Evaluation of Extraction Techniques for Recovery of Microalgal Lipids under Different Growth Conditions

Microalgal lipids contain a wide array of liposoluble bioactive compounds, but lipid extraction remains a critical limitation for their commercial use. An accelerated solvent extraction (ASE) was used to extract lipids from Chlamydomonas reinhardtii, Arthrospira platensis (Spirulina), and Chlorella vulgaris grown under either standard or nitrogen depletion conditions. Under standard growth conditions, ASE using methanol:chloroform (2:1), methyl tert-butyl ether (MTBE):methanol:water, and ethanol at 100 °C resulted in the highest recovery of total lipids (352 ± 30, 410 ± 32, and 127 ± 15 mg/g biomass from C. reinhardtii, C. vulgaris, and A. platensis, respectively). Similarly, the highest total lipid and triacylglycerols (TAGs) recovery from biomass cultivated under nitrogen depletion conditions was found at 100 °C using methanol:chloroform, for C. reinhardtii (total, 550 ± 21; TAG, 205 ± 2 mg/g biomass) and for C. vulgaris (total, 612 ± 29 mg/g; TAG, 253 ± 7 mg/g biomass). ASE with MTBE:methanol:water at 100 °C yielded similar TAG recovery for C. reinhardtii (159 ± 6 mg/g) and C. vulgaris (200 ± 4 mg/g). Thus, MTBE:methanol:water is suggested as an alternative substitute to replace hazardous solvent mixtures for TAGs extraction with a much lower environmental impact. The extracted microalgal TAGs were rich in palmitic (C16:0), stearic (C18:0), oleic (C18:1,9), linoleic (C18:2n6), and α-linolenic (C18:3n3) acids. Under nitrogen depletion conditions, increased palmitic acid (C16:0) recovery up to 2-fold was recorded from the biomasses of C. reinhardtii and C. vulgaris. This study demonstrates a clear linkage between the extraction conditions applied and total lipid and TAG recovery.

Fatty Acid Composition and Cytotoxic Activity of Lipid Extracts from Nannochloropsis gaditana Produced by Green Technologies

Microalgae are alternatives and sustainable sources of omega-3 long chain-polyunsaturated fatty acids (LC-PUFA). However, the eco-friendly extraction of these bioactives remains unexplored. In this work, the use of enzyme-based methods in combination with ultrasounds was evaluated as green approaches to extract the omega-3 lipids from Nannochloropsis gaditana. Three commercial enzymatic solutions (Viscozyme® L, Celluclast® 1.5 L, and Saczyme®) were investigated, and results were compared with the traditional Folch method. A promising extraction approach was developed by using Saczyme®, achieving a lipid yield of 25.7% ± 0.5, comparable to the traditional method (27.3% ± 0.7) (p > 0.05). Similar omega-3 content was found by GC−MS analysis for both lipid extracts (30.2% ± 2.4 and 29.3% ± 0.8 for the green and the traditional method, respectively), showing that the green approaches did not affect the fatty acid profile. Moreover, the cytotoxic activity of produced lipids was assessed by comparing human colon cancer cells (HCT-116) and epithelial nontumorigenic immortalized cells (HCEC-1CT). Results suggest that the lipid extracts have a selective effect, reducing the viability of the colon carcinoma cells but not the nontumorigenic cells. Thus, this study provides new eco-innovative approaches for extracting the omega-3 LC-PUFA from microalgae with promising biological properties.

