Photovoltaic-enhanced water splitting properties of low-temperature-synthesized BiVO4 photoanode films

The fabrication of photoelectrodes on indium tin oxide (ITO) glass at low temperatures poses a significant challenge due to the inherent instability of ITO at reduced temperatures, while the inexpensive production of high-functionality photoanode technology is a critical determinant facilitating large-scale photovoltaic conversion in water splitting. In this work, highly efficient BiVO4 (BVO) photoanodes with different thicknesses were grown on ITO glass at a low temperature by the sol-gel spin coating method. Pure BVO photoanode, enriched with nanostructures, exhibits a current density of 2.25 mA cm-2 (@1.23 V vs. RHE) under AM-1.5G illumination. The photovoltaic effect induces a continual oxygen evolution reaction at zero bias voltage on the photoanode, resulting in a photocurrent density of 0.04 mA cm-2 at zero bias. This study not only evaluates the feasibility of the large-scale fabrication of a photoanode from economic considerations but also presents potential for water splitting properties of the BVO photoanode.

Interface-engineered Z-scheme of BiVO4/g-C3N4 photoanode for boosted photoelectrochemical water splitting and organic contaminant elimination under solar light

Although n-type bismuth vanadate (BiVO₄) is regarded as an attractive solar-light-active photoanode, its short carrier-diffusion length, sluggish oxidation kinetics, low electronic conductivity, and high recombination rate are the major intrinsic shortcomings that limit its practical application. To this end, the rational design of a solar-light-active, metal-free BiVO₄-based Z-scheme heterojunction photoanode is of great significance for achieving effective charge-separation features and maximum light utilization as well as boosting redox activity for efficient environmental treatment and photoelectrochemical water splitting. Herein, we propose a facile approach for the decoration of metal-free graphitic carbon nitride (g-C₃N₄) nanosheets on BiVO₄ to form a Z-scheme BiVO₄/g-C₃N₄ photoanode with boosted photoelectrochemical (PEC) water splitting and rapid photoelectrocatalytic degradation of methyl orange (MO) dye under simulated solar light. The successful preparation of the Z-scheme BiVO₄/g-C₃N₄ photoanode was confirmed by comprehensive structural, morphological, and optical analyses. Compared with the moderate photocurrent density of bare BiVO₄ (0.39 mA cm^-2), the Z-scheme BiVO₄/g-C₃N₄ photoanode yields a notable photocurrent density of 1.14 mA cm^-2 at 1.23 V vs. RHE (≈3-fold higher) with the promising long-term stability of 5 h without any significant photo-corrosion. Moreover, the PEC dye-degradation studies revealed that the Z-scheme BiVO₄/g-C₃N₄ photoanode successfully degraded MO (≈90%) in 75 min, signifying a 30% improvement over bare BiVO₄. This research paves the way for rational interface engineering of solar-light-active BiVO₄-based noble-metal-free Z-schemes for eco-friendly PEC water splitting and water remediation.

Multi-Function of the Ni Interlayer in the Design of a BiVO4-Based Photoanode for Photoelectrochemical Water Splitting

BiVO₄ with an appropriate band structure is considered to be an ideal candidate for photoanodes. However, slow water oxidation kinetics and low charge separation efficiency seriously restrict its application. To address these issues, an NF/N/BVO photoanode with a hierarchical network structure was successfully constructed by direct-current magnetron sputtering of Ni followed by electrochemical deposition of nickel-iron layered double hydroxide (NiFe-LDH) on BiVO₄. A photocurrent density of 4.50 mA/cm² was obtained for NF/N/BVO, which was 2.4 times that for pristine BiVO₄. The introduction of the Ni layer contributed to the following growth of NiFe-LDH nanosheets with larger size, which acted as active sites and speeded up water oxidation kinetics. Furthermore, surface photovoltage microscopy revealed that Ni and NiFe-LDH acted as the electron collector and hole reservoir, respectively. The co-existence of the two components constituted a highly efficient surface charge separation structure, which was one of the important issues for the excellent water oxidation activity.

