Tunable fluorescent amino-functionalized Ti3C2Tx MXene quantum dots for ultrasensitive Fe3+ ion sensing

The development of sensors with high sensitivity, good selectivity and reproducibility are of great importance for the detection of Fe³⁺ in contaminated water for environmental monitoring. In this work, a reflux approach has been adopted to synthesize Ti₃C₂T_x quantum dots (QDs) based on the cutting effect of tetramethylammonium hydroxide (TMAOH) on Ti₃C₂T_x at high temperature. The surface-functionalized Ti₃C₂T_x QDs contained abundant amino groups and exhibited tunable pH-dependent emission, which was attributed to the protonation and deprotonation of the surface terminations. The linearity of the radiometric fluorescence intensity versus pH indicates its great potential as a dual-emission ratiometric pH sensor. Additionally, the Ti₃C₂T_x QDs exhibited tunable excitation-dependent emission behavior, which was related to the degree of passivation by the amino groups on the surface. Furthermore, the fluorescence intensity of the Ti₃C₂T_x QDs shows a linear response toward Fe³⁺ in the nanomolar to micromolar range with a low detection limit of 2 nM, originating from the oxidation and reduction between Fe³⁺ and Ti₃C₂T_x. This ultra-sensitive and selective detection capability demonstrated the environmental application potential for Ti₃C₂T_x QDs as a nanoprobe to monitor Fe³⁺.

Tunable electrical properties of carbon dot doped photo-responsive azobenzene-clay nanocomposites

The development of photo-responsive nanocomposite materials is important in the fabrication of optoelectronic devices. In this work, we fabricated a carbon dot doped azobenzene–clay nanocomposite which possesses different ac conductivity with and without UV treatment. At first, azobenzene nanoclusters were synthesised and then successfully used to make an azobenzene–clay nanocomposite. It was observed that there is a small change in the ac conductivity of the azobenzene–clay nanocomposite with and without UV treatment. However, this change in ac photoconductivity can be enhanced in the azobenzene–clay nanocomposite by doping with electron-rich cysteine and methionine carbon dots. Hence, ac conductivity properties of the carbon-doped azobenzene–clay nanocomposite can be tuned using UV light. Impedance measurements were determined using Electrochemical Impedance Spectroscopy. Mechanistic insight into the phenomenon is also discussed in the paper. Thus fabrication of tunable carbon dot doped photo-responsive azobenzene–clay nanocomposites will lead to the use of carbon dot doped azobenzene–clay nanocomposites in photo-switchable optoelectronic devices.

We demonstrate successful fabrication of an azobenzene–clay nanocomposite doped with electron-rich cysteine and methionine carbon dots with photo-switchable ac conductivity.

Orange-Emissive Carbon Quantum Dots: Toward Application in Wound pH Monitoring Based on Colorimetric and Fluorescent Changing

Monitoring of wound pH is critical for interpreting wound status, because early identification of wound infection or nonhealing wounds is conducive to administion of therapies at the right time. Here, novel orange-emissive carbon quantum dots (O-CDs) are synthesized via microwave-assisted heating of 1,2,4-triaminobenzene and urea aqueous solution. The as-prepared O-CDs exhibit distinctive colorimetric response to pH changing, and also display pH-sensitive fluorescence. Benefiting from the response of O-CDs over a wound-relevant pH range (5-9), medical cotton cloth is selected to immobilize O-CDs through hydrogen bond interactions, the resultant O-CDs-coated cloth with emission at 560 nm shows a high response to pH variation in the range of 5-9 via both fluorescence and visible colorimetric changes. Moreover, the sensitivity of fluorescence to pH is capable of establishing an analytical mode for determining pH value. Further, the O-CDs-based pH indicator possesses not only superior biocompatibility and drug compatibility but also excellent resistance leachability and high reversibility. Importantly, the usage of O-CDs-coated cloth to detect pH is free from the interference of blood contamination and long-term storage, thus providing a valuable strategy for wound pH monitoring through visual response and quantitative determination.

Dually emitting carbon dots as fluorescent probes for ratiometric fluorescent sensing of pH values, mercury(II), chloride and Cr(VI) via different mechanisms

The authors describe the preparation of carbon dots (CDs) that display both blue (~ 410 nm) and yellow (~ 565 nm) emission peaks. The CDs was synthesized by solvothermal treatment of o-phenylenediamine in aqueous ethyl alcohol at pH ~7.0. The CDs are shown to be useful fluorescent probes for pH values in that the ratio of fluorescences at 565 and 410 nm strongly depends on the pH value in the range from 4.5-6.5 and 10.0-13.0, respectively. The blue fluorescence is quenched by 91% by 100 µM solutions of Hg(II) through an electron transfer process, and is restored by 97% an addition of chloride (0.5 mM). The yellow fluorescence, in contrast, is hardly affected. The ratio of fluorescences at 414 and 565 nm drops linearly in the 30 to 60 μM of Hg(II) concentration range, and the limit of detection is 60 nM. Fluorescence is linearly restored in the 70 to 180 μM chloride concentration range, and the LOD is 2.8 nM. Both the blue and the yellow emission are reduced by Cr(VI) (chromate) due to an inner filter effect at pH 3.0. The ratio of fluorescences (410/565 nm) drops linearly in the 20 to 250 μM Cr(VI) concentration range, and the LOD is 260 nM. The method was utilized to analysis of chloride in salt lake brine and of Cr(VI) in spiked tap water. Graphical abstract Schematic presentation of carbon dots with pH-dependent dual emission (at ~ 410 nm and ~ 565 nm). They are shown to be viable fluorescent probes for ratiometric sensing of pH values, mercury(II), chloride and Cr(VI) via different mechanisms.

Multicolor carbon nanodots from food waste and their heavy metal ion detection application

Multicolor carbon dots (C-dots) have excellent performance characteristics, high photoluminescence efficiency, ease of fabrication and low toxicity. C-dots have been used in a wide variety of fields including bioimaging, biomedicine, photocatalysis and environmental monitoring. The mass production of multicolor CDs using low-cost, facile methods is an important issue for future industrial applications. In this article, we reported a simple and highly effective way to prepare the multicolor C-dots and use them to detect heavy metal iron ions. Hydrochar acquired from food waste processed with hydrothermal carbonization (HTC) was used as the carbonaceous material for this process. Four colors of C-dots were obtained and included blue, green, yellow and red. These multicolor C-dots could be used as fluorescence probes with unique selectivity to detect the Fe³⁺ ion. The luminescence response ranged from 1 to 50 μM with a correlation coefficient of 0.9968. This discovery not only shows the high value-added products which can be obtained from food waste but can also lead to new developments in carbonaceous materials which can be used as “green resources”.

Multicolor carbon dots produced from green carbonaceous materials by disposing of food waste through the HTC process could be used as fluorescent probes to detect iron ions.

Chiral carbon dots and their effect on the optical properties of photosensitizers

In this work, we have successfully prepared intrinsically chiral carbon dots from chiral precursors. We have also demonstrated that the chirality of these carbon dots can affect the optical properties of photosensitizer molecules like azobenzene.