Advances in Lipid Extraction Methods-A Review

Extraction of lipids from biological tissues is a crucial step in lipid analysis. The selection of appropriate solvent is the most critical factor in the efficient extraction of lipids. A mixture of polar (to disrupt the protein-lipid complexes) and nonpolar (to dissolve the neutral lipids) solvents are precisely selected to extract lipids efficiently. In addition, the disintegration of complex and rigid cell-wall of plants, fungi, and microalgal cells by various mechanical, chemical, and enzymatic treatments facilitate the solvent penetration and extraction of lipids. This review discusses the chloroform/methanol-based classical lipid extraction methods and modern modifications of these methods in terms of using healthy and environmentally safe solvents and rapid single-step extraction. At the same time, some adaptations were made to recover the specific lipids. In addition, the high throughput lipid extraction methodologies used for liquid chromatography-mass spectrometry (LC-MS)-based plant and animal lipidomics were discussed. The advantages and disadvantages of various pretreatments and extraction methods were also illustrated. Moreover, the emerging green solvents-based lipid extraction method, including supercritical CO2 extraction (SCE), is also discussed.

Microalgae Cultivation in Palm Oil Mill Effluent (POME) Treatment and Biofuel Production

Palm oil mill effluent (POME) is the wastewater produced during the palm oil sterilization process, which contains substantial amounts of nutrients and phosphorous that are harmful to the environment. High BOD and COD of POME are as high as 100,000 mg/L, which endanger the environment. Effective pre-treatment of POME is required before disposal. As microalgae have the ability of biosorption on nutrients and phosphorous to perform photosynthesis, they can be utilized as a sustainable POME treatment operation, which contributes to effective biofuel production. Microalgae species C. pyrenoidosa has shown to achieve 68% lipid production along with 71% nutrient reduction in POME. In this study, a brief discussion about the impacts of POME that will affect the environment is presented. Additionally, the potential of microalgae in treating POME is evaluated along with its benefits. Furthermore, the condition of microalgae growth in the POME is also assessed to study the suitable condition for microalgae to be cultivated in. Moreover, experimental studies on characteristics and performance of microalgae are being evaluated for their feasibility. One of the profitable applications of POME treatment using microalgae is biofuel production, which will be discussed in this review. However, with the advantages brought from cultivating microalgae in POME, there are also some concerns, as microalgae will cause pollution if they are not handled well, as discussed in the last section of this paper.

Recovery of Bioactive Compounds from Hazelnuts and Walnuts Shells: Quantitative-Qualitative Analysis and Chromatographic Purification

Hazelnut (HS) and walnut (WS) shells, an abundant by-product of the processing industries of these edible nuts, are traditionally considered as a low-value waste. However, they are a source of valuable compounds with an interesting chemical profile for the chemical and pharmaceutical sectors. In this study, the lipophilic and hydrophilic extracts present in HS and WS were quantified and identified, then the polar fractions were chromatographically separated, and their antioxidant capacity was studied. The experimental work includes the isolation of crude lipophilic and hydrophilic extracts by an accelerated extraction process, chromatographic analysis (gas chromatography-flame ionization (GC-FID), GC-mass spectroscopy (GC-MS), high-performance size-exclusion chromatography (HPSEC), thin-layer chromatography (TLC)), and quantification of the components. In addition, a thorough compositional characterization of the subgroups obtained by flash chromatography and their antioxidant capacity was carried out. The gravimetric concentrations showed different lipophilic/hydrophilic ratios (0.70 for HS and 0.23 for WS), indicating a higher proportion of polar compounds in WS than in HS. Moreover, the lipophilic extracts were principally composed of short-chain fatty acids (stearic, palmitic, and oleic acid), triglycerides, and sterols. The polar fractions were screened by thin-layer chromatography and then separated by flash chromatography, obtaining fractions free of fatty acids and sugar derivatives (97:3 in HS and 95:5 in WS), and mixtures richer in phenolic compounds and flavonoids such as guaiacyl derivatives, quercetin, pinobanksin, and catechin. The most polar fractions presented a higher antioxidant capacity than that of the crude extracts.

