Comparative Study on the Proton Conduction Behaviors of Two Acidic Amphiphilic and Hydrophilic Coordination Compounds in Nafion Composite Membranes

The acidic amphiphilic compound H[Co(H2L1)(HL1)(phen)]·3H2O (H4(Co-L1), H3L1 = 5-(3', 5'-dicarboxylphenyl)-pyridine-2-carboxylic, phen = phenanthroline) and the hydrophilic compound [Ni(HL2)(H2O)5]·H2O (H(Ni-L2), H3L2 = 5-(3',5'-dicarboxylphenyl)-pyridine-3-carboxylic) were synthesized via hydrothermal reactions at acidic conditions. The acidity of H4(Co-L1) is stronger than of H(Ni-L2); while the hydrogen bond continuity in H4(Co-L1) extended monodirectionally, which is smaller compared to the three-directional extension observed in H(Ni-L2). The proton conduction behaviors of these two compounds as fillers of Nafion composite membranes have been investigated. The results indicate that the optimal doping amounts of H4(Co-L1) and H(Ni-L2) are 2 and 1%, respectively; the proton conductivities of H4(Co-L1)/Nafion-2 and H(Ni-L2)/Nafion-1 composite membranes are 0.243 and 0.212 S·cm-1, respectively, which are approximately 50.2 and 30.6% higher than that of pure Nafion membrane, respectively. A higher doping amount of H4(Co-L1) can be attributed to its hydrophobic phen ligand, which promotes compatibility with Nafion membrane and reduces aggregation. Hydrogen bond continuity has a more significant effect on proton conductivity than acidity at relatively low doping amounts; conversely, this relationship reverses at relatively high doping amounts.

Performance and Mechanism of the Modified Group Regulated the MIL-101(Fe) Type Fenton-like Catalysts

In order to avoid the disadvantages of the Fenton process in wastewater treatment and reduce the cost of wastewater treatment, a series of MIL-101(Fe)-X (X = -OH, -NH2, -NO2, -H) solid Fenton catalysts were successfully prepared. The performance of these Fenton-like catalysts was studied with the Fenton experiment as a reference and methylene blue (MB) as an organic pollutant. The effects of the H2O2 concentration, catalyst dosage, and reaction pH on catalytic performance were systematically studied. The research had shown that the optimal concentration of H2O2 for catalytic reactions was 0.10 mmol/L and the pH was 3. At this point, their catalytic degradation MB performance was superior to the Fenton reaction and photocatalytic reaction. When the H2O2 participated in the reaction, the performance of MIL-101(Fe)-X (X = -OH, -NH2, -NO2, -H) in catalyzing the degradation of MB followed the rule of -OH > -NH2 > -NO2 > -H. This was due to the synergistic effect of Fenton-like catalysis and photocatalytic degradation in the catalytic degradation of MB. In addition, the electron paramagnetic resonance and electrospray ionization mass spectrometry showed that the hydroxyl radical (·OH) generated during the catalytic process first underwent a redox reaction with the highly electronegative functional groups in the MB molecule, and finally oxidized it to CO2 and H2O. This study successfully prepared commercially applicable Fenton-like catalysts and explored their optimal reaction conditions. This provides a technical reference for wastewater treatment.

Pyrazine-based iron metal organic frameworks (Fe-MOFs) with modulated O-Fe-N coordination for enhanced hydroxyl radical generation in Fenton-like process

Rational design of coordination environment of Fe-based metal-organic frameworks (Fe-MOFs) is still a challenge in achieving enhanced catalytic activity for Fenten-like advanced oxidation process. Here in, novel porous Fe-MOFs with modulated O-Fe-N coordination was developed by configurating amino terephthalic acid (H2ATA) and pyrazine-dicarboxylic acid (PzDC) (Fe-ATA/PzDC-7:3). PzDC ligands introduce pyridine-N sites to form O-Fe-N coordination with lower binding energy, which affect the local electronic environment of Fe-clusters in Fe-ATA, thus decreased its interfacial H2O2 activation barrier. O-Fe-N coordination also accelerate Fe(II)/Fe(III) cycling of Fe-clusters by triggering the reactive oxidant species mediated Fe(III) reduction. As such, Fe-ATA/PzDC-7:3/H2O2 system exhibited excellent degradation performance for typical antibiotic sulfamethoxazole (SMX), in which the steady-state concentration of hydroxyl radical (OH) was 1.6 times higher than that of unregulated Fe-ATA. Overall, this study highlights the role of O-Fe-N coordination and the electronic environment of Fe-clusters on regulating Fenton-like catalytic performance, and provides a platform for precise engineering of Fe-MOFs.

