Intriguing and Facile Preparation Approach of CdO Nanorod-Based Abundant Chitosan for Symmetric Supercapacitors

Abundant chitosan was rationally used for the green fabrication of cadmium oxide nanorods (CdO nanorods) owing to its environmentally benign characteristics, bioavailability, low cost, etc. However, the primary unsubstituted amino group of chitosan interacts with the surface of Cd salt at higher temperatures, resulting in CdO nanorod formation. A one-step hydrothermal technique was adopted in the presence of chitosan. Optical, structural, and morphology techniques characterized CdO nanorods. According to X-ray diffraction crystallography, CdO is well crystallized in the face-centered cubic lattice with an Fm-3m (225) space group. The AC@CdO nanoelectrode demonstrated an outstanding gravimetric capacitance of 320 F g-1 at a current density of 0.5 A g-1, nearly three-fold that of ordinary AC electrodes. The AC electrode and the AC@CdO nanoelectrode retain 90 and 93% of their initial specific capacitance after 10,000 galvanostatic charge discharge cycles. The AC@CdO nanoelectrode has a lower equivalent series resistance value than the AC electrode. Moreover, AC@CdO symmetric supercapacitor devices achieve excellent results in terms of specific energy, specific power, and capacitance retention.

An enzyme free simultaneous detection of γ-amino-butyric acid and testosterone based on copper oxide nanoparticles

Herein, an easy wet-chemical process was used in basic medium with low temperature to prepare low-dimensional copper oxide nanoparticles (CuO NPs). A variety of optical and structural techniques such as UV-visible, FT-IR, XRD, FESEM, XEDS, and XPS were used to characterize the synthesized CuO NPs in detail. Two sensitive and selective sensor probes for γ-amino-butyric acid (GABA) and testosterone (TST) were achieved after modification; a thin layer of NPs on a flat glassy carbon electrode (GCE). Sensor analytical parameters such as sensitivity (SNT), linear dynamic range (LDR), limit of detection (LOD), limit of quantification (LOQ), robustness, and interference effects, were evaluated for the proposed sensor (GCE/CuO NPs) for GABA and TST, based on a dependable current-voltage technique. Calibration curves were found to be linear (R ² = 0.9963 and 0.9095) over a broad concentration range of GABA and TST (100.0 pM to 100.0 mM and 10.0 pM to 10.0 mM, respectively). Sensor parameters - SNT (316.46 and 2848.10 pA μM^-1 cm^-2), LDR (100.0 nM to 10.0 mM and 10.0 pM to 1.0 mM), LOD (≈11.70 and 96.67 pM), and LOQ (39.0 and 322.2 pM) - for GABA and TST were calculated from the calibration plot successively. Preparation of CuO NPs using the wet-chemical technique is a good approach for perspective expansion of NPs-based sensors for the enzyme-free detection of biomolecules. Our sensor probe (GCE/CuO NPs) is applied for the cautious recognition of GABA and TST in real biological samples -human, mouse, and rabbit serum - and achieved good and acceptable results.

Optical, Structural and Photoluminescence Properties of Gd x SrO: CdO Nanostructures Synthesized by Co Precipitation Method

To investigate the effect of Gd _x SrO: CdO (x = 0.1, 0.3, 0.4) nanostructures (NS), in the present work an attempt has been made to synthesize Gd_x SrO:CdO NS by co precipitation method. Structural properties were investigated by XRD (X-ray diffraction), FTIR (Fourier transform infrared spectroscopy), SEM (scanning electron microscopy), UV-Visible, XPS (X-ray photoelectron spectroscopy). XRD indicates having mixed phase of tetragonal crystal structure and SEM images indicate spherical shaped nanoparticles (NPs) of Gd _x SrO:CdO with average size laying in between ~100 nm to ~130 nm. FTIR spectra of Gd _x SrO: CdO NS show stretching and bending peaks of Gd-O-Gd, Cd-O-Cd and Sr-OH at ~1311 cm ^-1, ~1486 cm ^-1, ~ 3300 cm ^-1 and UV-visible optical absorptivity of Gd _x SrO:CdO show absorption maxima shift from 330 nm to 324 nm (blue shift) and edges at 352.4 nm, 348 nm and 346.3 nm respectively for Gd concentration varying between 0.1, 0.3 and 0.4. binding energies of the Gd 3d _3/2, Sr 3d _3/2 and Cd 3d _3/2, O1s and C1s observed at 150.8 eV, 141.6 eV, 410.1 eV, 529.6 eV and 282.4 eV respectively which confirms the chemical composition of NS. Photoluminescence (PL) spectrum of Gd _0.4 Sr _0.5 O Cd _0.1O NS exhibit broad peaks from 338 nm to 397 nm centred around 369 nm with various Gd, O, Sr and Cd related native defects. Emission band observed at UV- Visible region for Gd _0.3 Sr _0.5 O Cd _0.2 O NS PL emission spectra has two emission peaks at 369 nm (UV region) and 550 nm (Visible region). The transitions can be ascertained with shielding of 4f shells of Gd⁺³ ions by 6 s, 5d shells by the interaction of the other Gd⁺³ ions.

