Reduced Work Function in Anatase ⟨101⟩ TiO2 Films Self-Doped by O-Vacancy-Dependent Ti3+ Bonds Controlling the Photocatalytic Dye Degradation Performance

TiO2 has the proven capability of catalytically decomposing pollutants under light illumination, thereby embracing potential applications in wastewater management. The photocatalytic dye degradation activity is largely controlled by the optical band gap that dictates the extent of electron-hole pair generation via photon absorption, and the recombination kinetics of charges. In this context, the material's work function governs how easily the charge carriers can be transferred at the dye-adsorbed photocatalytically active sites. Accordingly, nanocrystalline TiO2 thin films are grown in the anatase phase with ⟨101⟩ orientation, using RF magnetron sputtering at 200 °C. Besides studying the film's structural morphology, optical band gap, and elemental composition, the electronic properties are extensively investigated. The work function of the material was controlled by varying the O-vacancy-dependent Ti3+ bonding configuration in the network. It has been demonstrated how the photocatalytic methylene blue dye degradation activity of the nanocrystalline TiO2 films of predominantly the anatase phase improves on reducing the sputtering pressure during deposition. At a low deposition pressure of 20 mTorr, a low work function of ∼4.2 eV of the film, resulting from the formation of a Ti3+-bond through the O vacancies in the network, potentially increases its carrier lifetime and delivers the superior photocatalytic activity (∼82.7% dye degradation with a rate constant of k ∼ 0.0073 min-1) via silently facilitating fast electron transfer from the photocatalyst to the dye in the aqueous solution. The higher stoichiometric film prepared at p = 40 mTorr exhibits an inferior photocatalytic activity (∼20.4% dye degradation with a rate constant of k ∼ 0.0009 min-1), as retarded by its higher work function of ∼4.62 eV, despite retaining a relatively low band gap. Thus, without using any heterojunction or extrinsically doped photocatalyst, the dye degradation can be controlled simply by reducing the work function of nanocrystalline TiO2 thin films via controlling the O-vacancy-dependent Ti3+ bonding in its self-doped network.

Role of polymer template in crystal structure and photoactivity of Cu-TiO2 heterojunction nanostructures towards environmental remediation

Exploring porous heterojunction nanomaterials as a photocatalyst for water depollution strategies towards environmental restoration is exceedingly difficult in the perspective of sustainable chemistry. Herein, we first report a porous Cu-TiO₂ (TC40) heterojunction by using microphase separation of a novel penta-block copolymer (PLGA-PEO-PPO-PEO-PLGA) as a template through an evaporation induced self-assembly (EISA) method having nanorod-like particle shape. Furthermore, three types of photocatalysts were made with or without template polymer to clarify the function of that template precursor on the surface and morphology, as well as which variables are the most critical for a photocatalyst. TC40 heterojunction nanomaterial displayed high BET surface area along with lower band gap value viz.2.98 eV compare the other and all of these features make it a robust photocatalyst for wastewater treatment. In order to improve water quality, we have carried out experiments on the photodegradation of methyl Orange (MO), highly toxic pollutants that cause health hazards and bioaccumulate in the environment. Our catalyst, TC40 exhibits the 100% photocatalytic efficiency towards MO dye degradation in 40 and 360 min at a rate constant of 0.104 ± 0.007 min^-1 and 0.440 ± 0.03 h^-1 under UV + Vis and visible light irradiation respectively.

Waste-Extracted Zn and Ag Co-Doped Spent Catalyst-Extracted V2O5 for Photocatalytic Degradation of Congo Red Dye: Effect of Metal-Nonmetal Co-Doping

The current study applies the eco-friendly principle of “wastes treat wastes”. By swift methods, a composite photocatalyst was prepared from waste-extracted oxides, namely V2O5, Ag, and ZnO. The metal–lixiviant complexes were used as metal precursors, where the lixiviants act as auto-templates and increase the compatibility between the mixed metallic species, and their controlled thermal removal generates pores. The tri-constitute composite catalyst was doped with nitrogen. The constitution, surface composition, and optical properties of the doped catalysts were investigated by XRD, SEM, TEM, BET surface analysis, XPS, diffuse reflectance, and PL spectra. The as-prepared catalysts were employed in the photodegradation of Congo red dye (CR) under visible irradiation at ambient temperature. The degree of Ag dispersion had a significant effect on the bandgap, as did metal and metal-nonmetal co-doping. The efficiency of dye removal changes dramatically with time up to 120 min, after which it begins to decrease. According to the pH effect, the normal pH of Congo red dye (6.12) is optimal. At a catalyst dose of 1 g L−1 and an irradiation period of 120 min, photodegradation efficiency reached 89.9% and 83.4% over [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively. The kinetic study depicted the significant role of mass transfer in the reaction rate. The obtained rate constants were 0.995 mole L−1 S−1 and 0.998 mole L−1 S−1 for [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively.