Regulating the interface electron distribution of iron-based MOFs through ligand functionalization enables efficient peroxymonosulfate utilization and catalytic performance

Ligand functionalization is an effective way to endow Metal-organic frameworks (MOF) with versatility for multiple applications by introducing or displaying substituents without changing the origin framework. In this work, the original MIL-101(Fe) was modified by functional groups, including -NH2, -NO2, -CH3, and -Cl substituents. The Bader charge results and electron localization function (ELF) quantitatively indicated that the functional ligands with different properties can regulate the electron structure of transition-metal centers through interface-charge redistribution. Accompanying the higher adsorption and utilization rate of peroxymonosulfate (PMS), more than 96% of acetaminophen (APAP) was degraded with a mineralization rate of 40.17% under the NH2-BDC/PMS system. In terms of mechanism, the amino group not only accelerated the regeneration of Fe(II) via the NCFe electron-transfer path, but also stimulated the appearance of high-valent Fe species. Meanwhile, the degradation pathways of APAP were proposed by integrating the results of liquid chromatograph-mass spectrometry (LC-MS) and Frontier molecular-orbital theory. Finally, the NH2-BDC/PMS system reveals long-term stability, nonselectivity, low biotoxicity as well as secondary pollution for pollutant degradation, which is a considered candidate for further environmental applications.

A Bifunctional Three-Dimensional Zn(II) Metal-Organic Framework with Strong Luminescence and Adsorption Cr(VI) Properties

The mixed ligand 3-amino-1,2,4-triazole (Hatz) and terephthalic acid (H2pta) reacted with Zn(NO3)2·6H2O to synthesize a three-dimensional binuclear Zn(II) metal-organic framework: {[Zn2·(atz)2·(pta)]·3H2O}n (3D-Zn-MOF). This 3D-Zn-MOF has two different types of pores (4.5 × 4.5 Å2, 5.7 × 5.7 Å2). The crystalline 3D-Zn-MOF could be prepared into nanomaterials (3D-N-Zn-MOF) with particles of approximately 100 nm by a cell fragmentation apparatus. Compared with the solid-state luminescence of Hatz and H2pta, it was found that 3D-N-Zn-MOF exhibited strong luminescence performance and significant red-shift phenomenon. Due to the decrease in electronegativity and rigidity of ligands, as well as the effect of ligand metal charge transfer (LMCT), the fluorescence lifetime and quantum yield of 3D-ZN-N-MOF were 2.7241 ns and 3.02%, respectively. The maximum experimental adsorption capacity of 3D-N-Zn-MOF could reach 125.52 mg/g, which was superior to the majority of MOF adsorbents under the optimal adsorption conditions (25 °C, pH = 7, and the adsorbent concentration is 0.2000 g/L). The thermodynamic analysis of adsorption showed that the adsorption of Cr(VI) by 3D-N-Zn-MOF was a spontaneous (△G < 0) and exothermic (△H < 0) process. It could be found that 3D-N-Zn-MOF was a bifunctional material with potential applications by comprehensive analysis of the fluorescence and adsorption Cr(VI) performance.

Effect of ligand substitution in UiO-66 metal-organic frameworks on the photocatalytic oxidation of acetaldehyde

A series of functionalized X-UiO-66 (X = NH2, H, Br and NO2) materials were prepared using a hydrothermal method and modified with various ligands. Their photocatalytic activity was evaluated by the oxidation of acetaldehyde. Experimental results show that the introduction of different ligands significantly influences the physicochemical properties of UiO-66. Br-UiO-66 exhibited the highest photocatalytic activity and CO2 selectivity of 85.6% and 85.7%, respectively. Photochemical properties reveal that -Br functional group facilitate the separation of photogenerated electrons and holes, significantly improving their transfer and oxygen reduction. As a result, an increased number of hydroxyl and superoxide radicals can form, improving the efficiency of the photocatalytic reaction. Br-UiO-66 accumulates fewer intermediates on its surface and still shows excellent photocatalytic activity and structural stability after 24 h of dynamic reaction. This work demonstrates the excellent adsorption and catalytic oxidation performance of Br-UiO-66 towards acetaldehyde and may provide new ideas for researching catalysts in the photocatalytic degradation of pollutants.

