency, and improved mechanical properties. This nanomaterial is a promising candidate for applications in fields such as biomedical, pharmaceuticals, electronics, barrier films, nanocomposites, membranes, supercapacitors, etc. New resources, new extraction procedures, and new treatments are currently under development to satisfy the increasing demand of manufacturing new types of cellulose nanocrystals-based materials on an industrial scale. Therefore, this review addresses the recent progress in the production methodologies of cellulose nanocrystals, covering principal cellulose resources and the main processes used for its isolation. A critical and analytical examination of the shortcomings of various approaches employed so far is made. Additionally, structural organization of cellulose and nomenclature of cellulose nanomaterials have also been discussed for beginners in this field.