Photoconversion efficiency of In2S3/ZnO core-shell heterostructures nanorod arrays deposited via controlled SILAR cycles

This paper reports the structures, morphologies, optical properties, and photoconversion efficiency (η%) of the In2S3/ZnO core-shell heterostructures nanorod arrays (IZCSHNRAs) produced via the controlled successive ionic layer absorption and reaction (SILAR) cycles. As-produced samples were characterized using XRD, FESEM, TEM, UV-Vis, PL, XPS and FTIR techniques. The proposed IZCSHNRAs revealed nearly double photocurrent density and η% values compared to the pure ZnO nanorod arrays (ZNRAs). In addition, the light absorption, crystallinity and microstructures of the specimens were appreciably improved with the increase of the SILAR cycles. The deposited nanoparticles of In2S3 (ISNPs) on the ZNRAs surface was responsible for the improvement in the heterostructures, light absorption and photogenerated electron-hole pairs separation, thus enhancing the photoconversion performance. It is established that a simple SILAR approach can be very useful to produce good quality IZCSHNRAs-based photoelectrodes required for the future development of high performance photoelectrochemical cells (PECs).

SILAR Deposition of Metal Oxide Nanostructured Films

Methods for the fabrication of thin films with well controlled structure and properties are of great importance for the development of functional devices for a large range of applications. SILAR, the acronym for Successive Ionic Layer Adsorption and Reaction, is an evolution and combination of two other deposition methods, the Atomic Layer Deposition and Chemical Bath Deposition. Due to a relative simplicity and low cost, this method has gained increasing interest in the scientific community. There are, however, several aspects related to the influence of the many parameters involved, which deserve further deepening. In this review article, the basis of the method, its application to the fabrication of thin films, the importance of experimental parameters, and some recent advances in the application of oxide films are reviewed. At first the fundamental theoretical bases and experimental concepts of SILAR are discussed. Then, the fabrication of chalcogenides and metal oxides is reviewed, with special emphasis to metal oxides, trying to extract general information on the effect of experimental parameters on structural, morphological and functional properties. Finally, recent advances in the application of oxide films prepared by SILAR are described, focusing on supercapacitors, transparent electrodes, solar cells, and photoelectrochemical devices.

rGO decorated ZnO/CdO heterojunction as a photoanode for photoelectrochemical water splitting

A ternary photoanode of ZnO/CdO heterojunction decorated with reduced graphene oxide (rGO) was firstly fabricated by electrochemical deposition and thermal decomposition that is simple and effective compared with other method reported in literature. The structure and morphology of the photoanode were systematically characterized by various spectrum technologies. The photoanode expands the visible light absorption range to 428 nm, the photocurrent density reaches 1.15 mA·cm^-2 at 1.23 V (vs. RHE) that is 3 times and 1.85 times of pure ZnO (0.38 mA·cm²) and ZnO/CdO (0.62 mA·cm²) photoanodes. The highest IPCE value reaches 42.63% at 380 nm. The enhancement is attributed to the architecture of semiconductor heterojunctions and the decoration of rGO nanosheets, the former promotes charge separation, while the latter accelerates electron transfer thus both synergistically enhance PEC water splitting efficiency. Here fabricated photoanode has never been reported before, only Cd and other metal elements doped ZnO photoanodes were reported in the literature.

Microbial fuel cells for remediation of environmental pollutants and value addition: Special focus on coupling diatom microbial fuel cells with photocatalytic and photoelectric fuel cells

With the advent of global industrialisation and adaptation of smart life there is rise in anthropogenic pollution especially in water. Remediation of the pollutants (such as metals, and dyes) present in industrial effluents is possible via microbes and algae present in the environment. Microbes are used in a microbial fuel cell (MFC) for remediation of various organic and inorganic pollutants. However, for industrial scale application coupling the MFCs with photocatalytic and photoelectric fuel cell has a potential in improving the output of power. It can also be used for remediation of pollutants more expeditiously, conserving fossil fuels, cleaning environment, hence making the coupled hybrid fuel cell to run economically. Furthermore, such MFC inbuilt with algae in living or powder form give additional value addition products like biofuel, polysaccharides, biopolymers, and polyhydroxy alkanoates etc. This review provides bird's eye view on the removal of environmental pollutants by different biological sources like bacteria and algae. The article is focussed on diatoms as potential algae since they are rich source of crude oil and high value added products in a hybrid photocatalytic MFC. It also covers bottle necks, challenges and future in this field of research.

Synthesis and control strategies of nanomaterials for photoelectrochemical water splitting

Photoelectrochemical water splitting to produce hydrogen using solar energy can capture and directly convert solar energy into chemical energy, which is an effective way to deal with the current energy and environmental problems. The conversion efficiency of solar energy depends on the performance of semiconductor photoelectrodes in photoelectrochemical water splitting. This article presents our recent advances in the design and performance control of high-efficiency photoelectrocatalytic materials, followed by the discussion of the strategies employed for improving the performances of photoelectrodes in terms of photon absorption, charge separation and migration, as well as surface chemical reactions.