Visible-light-induced photocatalytic CO2 reduction over zirconium metal organic frameworks modified with different functional groups

The reduction of CO₂ into high value-added chemicals and fuels by a photocatalytic technology can relieve energy shortages and the environmental problems caused by greenhouse effects. In the current work, an amino-functionalized zirconium metal organic framework (Zr-MOF) was covalently modified with different functional groups via the condensation of Zr-MOF with 2-pyridinecarboxaldehyde (PA), salicylaldehyde (SA), benzaldehyde (BA), and trifluoroacetic acid (TA), named Zr-MOF-X (X = PA, SA, BA, and TA), respectively, through the post-synthesis modification. Compared with Zr-MOF and Zr-MOF-TA, the introduction of PA, SA, or BA into the framework of Zr-MOF can not only enhance the visible-light harvesting and CO₂ capture, but also accelerate the photogenerated charge separation and transfer, thereby improving the photocatalytic ability of Zr-MOF for CO₂ reduction. These results indicate that the modification of Zr-MOF with electron-donating groups can promote the photocatalytic CO₂ reduction. Therefore, the current work provides an instructive approach to improve the photocatalytic efficiency of CO₂ reduction through the covalent modification of MOFs.

Methylthio-functionalized UiO-66 to promote the electron-hole separation of ZnIn2S4 for boosting hydrogen evolution under visible light illumination

Solar-driven water splitting offers a leading-edge approach to storing abundant and intermittent solar energy and producing hydrogen as a clean and sustainable energy carrier. More importantly, constructing well-designed photocatalysts is a promising approach to develop clean hydrogen energy. In this paper, flower spherical UiO-66-(SCH₃)₂/ZnIn₂S₄ (UiOSC/ZIS) photocatalysts are successfully synthesized by a simple two-step hydrothermal method, and they exhibit high hydrogen production activity in light-driven water splitting. The optimized 30-UiOSC/ZIS (the content of UiOSC was 30 mg) composite exhibits optimal hydrogen production activity with a hydrogen production of 3433 μmol g^-1 h^-1, which is 5 and 235 times higher than that of pure ZIS and UiOSC, respectively. In addition, a long-cycling stability test has shown that the UiOSC/ZIS composite has good stability and recyclability. Experimental and characterization results show the formation of a type-II heterojunction between UiOSC and ZIS. This effectively suppresses the recombination of electrons-holes and promotes the carrier transfer, thus significantly improving the hydrogen production performance. This research further promotes the application of UiO-66-(SCH₃)₂ in the field of photocatalytic hydrogen production and provides a reference for the rational design of UiO-66-based composite photocatalysts.

Microwave-Assisted Rapid Substitution of Ti for Zr to Produce Bimetallic (Zr/Ti)UiO-66-NH2 with Congenetic "Shell-Core" Structure for Enhancing Photocatalytic Removal of Nitric Oxide

Efficient nitric oxide (NO) removal without nitrogen dioxide (NO₂ ) emission is desired for the control of air pollution. Herein, a series of (Zr/Ti)UiO-66-NH₂ with congenetic shell-core structure, denoted as Ti-UION, are rapidly synthesized by microwave-assisted post-synthetic modification for NO removal. The optimal Ti-UION (i.e., 2.5Ti-UION) exhibits the highest activity of 80.74% without NO₂ emission with moisture, which is 21.65% greater than that of the UiO-66-NH₂ . The NO removal efficiency of 2.5Ti-UION further increases to 95.92% without photocatalyst deactivation under an anhydrous condition. This is because selectively produced NO₂ in photocatalysis is completely adsorbed into micropores, refreshing active sites for subsequent reaction. In addition, the enhanced photocatalytic activity after Ti substitution is due to the presence of Ti electron acceptor, the potential difference between the shell and core of Ti-UION crystal, and the high conductivity of TiO units. Additionally, the improved adsorption of gas molecules not only favors NO oxidation, but also avoids the emission of NO₂ . This work provides a feasible strategy for rapid metal substitution in metal-organic frameworks and insights into enhanced NO photodegradation.

Strategies for improving the photocatalytic performance of metal-organic frameworks for CO2 reduction: A review