Pressurized liquid extraction followed by liquid chromatography coupled to a fluorescence detector and atmospheric pressure chemical ionization mass spectrometry for the determination of benzo(a)pyrene metabolites in liver tissue of an animal model of colon cancer

Since metabolism is implicated in the carcinogenesis of toxicants, an efficient extraction method together with an analytical method is warranted to quantify tissue burdens of a carcinogen and/or its metabolites. Therefore, the aim of this study was to validate a pressurized liquid extraction (PLE) method for measuring metabolites of benzo(a)pyrene [B(a)P; a food-borne carcinogen] from tissue samples. The sample extraction was performed separately by PLE and liquid-liquid extraction (LLE). PLE followed by high-performance liquid chromatography coupled to online fluorescence detector (HPLC-FLD) was used to quantify separated analytes; and by ultra-high-performance liquid chromatography (UHPLC) coupled to atmospheric pressure chemical ionization tandem mass spectrometry (UHPLC-APCI-MS/MS) were used for confirmation purposes. The UHPLC-MS/MS was set-up in the atmospheric pressure chemical ionization (APCI) positive interface with selective reaction monitoring (SRM). The analytical performance characteristics of the PLE technique was assessed at different temperatures, pressure, number of cycles and solvent types. A methanol + chloroform + water mixture (30:15:10, v/v/v) yielded greater recoveries at an extraction temperature range of 60-80°C, pressure of 10 MPa and an extraction time of 10 min. The PLE method was validated by the analysis of spiked tissue samples and measuring recoveries and limits of quantitation for the analytes of interest using HPLC-FLD equipment. The optimized PLE-HPLC-FLD method was used to quantify the concentrations of B(a)P metabolites in liver samples obtained from a colon cancer animal model. Overall, PLE performed better in terms of extraction efficiency, recovery of B(a)P metabolites and shortened sample preparation time when compared with the classic LLE method.

Extraction and bioprocessing with supercritical fluids

Supercritical fluid (SCF) technologies have emerged as a real alternative to various natural product extraction processes and pharmaceutical production to obtain micronized particles, coprecipitates, nanocomposite polymer structures and liposomes, in addition to other increasingly larger applications described in literature. In the present work, a brief literature review of the application of supercritical fluid extraction (SFE) is presented. This is evidenced by several publications and patents, contributions from several countries and the increase of industries around the world dedicated to this technique. Next, we aim to focus the analysis of SFE on a review of the literature applied to microalgae as a substitute primitive feedstock due to its high growth rate, valuable biologically active lipophilic substances, and photosynthetic efficiency without competition with food sources or needs of arable lands. We finally discussing an SCF bioprocess with a very new perspective for liposome production focalized on its potential at industrial scale.

Improvement of Bio-Oil and Nitrogen Recovery from Microalgae Using Two-Stage Hydrothermal Liquefaction with Solid Carbon and HCl Acid Catalysis

Bio-oil production from microalgae by using hydrothermal liquefaction (HTL) has been conducted extensively in the last decade. In this work, we conducted two-stage HTL of a microalga (Fistulifera solaris, JPCC DA0580) in the presence of 5.0 g/L carbon solid acid or a 0.02-0.50 M HCl catalyst to increase bio-oil yield and nitrogen recovery into the aqueous phase (AP). The first stage (HTL 1), to hydrolyze proteins, carbohydrates, and lipids and elute nitrogen components into the AP, was conducted at 100-250 °C for 30-120 min. The second stage (HTL 2), to produce the bio-oil, was conducted at 280-320 °C for 0-30 min. The best conditions to obtain a high bio-oil yield and NH₄ ⁺ recovery in the AP were 200 °C and 30 min of residence time for HTL 1 and 320 °C and 0 min residence time for HTL 2. We found that 0.50 M HCl decreased the bio-oil yield while greatly increasing NH₄ ⁺ in the AP and decreasing the nitrogen content in the bio-oil. This was probably due to the catalytic effect of HCl promoting hydrolysis of protein and deamination of amino acids during HTL 1. The fractions of water-soluble products were greatly increased by performing HTL 2 in neutral conditions while this maintained low nitrogen content in the bio-oil. From GC-MS analyses of the bio-oil, it was observed that, by using 0.50 M HCl, peak intensities of all the GC peaks decreased and MS spectra of amines decreased. The carbon solid acid had an insignificant influence on bio-oil and NH₄ ⁺ yields.