Rationally embedded zinc oxide nanospheres serving as electron transport channels in bismuth vanadate/zinc oxide heterostructures for improved photoelectrochemical efficiency

In this work, we demonstrate the fabrication of Mo, W co-doped BiVO₄/ZnO nanosphere (Mo, W: BVO/ZnO NS) heterostructures using a simple solution dry-out method that uniformly embeds ZnO NSs in Mo, W: BVO nanocrystals. Photoelectrochemical (PEC) examination confirmed that Mo, W: BVO/ZnO NSs exhibit higher PEC performance than pure Mo, W: BVO, and this improved performance of Mo, W: BVO/ZnO NSs also depends on decreased ZnO NS size. Moreover, a layered ZnO/Mo, W: BVO (ZnO film coated with Mo, W: BVO layer) heterostructure was prepared using a simple physical piled method that exhibited far lower PEC performances than those of Mo, W: BVO/ZnO NS heterostructures. These results clearly revealed that the formation of the Mo, W: BVO/ZnO NS heterostructure could increase the charge carrier density and it possessed a much larger contact area. These improvements were favorable for the transfer and transport of photoexcited charge carriers. This work offers an effective strategy to fabricate heterostructures with effective charge separation by a simple solution dry-out method that is suitable for other heterostructure-engineered photoanodes in solar water-splitting applications.

Enhanced photoelectrochemical performance of NaNbO3 nanofiber photoanodes coupled with visible light active g-C3N4 nanosheets for water splitting

Sodium niobate nanofibers (NaNbO₃-NF) have been synthesized using a hydrothermal technique and further coupled with visible light responsive graphitic carbon nitride (g-C₃N₄) nanosheets in different concentration ratios of 2:1 (2-CN), 4:1 (4-CN) and 8:1 (8-CN). A significant improvement in the photoelectrochemical (PEC) performance of the g-C₃N₄/NaNbO₃-NF (4-CN) nanostructured photoanode compared to the bare NaNbO₃ photoanode is observed. A current density of 12.55 mA cm^-2 at 1 V with respect to the Ag/AgCl reference electrode is achieved for the g-C₃N₄/NaNbO₃-NF (4-CN) photoanode, which is ∼3 times higher than the NaNbO₃-NF photoanode. Also, compared to NaNbO₃-NF, the g-C₃N₄/NaNbO₃-NF (4-CN) nanocomposite photoanode showed ∼3 times improvement in the incident photon-to-current conversion efficiency. The improvement in the PEC performance of visible light active g-C₃N₄/NaNbO₃-NF (4-CN) nanocomposite is attributed to the improved photoresponse of NaNbO₃-NF due to the coupling of g-C₃N₄ and the formation of a type-II heterojunction between them leading to the enhanced separation of the photogenerated charge carriers. A possible reaction mechanism for the improved PEC water splitting performance has been proposed for the g-C₃N₄/NaNbO₃-NF (4-CN) photoanode.

Layered Double Hydroxide onto Perovskite Oxide-Decorated ZnO Nanorods for Modulation of Carrier Transfer Behavior in Photoelectrochemical Water Oxidation

Despite the fact that perovskite oxides with high photoelectrochemical (PEC) stability have gained widespread concern in the field of photo(electro)catalytic water splitting, the potential as a photoelectrode has not yet fully exploited. Herein, perovskite oxide-decorated ZnO nanorod photoanode improves the vital issue that photoproduced electron-hole pairs are apt to be quenched, in which type II band alignment between perovskite oxide and ZnO plays a crucial role in extracting carriers. Further, coupling with layered double hydroxide (LDH) onto the heterostructure not only tunes surface injection behavior of charge carriers by facilitating the interface reaction dynamics but also suppresses ZnO self-corrosion for extended durability. As a result, the optimized CoAl-LDH/LaFeO₃/ZnO nanorod photoanode yields a much enhancive effect for the PEC property in terms of photocurrent density (2.46 mA cm^-2 at 1.23 V vs reversible hydrogen electrode under AM 1.5G), onset potential, and stability. This work signifies a feasible design to combine promising perovskite oxides with the traditional photoelectrode system for achieving efficient water splitting.

