Synthesis of Xanthan Gum Anchored α-Fe2O3 Bionanocomposite Material for Remediation of Pb (II) Contaminated Aquatic System

Increases in community and industrial activities have led to disturbances of the environmental balance and the contamination of water systems through the introduction of organic and inorganic pollutants. Among the various inorganic pollutants, Pb (II) is one of the heavy metals possessing non-biodegradable and the most toxic characteristics towards human health and the environment. The present study is focussed on the synthesis of efficient and eco-friendly adsorbent material that can remove Pb (II) from wastewater. A green functional nanocomposite material based on the immobilization of α-Fe₂O₃ nanoparticles with xanthan gum (XG) biopolymer has been synthesized in this study to be applied as an adsorbent (XGFO) for sequestration of Pb (II). Spectroscopic techniques such as scanning electron microscopy with energy dispersive X-ray (SEM-EDX), Fourier transform infrared (FTIR), transmission electron microscopy (TEM), X-ray diffraction (XRD), ultraviolet visible (UV-Vis) and X-ray photoelectron spectroscopy (XPS) were adopted for characterizing the solid powder material. The synthesized material was found to be rich in key functional groups such as -COOH and -OH playing important roles in binding the adsorbate particles through ligand-to-metal charge transfer (LMCT). Based on the preliminary results, adsorption experiments were conducted, and the data obtained were applied to four different adsorption isotherm models, viz the Langmuir, Temkin, Freundlich and D-R models. Based on the high values of R² and low values of χ², the Langmuir isotherm model was found to be the best model for simulation of data for Pb (II) adsorption by XGFO. The value of maximum monolayer adsorption capacity (Q_m) was found to be 117.45 mg g^-1 at 303 K, 126.23 mg g^-1 at 313 K, 145.12 mg g^-1 at 323 K and 191.27 mg g^-1 at 323 K. The kinetics of the adsorption process of Pb (II) by XGFO was best defined by the pseudo-second-order model. The thermodynamic aspect of the reaction suggested that the reaction is endothermic and spontaneous. The outcomes proved that XGFO can be utilized as an efficient adsorbent material for the treatment of contaminated wastewater.

Pb2+-imprinted thermosensitive antibacterial adsorbent derived from sodium alginate and PNIPAM for Pb2+ recovery

Two sodium alginate-based Pb²⁺-imprinted thermosensitive hydrogels (SPIT (without ɛ-PL) and SPPIT (with ɛ-PL)) were synthesized, with sodium alginate and ɛ-polylysine (ɛ-PL) as the matrix, N-isopropylacrylamide as the monomer. Characterization with differential scanning calorimeter, Fourier transform infrared spectroscopy, thermogravimetric analyzer, scanning electron microscopy, X-ray photoelectron spectroscopy, and Raman spectroscopy confirmed the aimed structure of the hydrogels. The adsorption capacity of SPIT and SPPIT for Pb²⁺ was 98.64 mg/g and 153.49 mg/g, respectively. Washing the Pb²⁺-loaded adsorbent with 10 °C deionized water, SPIT and SPPIT achieved a desorption efficiency of 94.59 % and 97.51 %, respectively. After 10 cycles of adsorption-desorption process, the adsorption capacity and desorption efficiency remained at about 80-88 % of the original ones, expressing excellent reusability. In a mixture containing eight metal ions (Pb²⁺, Cu²⁺, Mg²⁺, Ca²⁺, Cd²⁺, Na⁺, K⁺, Fe³⁺), the adsorption capacity of SPIT to Pb²⁺ was 92.49 mg/g, and that of SPPIT was 102.49 mg/g, much higher than that to the other ions (1.50-11.38 mg/g on SPIT, 9.48-27.45 mg/g on SPPIT), showing excellent adsorption selectivity. The introduction of ɛ-PL enhanced the adsorption capacity, antibacterial ability and stability of the hydrogel, ensuring better application potential in real wastewater.

Functionalised electrospun membranes (TETA-PVC) for the removal of lead(ii) from water

Driven by the need for delivering sustainable water purification solutions for the removal of heavy metals from water, electrospun PVC membranes were functionalised with triethylenetetramine (TETA) and were used to remove lead(ii) ions selectively from water. The membranes were characterised and their adsorption behavior towards the removal of lead from water was investigated. The incorporation of TETA on the membrane's surface significantly improved the removal efficiency of lead(ii) up to 99.8% in 30 minutes and under ambient conditions, with the lowest concentration of 50 ppm. The adsorption mechanism was investigated and kinetic data showed a better correlation with the pseudo-second-order model. Similarly, the equilibrium data best fitted with the Langmuir adsorption isotherm model with a relatively high maximum adsorption capacity of 1250 mg g⁻¹ for lead(ii) ions, larger than recently reported adsorption capacities for similar membranes. The functionalised membrane also showed high selectivity to lead(ii) in a mixed solution containing lead(ii), mercury(ii), cadmium(ii), arsenic(iii), copper(ii), and zinc(ii). The functionalised membrane was regenerated, where desorption of lead(ii) was achieved, under mildly acidic conditions. The removal efficiency of the regenerated membrane after six cycles of adsorption/desorption was maintained at a high level of 98%. The proposed design offers a simple yet effective, sustainable, and environmentally friendly solution for water treatment.

Driven by the need for delivering sustainable water purification solutions for the removal of heavy metals from water, TETA functionalised electrospun PVC membranes were fabricated and used to remove lead(ii) ions selectively from water.

Preparation of surface molecularly imprinted polymer and its application for the selective extraction of teicoplanin from water

In this study, a new surface molecularly imprinted polymer (SMIP) of teicoplanin (TEC) was prepared in an aqueous solution using amino-modified silica gel as a carrier. The molar ratio of the template molecule, functional monomer and cross-linker in the optimized synthesis system was 1 : 15 : 40. The structure and morphology of SMIP were characterized by Fourier-transform infrared spectra and scanning electron microscopy, respectively. It was shown that the silica gel modified with different active groups; the type and structure of functional monomers have a great influence on the specificity of SMIP. The SMIPs synthesized from a series of methacrylic acid and its hydroxylalkyl esters as functional monomers have good specificity for TEC. The results of static adsorption experiments showed that the adsorption capacity of SMIP was 6.5 times that of non-molecularly imprinted polymer, which were 152.6 mg g⁻¹ and 23.6 mg g⁻¹, respectively, indicating that SMIP had a larger affinity for TEC. Finally, the SMIP was successfully used as a dispersive solid-phase extraction adsorption material to selectively extract and enrich TEC from the water sample. The limit of detection of the proposed liquid chromatographic method for TEC was 5 μg L⁻¹.

A novel surface molecularly imprinted polymer for specific absorbing teicoplanin in environmental water.

Theoretical and experimental studies on the separation of cinnamyl acetate and cinnamaldehyde by adsorption onto a β-cyclodextrin polyurethane polymer

CAc and CA were separated using CDPU as adsorbent, and the mechanism was proposed through DFT calculations and experimental analyses.