An Electrochemical Approach for the Selective Detection of Cancer Metabolic Creatine Biomarker with Porous Nano-Formulated CMNO Materials Decorated Glassy Carbon Electrode

The facile wet-chemical technique was used to prepare the low-dimensional nano-formulated porous mixed metal oxide nanomaterials (CuO.Mn2O3.NiO; CMNO NMs) in an alkaline medium at low temperature. Detailed structural, morphological, crystalline, and functional characterization of CMNO NMs were performed by X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (XRD), ultraviolet-visible spectroscopy (UV-vis), Fourier-transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), and energy-dispersive X-ray spectroscopy (EDS) analyses. An efficient and selective creatine (CA) sensor probe was fabricated by using CMNO NMs decorated onto glassy carbon electrode (GCE) as CMNO NMs/GCE by using Nafion adhesive (5% suspension in ethanol). The relation of current versus the concentration of CA was plotted to draw a calibration curve of the CMNO NMs/GCE sensor probe, which was found to have a very linear value (r2 = 0.9995) over a large dynamic range (LDR: 0.1 nM~0.1 mM) for selective CA detection. The slope of LDR by considering the active surface area of GCE (0.0316 cm2) was applied to estimate the sensor sensitivity (14.6308 µAµM-1 cm-2). Moreover, the detection limit (21.63 ± 0.05 pM) of CMNO MNs modified GCE was calculated from the signal/noise (S/N) ratio at 3. As a CA sensor probe, it exhibited long-term stability, good reproducibility, and fast response time in the detection of CA by electrochemical approach. Therefore, this research technique is introduced as a promising platform to develop an efficient sensor probe for cancer metabolic biomarker by using nano-formulated mixed metal oxides for biochemical as well as biomedical research for the safety of health care fields.

The synthesis and application of (E)-N'-(benzo[d]dioxol-5-ylmethylene)-4-methyl-benzenesulfonohydrazide for the detection of carcinogenic lead

In this study, noble ligands of (E)-N'-(benzo[d]dioxol-5-ylmethylene)-4-methyl-benzenesulfonohydrazide (BDMMBSH) were prepared via a simple condensation method using benzo-[d][1,3]-dioxole carbaldehyde, benzenesulfonylhydrazine (BSH), and 4-methyl-benzenesulphonylhydrazine (4-MBSH) in good yield, which were crystallized in acetone, EtOAc, and EtOH. The BDMMBSH derivatives were characterized using different spectroscopic techniques, such as 1H-NMR, 13C-NMR, FTIR, and UV-Vis spectroscopy, and their crystal structures were analyzed using the single crystal X-ray diffraction method (SCXRDM). Subsequently, the BDMMBSH compounds were used for the significant detection of the carcinogenic heavy metal ion, lead (Pb2+), via a reliable electrochemical approach. A sensitive and selective Pb2+ sensor was developed via the deposition of a thin layer of BDMMBSH on a GCE with the conducting polymer matrix Nafion (NF). The sensitivity, LOQ, and LOD of the proposed sensor towards Pb2+ were calculated from the calibration curves to be 2220.0 pA μM-1 cm-2, 320.0 mM, and 96.0 pM, respectively. The validation of the BDMMBSH/GCE/NF sensor probe was performed via the selective determination of Pb2+ in spiked natural samples with a satisfactory and rational outcome.