Multi-dimensional zinc oxide (ZnO) nanoarchitectures as efficient photocatalysts: What is the fundamental factor that determines photoactivity in ZnO?

While bulk zinc oxide (ZnO) is of non-toxic in nature, ZnO nanoarchitectures could potentially induce the macroscopic characteristics of oxidative, lethality and toxicity in the water environment. Here we report a systematic study through state-of-the-art controllable synthesis of multi-dimensional ZnO nanoarchitectures (i.e. 0D-nanoparticle, 1D-nanorod, 2D-nanosheet, and 3D-nanoflowers), and subsequent in-depth understanding on the fundamental factor that determines their photoactivities. The photoactivities of resultant ZnO nanoarchitectures were interpreted in terms of the photodegradation of salicylic acid as well as inactivation of Bacillus subtilis and Escherichia coli under UV-A irradiation. Photodegradation results showed that 1D-ZnO nanorods demonstrated the highest salicylic acid photodegradation efficiency (99.4%) with a rate constant of 0.0364 min^-1. 1D-ZnO nanorods also exhibited the highest log reductions of B. subtilis and E. coli of 3.5 and 4.2, respectively. Through physicochemical properties standardisation, an intermittent higher k value for pore diameter (0.00097 min^-1 per mm), the highest k values for crystallite size (0.00171 min^-1 per nm) and specific surface area (0.00339 min^-1 per m²/g) contributed to the exceptional photodegradation performance of nanorods. Whereas, the average normalised log reduction against the physicochemical properties of nanorods (i.e. low crystallite size, high specific surface area and pore diameter) caused the strongest bactericidal effect.

Nanoporous BiVO4 nanoflake array photoanode for efficient photoelectrochemical water splitting

A high-quality nanoporous BiVO₄ nanoflake array photoanode was prepared by using an in situ transformation approach, which exhibited an excellent photoelectrochemical activity.

Current progress in developing metal oxide nanoarrays-based photoanodes for photoelectrochemical water splitting

Solar energy driven photoelectrochemical (PEC) water splitting is a clean and powerful approach for renewable hydrogen production. The design and construction of metal oxide based nanoarray photoanodes is one of the promising strategies to make the continuous breakthroughs in solar to hydrogen conversion efficiency of PEC cells owing to their owned several advantages including enhanced reactive surface at the electrode/electrolyte interface, improved light absorption capability, increased charge separation efficiency and direct electron transport pathways. In this Review, we first introduce the structure, work principle and their relevant efficiency calculations of a PEC cell. We then give a summary of the state-of the-art research in the preparation strategies and growth mechanism for the metal oxide based nanoarrays, and some details about the performances of metal oxide based nanoarray photoanodes for PEC water splitting. Finally, we discuss key aspects which should be addressed in continued work on realizing high-efficiency metal oxide based nanoarray photoanodes for PEC solar water splitting systems.

Fe2TiO5 as an Efficient Co-catalyst To Improve the Photoelectrochemical Water Splitting Performance of BiVO4

Fe₂TiO₅ was synthesized via the solvothermal method and adopted as co-catalyst to improve the photoelectrochemical (PEC) water splitting performance of BiVO₄ photoanode. After surface modification by Fe₂TiO₅, the BiVO₄/Fe₂TiO₅ photoanode shows a 300 mV cathodic shift in onset potential and 3 times enhancement in photocurrent, which delivers a photocurrent density of 3.2 mA/cm² at 1.23 V vs reverse hydrogen electrode. Systematic optical, electrochemical, and intensity-modulated photocurrent spectroscopy characterizations were performed to explore the role of Fe₂TiO₅ and reveal that the enhanced PEC performance is mainly caused by the surface passivation effect of Fe₂TiO₅.

Three-Dimensional Bicontinuous BiVO4/ZnO Photoanodes for High Solar Water-Splitting Performance at Low Bias Potential

