Dynamic Deposition of PDA on a Hollow Fiber Ceramic Membrane for Oily Water Treatment

Ceramic membranes have been widely used in oil-water treatment; however, membrane fouling remains a challenge that must be addressed to improve the process feasibility. A thin layer of polydopamine (PDA) was dynamically deposited on the surface of the alumina hollow fiber membranes to reduce oil adhesion. The PDA-alumina membranes were characterized by using SEM-EDS, AFM, and water contact angle measurements. The performance of the modified membranes was evaluated using synthetic crude oil emulsions (100 mg·L-1) in a crossflow system. Membranes modified with PDA exhibited 97% oil rejection, and a stabilized permeate flux of 463 L·h-1·m-2 with a relative flux reduction of 60% and a flux recovery ratio of 75% was observed after cleaning, indicating lower oil adhesion and better fouling reversibility. The most predominant fouling mechanism for the modified membranes seems to be cake filtration because of the reduction in pore size due to the deposition of the PDA layer.

Effects of pollutants in alkali/surfactant/polymer (ASP) flooding oilfield wastewater on membrane fouling in direct contact membrane distillation by response surface methodology

The characteristic pollutants in alkali/surfactant/polymer (ASP) flooding oilfield wastewater are complex [e.g., NaCl, sodium dodecyl sulfate (SDS), petroleum, and polyacrylamide (PAM)]; thus, membrane distillation (MD) applied to treat this wastewater will be fouled and wetted easily. In this study, response surface methodology (RSM) was used to analyze the effects of pollutant interactions in ASP flooding oilfield wastewater on membrane fouling. The response model showed quantitative relationships between the membrane flux and the pollutant concentrations. The analysis of variance (p-value of the model < 0.0001, p-value of lack of fit > 0.05, R² = 0.9750 and R²_adj = 0.9500) showed that the regression equation fit the empirical data well. The results also indicated that the interactions of pollutants (NaCl and SDS; petroleum and PAM) had significant influence on the flux decline in the simulated ASP flooding oilfield wastewater. The characterization of Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) revealed that the MD membrane was fouled by simulated ASP flooding oilfield wastewater to a certain degree. Moreover, the membrane flux was restored to 86.9% after hydraulic cleaning.

Interception Characteristics and Pollution Mechanism of the Filter Medium in Polymer-Flooding Produced Water Filtration Process

Polymer flooding enhances oil recovery, but during the application of this technology, it also creates a large amount of polymer-contained produced water that poses a threat to the environment. The current processing is mainly focused on being able to meet the re-injection requirements. However, many processes face the challenges of purifying effect, facilities pollution, and economical justification in the field practice. In the present work, to fully understand the structure and principle of the oil field filter tank, and based on geometric similarity and similar flow, a set of self-designed filtration simulation devices is used to study the treatment of polymer-contained produced water in order to facilitate the satisfaction of the water injection requirements for medium- and low-permeability reservoirs. The results show that, due to the existence of polymers in oil field produced water, a stable colloidal system is formed on the surface of the filter medium, which reduces the adsorption of oil droplets and suspended solids by the filter medium. The existence of the polymers also increases the viscosity of water, promotes the emulsification of oil pollution, and increases the difficulty of filtration and separation. As filtration progresses, the adsorption of the polymers by the filter medium bed reaches saturation, and the polymers and oil pollution contents in the filtered water increase gradually. The concentration and particle size of the suspended solids eventually exceed the permissible standards for filtered water quality; this is mainly due to the unreasonable size of the particle in relation to the filter medium gradation and the competitive adsorption between the polymers and the suspended solids on the surface of the filter medium. The oil concentration of the filtered water also exceeds the allowable standards and results from the polymers replace the oil droplets in the pores and on the surfaces of the filter medium. Moreover, the suspended particles of the biomass, composed of dead bacteria, hyphae, and spores, have strong attachment and carrying ability with respect to oil droplets, which cause the suspended solids in the filtered water to exceed the permissible standards and oil droplets to be retained in the filtered effluent at the same time.

Membrane-based separation for oily wastewater: A practical perspective

The large volumes of oily wastewater generated by various industries, such as oil and gas, food and beverage, and metal processing, need to be de-oiled prior to being discharged into the environment. Compared to conventional technologies such as dissolved air flotation (DAF), coagulation or solvent extraction, membrane filtration can treat oily wastewater of a much broader compositional range and still ensure high oil removals. In the present review, various aspects related to the practical implementation of membranes for the treatment of oily wastewater are summarized. First, sources and composition of oily wastewater, regulations that stipulate the extent of treatment needed before discharge, and the conventional technologies that enable such treatment are appraised. Second, commercially available membranes, membrane modules, operation modes and hybrids are overviewed, and their economics are discussed. Third, challenges associated with membrane filtration are examined, along with means to quantify and mitigate membrane fouling. Finally, perspectives on state-of-the-art techniques to facilitate better monitoring and control of such systems are briefly discussed.

Surface modification of piperazine-based nanofiltration membranes with serinol for enhanced antifouling properties in polymer flooding produced water treatment

A facile membrane modification method with serinol to improve the membrane performance in the advanced treatment of polymer flooding produced water.