A reliable alternative approach for the ultra-sensitive detection ofl-glutathione with wet chemically synthesized Co3O4-doped SnO2nanoparticles decorated on a glassy carbon electrode

An electrochemical sensor was developed for the non-enzymatic detection ofl-glutathione based on wet-chemically prepared Co₃O₄-doped SnO₂nanoparticles decorated on a glassy carbon electrode sensor-probe.

Enzyme-free detection of uric acid using hydrothermally prepared CuO·Fe2O3 nanocrystals

Copper oxide doped iron oxide nanocrystals (CuO·Fe₂O₃ NCs) were prepared using a simple hydrothermal technique at low temperature in an alkaline medium.

A non-enzymatic electrochemical approach for l-lactic acid sensor development based on CuO·MWCNT nanocomposites modified with a Nafion matrix

Copper oxide decorated multi-walled carbon nanotube nanocomposites (CuO·MWCNT NCs) were prepared using a simple wet-chemical technique in basic medium.

Simultaneous detection of l-aspartic acid and glycine using wet-chemically prepared Fe3O4@ZnO nanoparticles: real sample analysis

An easy and reliable wet-chemical method was used to synthesize iron oxide doped zinc oxide nanoparticles (Fe₃O₄@ZnO NPs) at a low-temperature under alkaline medium.

Arsenic sensor development based on modification with (E)-N′-(2-nitrobenzylidine)-benzenesulfonohydrazide: a real sample analysis

(E)-N′-(2-Nitrobenzylidene)-benzenesulfonohydrazide was prepared from 2-nitrobenzaldehyde and benzenesulfonylhydrazine by using a condensation method and applied as a selective As³⁺ sensor.

d-Glucose sensor based on ZnO·V2O5 NRs by an enzyme-free electrochemical approach

A simple wet-chemical technique was used to prepare zinc oxide-doped vanadium pentaoxide nanorods (ZnO·V₂O₅ NRs) in an alkaline environment. The synthesized ZnO·V₂O₅ NRs were characterized using typical methods, including UV-visible spectroscopy (UV-Vis), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), energy dispersive X-ray spectroscopy (XEDS), X-ray photoelectron spectroscopy (XPS), and X-ray powder diffraction (XRD). The d-glucose (d-GLC) sensor was fabricated with modification of a slight coating of nanorods (NRs) onto a flat glassy carbon electrode (GCE). The analytical performances, such as the sensitivity, limit of quantification (LOQ), limit of detection (LOD), linear dynamic range (LDR), and durability, of the proposed d-GLC sensor were acquired by a dependable current–voltage (I–V) process. A calibration curve of the GCE/ZnO·V₂O₅ NRs/Nf sensor was plotted at +1.0 V over a broad range of d-GLC concentrations (100.0 pM–100.0 mM) and found to be linear (R² = 0.6974). The sensitivity (1.27 × 10⁻³ μA μM⁻¹ cm⁻²), LOQ (417.5 mM), and LOD (125 250 μM) were calculated from the calibration curve. The LDR (1.0 μM–1000 μM) was derived from the calibration plot and was also found to be linear (R² = 0.9492). The preparation of ZnO·V₂O₅ NRs by a wet-chemical technique is a good advancement for the expansion of nanomaterial-based sensors to support enzyme-free sensing of biomolecules in healthcare fields. This fabricated GCE/ZnO·V₂O₅ NRs/Nf sensor was used for the recognition of d-glucose in real samples (apple juice, human serum, and urine) and returned satisfactory and rational outcomes.

A simple wet-chemical technique was used to prepare zinc oxide-doped vanadium pentaoxide nanorods (ZnO·V₂O₅ NRs) in an alkaline environment.

Fabrication of a Ga3+ sensor probe based on methoxybenzylidenebenzenesulfonohydrazide (MBBSH) by an electrochemical approach

A thin-layer of (E)-N′-methoxybenzylidenebenzenesulfonohydrazide (MBBSH) was fabricated by the deposition of MBBSH onto a smooth glassy carbon electrode with nafion binder for the sensitive and selective Ga³⁺ sensor probe.

A Ce2+ sensor based on napthalen-1-yl-methylene-benzenesulfonohydrazide (NMBSH) molecules: ecological sample analysis

A sensitive and selective Ce²⁺ sensor was developed based on napthalen-1-yl-methylene-benzenesulfonohydrazide (NMBSH) derivatives via an electrochemical approach.