Pressurized liquid extraction with ethanol as a green and efficient technology to lipid extraction of Isochrysis biomass

This work was the first time to establish a green pressurized liquid extraction (PLE) process to extract microalgal lipids from Isochrysis biomass. PLE with ethanol exhibited superior lipid extraction performance in comparison to Soxhlet and Folch methods and PLE with n-hexane. To reduce the cost in ethanol utilization, ethanol concentration was optimized and found that PLE with 90% ethanol concentration obtained the highest lipid extraction efficiency (41.5 wt%) and total fatty acids (TFAs) recovery value (92.17 wt%) using Isochrysis sp. biomass. Results about lipid class detected by TLC-FID technique showed that ethanol concentration distinctly affected the content of lipidic class during lipid extraction by PLE. Similarly, the process with 90% ethanol concentration achieved over 90 wt% of TFAs recovery values with three different Isochrysis species. Overall, PLE process mediated with ethanol was a promising approach to extract Isochrysis-derived lipids from sustainable microalgal biomass for food application.

Determination of Microalgal Lipid Content and Fatty Acid for Biofuel Production

Biofuels produced from microalgal biomass have received growing worldwide recognition as promising alternatives to conventional petroleum-derived fuels. Among the processes involved, the downstream refinement process for the extraction of lipids from biomass greatly influences the sustainability and efficiency of the entire biofuel system. This review summarizes and compares the current techniques for the extraction and measurement of microalgal lipids, including the gravimetric methods using organic solvents, CO₂-based solvents, ionic liquids and switchable solvents, Nile red lipid visualization method, sulfo-phospho-vanillin method, and the thin-layer chromatography method. Each method has its own competitive advantages and disadvantages. For example, the organic solvents-based gravimetric method is mostly used and frequently employed as a reference standard to validate other methods, but it requires large amounts of samples and is time-consuming and expensive to recover solvents also with low selectivity towards desired products. The pretreatment approaches which aimed to disrupt cells and support subsequent lipid extraction through bead beating, microwave, ultrasonication, chemical methods, and enzymatic disruption are also introduced. Moreover, the principles and procedures for the production and quantification of fatty acids are finally described in detail, involving the preparation of fatty acid methyl esters and their quantification and composition analysis by gas chromatography.

Use of solvent mixtures for total lipid extraction of Chlorella vulgaris and gas chromatography FAME analysis

Lipid extraction is the bottleneck step for algae-based biodiesel production. Herein, 12 solvent mixture systems (mixtures of three non-polar and two polar organic solvents) were examined to evaluate their effects on the total lipid yield from Chlorella vulgaris (C. vulgaris). Moreover, the extraction yields of three solvent systems with maximum extraction efficiency of esterifiable lipids were determined by acidic transesterification and GC-FID analysis. Three solvent systems, which resulted in a higher extraction yield, were further subjected to fatty acid methyl ester (FAME) analysis. The total lipid extraction yields (based on dry biomass) were (38.57 ± 1.51), (25.33 ± 0.58), and (25.17 ± 1.14) %, for chloroform-methanol (1:2) (C1M2), hexane-methanol (1:2) (H1M2), and chloroform-methanol (2:1) (C2M1), respectively. The extraction efficiency of C1M2 was approximately 1.5 times higher than H1M2 and C2M1, whereas the FAME profile of extracted lipids by H1M2 and C1M2 were almost identical. Moreover, the esterifiable lipid extraction yields of (18.14 ± 2.60), (16.66 ± 0.35), and (13.22 ± 0.31) % (based on dry biomass) were obtained for C1M2, H1M2, and C2M1 solvent mixture systems, respectively. The biodiesel fuel properties produced from C. vulgaris were empirically predicted and compared to that of the EN 14214 and ASTM 6751 standard specifications.