Comparison of three different structures of zeolites prepared by template-free hydrothermal method and its CO2 adsorption properties

In this study, zeolite sodalite SOD (50NaO₂:Al₂O₃:5SiO₂), zeolite LTA (2NaO₂:Al₂O₃:1.926SiO₂) and zeolite FAU (16NaO₂:Al₂O₃:4SiO₂) of different structures were synthesized successfully through simple conventional hydrothermal crystallization technique without using any template agent. Morphological analysis of three different types of zeolites revealed that the samples exhibit three different shapes such as the "Raspberry-like", "Dice" cube like and "Octahedral" shaped morphology respectively. The thermal stability was found to be about 4.8%, 14.6% and 20.5% for the synthesized zeolites SOD, LTA and FAU respectively. From the N₂ adsorption-desorption studies, it was observed that adsorption types IV and I correspond to the synthesized samples. CO₂ adsorption by the synthesized zeolite SOD, LTA and FAU were examined in the pressure range from 0 to 101.325 kPa at a constant temperature of 297.15 K. The highest adsorption capacity of 3.7 mmol/g was obtained for zeolite FAU. The synthesized zeolite was studied using a nonlinear regression curve fit to determine the adsorption isotherm model using Langmuir and Freundlich isotherm model. It has been found that the synthesized zeolites have a large electric field gradient due to which they can strongly adsorb quadrupole of CO₂ molecules.

Effects of Si/Al Ratios on the Bulk-Type Zeolite Formation Using Synthetic Metakaolin-Based Geopolymer with Designated Composition

In this paper, synthetic metakaolin with fixed composition (Al2O3·2SiO2) was produced by a simple chemosynthetic route. The chemosynthetic metakaolin can eliminate the influence of impurities in metakaolin from natural kaolin minerals. The synthetic metakaolin together with NaOH and SiO2-sol were used to prepare Na-based geopolymer precursors with various molar ratios of Si/Al. The molar ratios of Si/Al from 1 to 2 were tailored by adding different contents of SiO2-sol. Zeolite/geopolymer composites or monolith-type zeolite were successfully fabricated from synthetic metakaolin-based geopolymer through a hydrothermal process. The effects of Si/Al ratios on the phase composition and microstructure of the produced zeolite/geopolymer composites or zeolites were studied. The results proved that the composition of synthetic metakaolin and geopolymer precursors can be facilely tuned, and the monolithic geopolymer precursors can be mostly, or even totally, transformed into zeolite after hydrothermal treatment.

The Effects of NaOH Concentration on the Hydrothermal Synthesis of a Hydroxyapatite–Zeolite Composite Using Blast Furnace Slag

This study investigated the effect of NaOH concentration on the assemblage, crystallinity, and dimension of crystalline phases in hydroxyapatite–zeolite composites made with blast furnace slag. X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy measurement, scanning electron microscopy (SEM), and nitrogen adsorption–desorption tests were conducted to characterize the synthesized composites. In addition, the cesium adsorption potential of the synthesized composites was evaluated to assess the feasibility of using hydroxyapatite–zeolite composites synthesized from blast furnace slag. The composite samples using a 3 M NaOH solution showed the formations of Na-P1 and Faujasite (FAU) zeolites along with hydroxyapatite, which led to the highest adsorption capacity for cesium (44.90 mg/g).

Effect of H2O Activity on Zeolite Formation

In an effort to understand the effects of H₂O activity on zeolite formation, we have synthesized LTA zeolite using a combination of freezing processes and varying drying temperatures. Sodium aluminate and sodium silicate were used to form LTA zeolite, according to the IZA (International Zeolite Association) protocol. The synthesis steps were modified by adding the precursor frozen process by a rapid liquid nitrogen (-196 °C) treatment or slow conventional freezer treatment (-20 °C). The samples were subsequently sonicated and then dried at 80 °C or 40 °C. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were performed on the samples immediately after the drying process as well as after 2 weeks and 1 month of aging the solid products. The results indicated that LTA zeolite does not form. The silica-alumina precursor after both freezing processes and after being dried at 80 °C showed the presence of sodalite displaying stable behavior over time. Both sets of samples dried at 40 °C and did not show the presence of zeolite immediately after the drying process. However, after 2 weeks, the liquid nitrogen-frozen precursor was characterized by the presence of EMT whereas zeolites never formed in the -20 °C samples. These results suggest that freezing processes differently control the H₂O activity during the drying and aging processes in the solid state. Thus, although the precursor chemical composition is the same, the type of zeolite formed is different.