A photoanode capable of high-efficiency water oxidation at low bias potential is essential for its practical application for photocathode-coupled tandem systems. To address this issue, a photoanode with low turn-on voltage for water oxidation and high charge separation efficiency at low bias potential is essential. In this study, we demonstrate the photoanode of the BiVO₄/ZnO three-dimensional (3D) bicontinuous (BC) structure. ZnO has a relatively cathodic flat-band potential, which leads to low turn-on potential; the BiVO₄/ZnO 3D BC photoanode shows an onset potential of 0.09 V versus the reversible hydrogen electrode ( V_RHE). Moreover, we achieve remarkably high charge separation efficiency at low bias potential (78% at 0.6 V_RHE); this is attributed to the application of thin-film BiVO₄ shells by high light-scattering properties of the 3D BC structure. As a result, the BiVO₄/ZnO 3D BC photoanode generates a high water oxidation photocurrent of up to 3.4 ± 0.2 mA cm^-2 (with CoPi catalyst coating). This photocurrent value is reproducible, and the photocurrent-to-O₂ conversion efficiency is over 90%. To the best of our knowledge, this is the highest value among the values of the photocurrent at 0.6 V_RHE in previous BiVO₄-based heterojunction photoanodes.

Effects of Anions and pH on the Stability of ZnO Nanorods for Photoelectrochemical Water Splitting

This work demonstrates the improved stability of zinc oxide nanorods (ZnO NRs) for the photoanode of solar water splitting under voltage biases by the addition of borate or carbonate ions in the aqueous electrolyte with suitable pH ranges. The ZnO NRs prepared by the hydrothermal method are highly active and stable at pH 10.5 in both borate and carbonate buffer solutions, where a photocurrent higher than 99% of the initial value has been preserved after 1 h polarization at 1.5 V (vs reversible hydrogen electrode) under AM 1.5G. The optimal pH ranges with a minimum morphological change of ZnO NRs for photoelectrochemical (PEC) water splitting in borate and carbonate buffer solutions are 9-13 and 10-12, respectively. The working pH range for PEC water splitting on ZnO NR photoanodes can be extended to 8.5-12.5 by the combination of borate and carbonate anions. The lifetime of ZnO NR photoanodes can be synergistically prolonged for over an order of magnitude when the electrolyte is the binary electrolyte consisting of borate and carbonate in comparison with these two anions used individually. On the basis of the experimental results, a possible mechanism for the protective behavior of ZnO in borate and carbonate solutions is proposed. These findings can be used to improve the lifetime of other high-performance ZnO-based catalysts and to understand the photocorrosive and protective behaviors of ZnO NRs in the borate and carbonate solutions.

Advanced bi-functional CoPi co-catalyst-decorated g-C3N4 nanosheets coupled with ZnO nanorod arrays as integrated photoanodes

In this work, a CoPi-decorated type II heterojunction composed of one-dimensional (1D) ZnO nanorod arrays (NRAs) coated with two-dimensional (2D) carbon nitride (g-C₃N₄) was successfully prepared and used as photoanode.

Highly efficient BiVO4 single-crystal photocatalyst with selective Ag2O-Ag modification: orientation transport, rapid interfacial transfer and catalytic reaction

Highly efficient Ag₂O-Ag/BiVO₄ single-crystal photocatalyst: (1) orientation transport, (2) rapid interfacial transfer and (3) catalytic reaction.

Plasmonic gold nanoparticle-decorated BiVO4/ZnO nanowire heterostructure photoanodes for efficient water oxidation

To enhance the charge separation and kinetics of water oxidation using a BiVO₄ photoanode, a BiVO₄/ZnO nanowire heterostructure decorated with gold (Au) nanoparticles is fabricated as a photoanode for photoelectrochemical water splitting.

Nanostructured shuriken-like BiVO4 with preferentially exposed {010} facets: preparation, formation mechanism, and enhanced photocatalytic performance

The synthesis, formation mechanism, and application of nanostructured shuriken-like BiVO₄ with preferentially exposed {010} facets have been reported.

Recent Advances in Bismuth-Based Nanomaterials for Photoelectrochemical Water Splitting

In recent years, bismuth-based nanomaterials have drawn considerable interest as potential candidates for photoelectrochemical (PEC) water splitting owing to their narrow band gaps, nontoxicity, and low costs. The unique electronic structure of bismuth-based materials with a well-dispersed valence band comprising Bi 6s and O 2p orbitals offers a suitable band gap to harvest visible light. This Review presents significant advancements in exploiting bismuth-based nanomaterials for solar water splitting. An overview of the different strategies employed and the new ideas adopted to improve the PEC performance of bismuth-based nanomaterials are discussed. Morphology control, the construction of heterojunctions, doping, and co-catalyst loading are several approaches that are implemented to improve the efficiency of solar water splitting. Key issues are identified and guidelines are suggested to rationalize the design of efficient bismuth-based materials for sunlight-driven water splitting.