Facile Synthesis of Gram-Scale Mesoporous Ag/TiO2 Photocatalysts for Pharmaceutical Water Pollutant Removal and Green Hydrogen Generation

This work demonstrates a two-step gram-scale synthesis of presynthesized silver (Ag) nanoparticles impregnated with mesoporous TiO₂ and evaluates their feasibility for wastewater treatment and hydrogen gas generation under natural sunlight. Paracetamol was chosen as the model pharmaceutical pollutant for evaluating photocatalytic performance. A systematic material analysis (morphology, chemical environment, optical bandgap energy) of the Ag/TiO₂ photocatalyst powder was carried out, and the influence of material properties on the performance is discussed in detail. The experimental results showed that the decoration of anatase TiO₂ nanoparticles (size between 80 and 100 nm) with 5 nm Ag nanoparticles (1 wt %) induced visible-light absorption and enhanced charge carrier separation. As a result, 0.01 g/L Ag/TiO₂ effectively removed 99% of 0.01 g/L paracetamol in 120 min and exhibited 60% higher photocatalytic removal than pristine TiO₂. Alongside paracetamol degradation, Ag/TiO₂ led to the generation of 1729 μmol H₂ g^-1 h^-1. This proof-of-concept approach for tandem pollutant degradation and hydrogen generation was further evaluated with rare earth metal (lanthanum)- and nonmetal (nitrogen)-doped TiO₂, which also showed a positive response. Using a combination of ab initio calculations and our new theory model, we revealed that the enhanced photocatalytic performance of Ag/TiO₂ was due to the surface Fermi-level change of TiO₂ and lowered surface reaction energy barrier for water pollutant oxidation. This work opens new opportunities for exploiting tandem photocatalytic routes beyond water splitting and understanding the simultaneous reactions in metal-doped metal oxide photocatalyst systems under natural sunlight.

Effect of Pluronic P103 Concentration on the Simple Synthesis of Ag and Au Nanoparticles and Their Application in Anatase-TiO2 Decoration for Its Use in Photocatalysis

Silver and gold nanoparticles were synthesized under environmentally-friendly reaction conditions by using a biodegradable copolymer and water as a solvent. The triblock copolymer Pluronic P103 was utilized as a stabilizing agent or soft template to produce Ag and Au nanoparticles (NPs) of different sizes. Moreover, in the synthesis of Au NPs, the polymer acted as a reducing agent, decreasing the number of reagents used and consequently the residues produced, hence, rendering the procedure less complicated. It was observed that as the concentration of the polymer increased, the size of the metallic NPs augmented as well. However, AgNPs and AuNPs prepared with 1 and 10 wt% Pluronic P103, respectively, showed a significant decrease in particle size due to the presence of polymeric soft templates. The hybrid materials (metal/polymer) were characterized by UV-Vis spectroscopy, DLS, and TEM. The pre-synthesized nanoparticles were employed to decorate anatase-TiO2, and the composites were characterized by DRS, XRD, BET surface area measurements, the TEM technique with the EDS spectrum, and XPS spectroscopy to demonstrate NPs superficial incorporation. Finally, methylene blue was used as a probe molecule to evidence the effect of NPs decoration in its photocatalytic degradation. The results showed that the presence of the NPs positively affected methylene blue degradation, achieving 96% and 97% removal by utilizing TAg0.1 and TAu10, respectively, in comparison to bare anatase-TiO2 (77%).

Preparation, Characterization and Evaluations of Carbon-Doped Ag/Fe/TiO₂ Mesoporous Nanocomposite Photocatalyst for Degradation of Methylene Blue and Congo Red

Carbon doped silver/iron/TiO₂ nanocomposite is synthesized via the solvothermal technique. Titanium tetraisopropoxide is used as a TiO₂ source. The composite samples are characterized by different physicochemical methods, including nitrogen adsorption-desorption analysis, transmission electron microscope, scanning electron microscope, X-ray diffraction, photoluminescence, UV-vis, Fourier-transform infrared, and Energy dispersive X-ray spectroscopy. The nanocrystalline structure of the samples with anatase phase having a tetragonal shape is shown by the XRD and TEM analysis. The photo-absorption boundary of pure TiO₂ expands into the visible light region due to composite formation, shown by analysis of UV-vis data. An increase in the degree of electron-hole couple segregation is shown via photoluminescence analysis. N₂ adsorption-desorption analysis manifests the higher surface area of samples along with mesoporous nature. The high photodegradation action is shown by the composite samples as compared to pure mesoporous TiO₂.