Ironmaking and Steelmaking Slags as Sustainable Adsorbents for Industrial Effluents and Wastewater Treatment: A Critical Review of Properties, Performance, Challenges and Opportunities

This paper critically discusses the structure, properties and applications of ironmaking and steelmaking slags and their silicate-based variants as low-cost adsorbents for removing cations and anions from industrial effluents and wastewater. Undoubtedly, the performance of slag-based adsorbents depends on their physical, chemical and phase chemical properties. The presence of crystalline phases, for example, has a significant effect on the adsorption capacity. However, despite their low cost and ubiquity, their chemical and geometric heterogeneity significantly affects the performance and applications of slag-based adsorbents. These challenges notwithstanding, the efficacy of slag-based adsorbents can be significantly enhanced through purposeful activation to increase the specific surface area and density of adsorption sites on the surfaces of adsorbent particles. The synthesis of functionalised adsorbents such as geopolymers, zeolites and layered double hydroxides from silicate and aluminosilicate precursors can also significantly increase the performance of slag-based adsorbents. In addition, the ability to stabilise the dissolved and/or entrained toxic metal species in stable phases in slags, either through controlled post-process fluxing or crystallisation, can significantly enhance the environmental performance of slag-based adsorbents. Most critical in the design of future slag-based adsorbents is the integration of the engineered properties of molten and solidified slags to the recovery and stabilisation of dissolved and/or entrained metals.

The Effects of Temperature on the Hydrothermal Synthesis of Hydroxyapatite-Zeolite Using Blast Furnace Slag

Blast furnace slag, an industrial by-product, is emerging as a potential raw material to synthesize hydroxyapatite and zeolite. In this study, the effects of temperature on the hydrothermal synthesis of hydroxyapatite-zeolite from blast furnace slag were investigated. Specimens were synthesized at different temperatures (room temperature, 50, 90, 120, or 150 °C). The synthesized specimens were analyzed qualitatively and quantitatively via X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), BET/BJH, and scanning electron microscopy/energy dispersive using X-ray analysis (SEM/EDX). It was found that the hydroxyapatite phase was synthesized at all the reaction temperatures, while faujasite type zeolite appeared in the specimens synthesized at 90 and 120 °C. Moreover, faujasite was replaced by hydroxysodalite in the specimens synthesized at 150 °C. Additionally, the crystals of the hydroxyapatite tended to become larger and total crystallinity increased as the reaction temperature increased.

One-Step Synthesis of Hydroxysodalite Using Natural Bentonite at Moderate Temperatures

Ca-bentonite was used as the feedstock material for the synthesis of hydroxysodalite due to its high Al, Si content, good chemical reactivity, and natural abundance. A one-step method is proposed here to fabricate hydroxysodalite in a water bath at moderate temperature. The effects of the Na/Si molar ratio, Si/Al molar ratio, reaction time, and reaction temperature on the synthesis of hydroxysodalite have been systematically investigated here. The crystallizing phases and morphology of the synthetic products were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results showed that the Na/Si molar ratio and reaction temperature both played important roles in controlling the degree of crystallinity of the synthetic hydroxysodalite. The Si/Al molar ratio and reaction time both affect the purity of the synthetic hydroxysodalite. Optimum conditions for synthesizing hydroxysodalite using a one-step water-bath method at moderate temperature are as follows: a Na/Si molar ratio of 12, a Si/Al molar ratio of 1.0, a reaction temperature of 90 °C, and a reaction time of 12 h.

Recycling of typical difficult-to-treat e-waste: Synthesize zeolites from waste cathode-ray-tube funnel glass

The disposal of waste cathode ray-tubes (CRTs) from old televisions and discarded computer monitors has become a major environmental concern worldwide. In this work, an open-loop recycling method was developed to synthesize zeolites using CRT funnel glass as the raw material. The effects of hydrothermal temperatures and pressure, n(SiO₂/Al₂O₃) molar ratios and hydrothermal time on the resulting products were investigated. The results indicated that hydrothermal temperatures and pressure played critical roles in zeolite synthesis. Amorphous phases were detected at lower temperatures (80-100°C) and pressure (0.47-1.01bar) with n(SiO₂/Al₂O₃)=2.0. At the temperature of 110°C (pressure 1.43bar), NaA formed with a mixture of NaP1 and Faujasite. With further increase in the temperature and pressure, the unstable NaA and Faujasite disappeared, and Hydroxysodalite developed. The influence of n(SiO₂/Al₂O₃) ratios on resulting products revealed a single phase of NaA was formed at the ratio of 1.5 and a mixture of NaA and Faujasite at the ratio of 2.0. Prolonging hydrothermal time, however, could promote zeolite crystallization, and NaA gradually developed with an increase in the time from 2 to 6h at n(SiO₂/Al₂O₃)=1.5. By comparison, crystallization phases were observed only when the time was longer than 8h at n(SiO₂/Al₂O₃)=2.0.