Impact of Al doping on a hydrothermally synthesized β-Ga2O3 nanostructure for photocatalysis applications

Aluminum (Al)-doped beta-phase gallium oxide (β-Ga₂O₃) nanostructures with different Al concentrations (0 to 3.2 at%) are synthesized using a hydrothermal method. The single phase of the β-Ga₂O₃ is maintained without intermediate phases up to Al 3.2 at% doping. As the Al concentration in the β-Ga₂O₃ nanostructures increases, the optical bandgap of the β-Ga₂O₃ increases from 4.69 (Al 0%) to 4.8 (Al 3.2%). The physical, chemical, and optical properties of the Al-doped β-Ga₂O₃ nanostructures are correlated with photocatalytic activity via the degradation of a methylene blue solution under ultraviolet light (254 nm) irradiation. The photocatalytic activity is enhanced by doping a small amount of substitutional Al atoms (0.6 at%) that presumably create shallow level traps in the band gap. These shallow traps retard the recombination process by separating photogenerated electron–hole pairs. On the other hand, once the Al concentration in the Ga₂O₃ exceeds 0.6 at%, the crystallographic disorder, oxygen vacancy, and grain boundary-related defects increase as the Al concentration increases. These defect-related energy levels are broadly distributed within the bandgap, which act as carrier recombination centers and thereby degrade the photocatalytic activity. The results of this work provide new opportunities for the synthesis of highly effective β-Ga₂O₃-based photocatalysts that can generate hydrogen gas and remove harmful volatile organic compounds.

The photocatalytic activity is correlated with different parameters affecting the photocatalytic reactions; redox potential (RP), surface area (SA), crystal defect (CD), oxygen defect (OD), and grain-boundary induced defect (GD).

Preferentially oriented Ag-TiO2 nanotube array film: An efficient visible-light-driven photocatalyst

Ag-TiO₂ nanotube array films with the preferential orientation of crystals were fabricated on ITO glass by magnetron sputtering and anodization. Comprehensive characterization was performed to ascertain the composition and microstructure characteristics of thin films. The photocatalytic activities were evaluated through the reduction of hexavalent chromium (Cr₂O₇^2- (Cr (VI)) as a model compound under visible light irradiation. XRD and XPS studies reveal the development of preferred orientation along [001] in anatase TiO₂ nanotubes by adjusting the Ag content during magnetron sputtering. Such unusual behavior is attributed to the minimization of anatase (001) surface energy assisted by Ag. The Ag-TiO₂ nanotube arrays having preferred crystal orientation exhibit superior separation/transfer of photo-induced charges. Furthermore, the Ag-TiO₂ nanotube arrays show improved absorption of visible light due to the SPR effect induced by Ag and the formation of heterojunction between the TNAs and Ag₂O. TNA-3Ag exhibits the highest photocatalytic activities by removing 99.1 % Cr (VI) in 90 min under visible light illumination.

Solvothermal synthesis of C doped Co-Cu/TiO2 based nanocomposite to study their photocatalytic activity

The solvothermal approach is applied to produce doped titanium dioxide nanoparticles in the mesoporous form using Pluronic F127 as a delicate mold. The formulated samples are investigated successfully via x-ray diffraction, ultraviolet-visible spectroscopy, photoluminescence spectroscopy, scanning electron microscope, energy dispersive x-ray, transmission electron microscope, nitrogen adsorption-desorption analysis, and Fourier-transform infrared spectroscopy. Analysis of XRD, SEM, and TEM demonstrates the existence of a nanocrystalline size range of the particles. Methylene blue, congo red, and malachite green dyes are used to evaluate the photocatalytic competence of the samples. The results verified that the TiO2 including a peak quantity of copper (4%) shows maximum photocatalysis caused by the declined bandgap energy including effective charge separation of photoinduced charge carrier with a maximum surface area as revealed by ultraviolet-visible, photoluminescence spectroscopy & nitrogen adsorption-desorption analysis respectively.

TiO2 nanofibres decorated with green-synthesized PAu/Ag@CQDs for the efficient photocatalytic degradation of organic dyes and pharmaceutical drugs

Organic pollutants such as dyes and pharmaceutical drugs have become an environmental menace, particularly in water bodies owing to their unregulated discharge. It is thus required to develop an economically viable and environment-friendly approach for their degradation in water bodies. In this study, for the first time, we report green route-synthesized plasmonic nanostructures (PM-CQDs (where M: Au and Ag)) decorated onto TiO2 nanofibers for the treatment of toxic dye- and pharmaceutical drug-based wastewater. PM-CQDs are efficaciously synthesized using carbon quantum dots (CQDs) as the sole reducing and capping agent, wherein CQDs are derived via a green synthesis approach from Citrus limetta waste. The characteristic electron-donating property of CQDs played a key role in the reduction of Au3+ to Au0 and Ag+ to Ag0 under visible light irradiation to obtain PAu-CQDs and PAg-CQDs, respectively. Thus, the obtained CQDs, PAu-CQDs, and PAg-CQDs are loaded onto TiO2 nanofibers to obtain a PM-CQD/TiO2 nanocomposite (NC), and are further probed via transmission electron microscopy, scanning electron microscopy and UV-visible spectrophotometry. The degradation of organic pollutants and pharmaceutical drugs using methylene blue and erythromycin as model pollutants is mapped with UV-vis and NMR spectroscopy. The results demonstrate the complete MB dye degradation in 20 minutes with 1 mg mL-1 of PAu-CQD/TiO2 NC, which otherwise is 30 minutes for PAg@CQD/TiO2 dose under visible light irradiation. Similarly, the pharmaceutical drug was found to degrade in 150 minutes with PAu-CQD/TiO2 photocatalysts. These findings reveal the enhanced photocatalytic performance of the green-synthesized Au decorated with TiO2 nanofibers and are attributed to the boosted SPR effect and aqueous-phase stability of Au nanostructures. This study opens a new domain of utilizing waste-derived and green-synthesized plasmonic nanostructures for the degradation of toxic/hazardous dyes and pharmaceutical pollutants in water.

Effects of different exchanging ions on the band structure and photocatalytic activity of defect pyrochlore oxide: a case study on KNbTeO6

The effects of different exchanging ions including Ag, Cu, and Sn on enhancing the photocatalytic activity of KNbTeO₆ are investigated by means of experiments and calculations.

Novel magnetic Fe3O4@rGO@ZnO onion-like microspheres decorated with Ag nanoparticles for the efficient photocatalytic oxidation of metformin: toxicity evaluation and insights into the mechanisms

Emerging water contaminants, including pharmaceutical and personal care products, have become a major concern in water pollution, and several efforts have been made for the efficient removal of these contaminants.

Solar Concentration for Wastewaters Remediation: A Review of Materials and Technologies

As the effectiveness of conventional wastewater treatment processes is increasingly challenged by the growth of industrial activities, a demand for low-cost and low-impact treatments is emerging. A possible solution is represented by systems coupling solar concentration technology with advanced oxidation processes (AOP). In this paper, a review of solar concentration technologies for wastewater remediation is presented, with a focus on photocatalyst materials used in this specific research context. Recent results, though mostly on model systems, open promising perspectives for the use of concentrated sunlight as the energy source powering AOPs. We identify (i) the development of photocatalyst materials capable of efficiently working with sunlight, and (ii) the transition to real wastewater investigation as the most critical issues to be addressed by research in the field.

Roles of Vanadium and Nitrogen in Photocatalytic Activity of VN-Codoped TiO2 Photocatalyst

In the present manuscript, we explore the VN-codoped TiO₂ system intended to understand the role played by each dopant in synergistic enhancement in performance of TiO₂ photocatalyst. The photocatalytic decomposition of organic pollutants in aqueous solution under visible light was used as a probe reaction to evaluate the performance of VN-codoped TiO₂ samples with different V and N concentrations. An optical measurement of VN-codoped TiO₂ shows considerable improved visible light absorption with increase in V-concentration as compared to increase in N concentration, which was due to the effective narrowing of the band gap by V-doping. The energy levels formed by N-dopants act as the trapping centers for photogenerated holes to suppress recombination process as indicated by PL and TRPL results. It is also observed that at high V-concentrations recombination centers are created in the form of oxygen vacancies as indicated by XPS and PL. In VN-codoped TiO₂ , addition of N partially fills these oxygen vacancies to reduce the number of recombination centers and prolong the lifetime of charge carriers. Thus, V improves the visible light absorption while N reduces the recombination of electron-hole pairs, thus creating the synergistic effect to produce three times better performance than pure TiO₂ .

Heterojunction ZnWO4/ZnFe2O4 composites with concerted effects and integrated properties for enhanced photocatalytic hydrogen evolution

A novel co-catalyst free ZnWO₄/ZnFe₂O₄ heterojunction composite was successfully synthesized using a facile co-precipitation method for photocatalytic H₂ evolution.