Photocatalytic CO₂ reduction is an appealing strategy for mitigating the environmental effects of greenhouse gases while simultaneously producing valuable carbon-neutral fuels. Numerous attempts have been made to produce effective and efficient photocatalysts for CO₂ reduction. In contrast, the selection of competitive catalysts continues to be a substantial hindrance and a considerable difficulty in the development of photocatalytic CO₂ reduction. It is vital to emphasize different techniques for building effective photocatalysts to improve CO₂ reduction performance in order to achieve a long-term sustainability. Metal-organic frameworks (MOFs) are recently emerging as a new type of photocatalysts for CO₂ reduction due to their excellent CO₂ adsorption capability and unique structural characteristics. This review examines the most recent breakthroughs in various techniques for modifying MOFs in order to improve their efficiency of photocatalytic CO₂ reduction. The advantages of MOFs using as photocatalysts are summarized, followed by different methods for enhancing their effectiveness for photocatalytic CO₂ reduction via partial ion exchange of metal clusters, design of bimetal clusters, the modification of organic linkers, and the embedding of metal complexes. For integrating MOFs with semiconductors, metallic nanoparticles (NPs), and other materials, a number of different approaches have been also reviewed. The final section of this review discusses the existing challenges and future prospects of MOFs as photocatalysts for CO₂ reduction. Hopefully, this review can stimulate intensive research on the rational design and development of more effective MOF-based photocatalysts for visible-light driven CO₂ conversion.

Regulation and photocatalytic degradation mechanism of a hydroxyl modified UiO-66 type metal organic framework

Photocatalytic performance can be effectively improved by modifying the functional groups on the organic ligands of metal organic frameworks (MOFs). Herein, the hydroxyl-modified UiO-66 type MOF: UIO-66-2OH(2,3), was successfully synthesized by the method of ligand exchange by the 2,3-dihydroxyterephthalic acid and UIO-66 as raw materials. The mechanism of photocatalytic degradation of methylene blue (MB) by UIO-66-2OH(2,3) shows that the hydroxyl functional group on the organic ligand regulates its electronegativity and expands its light absorption range. The decomposition of MB is carried out in multiple steps under the oxidation of the hydroxyl radical (˙OH). This research result shows the direction for guiding the synthesis of efficient photocatalysts and clarifying the light absorption of MOFs regulated by hydroxyl functional groups.

Enhanced photocatalytic performance over PANI/NH2-MIL-101(Fe) with tight interfacial contact

Constructing a suitable heterojunction structure while maintaining a tight interface to promote the separation of photogenerated electrons is of great significance for improving the photocatalytic activity. In this paper, a new PANI/NH₂-MIL-101(Fe) II-scheme heterojunction was prepared by a hydrothermal method. PANI with a porous structure was firstly obtained by the template method, and then PANI fragments were loaded on the surface of NH₂-MIL-101(Fe) crystals under hydrothermal conditions to obtain a PANI/NH₂-MIL-101(Fe) photocatalyst. The photocatalytic degradation of TC under simulated sunlight can reach 90% within an hour, and the maximum hydrogen evolution rate is 7040 μmol g^-1 h^-1 under visible light. The enhanced catalytic performance of PANI/NH₂-MIL-101(Fe) was attributed to the appropriate matching of the VB and CB of PANI and NH₂-MIL-101(Fe), and secondly, the coordination bonds formed between PANI and NH₂-MIL-101(Fe) provided a channel for charge separation and transfer. Finally, a possible mechanism of the photocatalytic system was proposed through a free radical capture experiment and characterization analysis. More importantly, the experiment proved that the heterojunction formed by PANI and NH₂-MIL-101(Fe) can achieve the effect of complementing each other, which provides a feasible idea and method for the design of efficient heterojunction photocatalysts.

In Situ Synthesis Mechanism and Photocatalytic Performance of Cyano-Bridged Cu (I)/Cu (II) Ultrathin Nanosheets

In situ synthesis of cyano-bridged Cu (I)/Cu (II) complexes usually requires organometallic catalysts or is carried out under high-temperature and high-pressure conditions. Herein, the cyano-bridged two-dimensional Cu (I)/Cu (II) photocatalyst, [Cu₂ (Py)₃(CN)₃]_n (1), is synthesized in situ at room temperature. The in situ synthesis mechanism of 1 shows that the partial Cu (II) complex catalyzed the C-C bond cleavage of 1,3-isophthalonitrile (L) to introduce -CN and generate Cu (I)/Cu (II). Its ultrathin nanosheets can be obtained by adding sodium dodecyl benzene sulfonate and performing ultrasonic synthesis in the process of synthesis 1. The ultrathin nanosheets of 1 have a lattice distance of about 0.31 nm, and it can rapidly decompose methylene blue (MB) (K = 0.25 mg L⁻¹ min⁻¹ at pH = 3). This research work is beneficial for in situ synthesis of cyano-bridged Cu (I)/Cu (II) complexes at room temperature and explores their synthesis and photocatalytic mechanism.

Effects of Different Delocalized π-Conjugated Systems Towards the TiO2-Based Hybrid Photocatalysts

Modulating the structure of a photocatalyst at the molecular level can improve the photocatalytic efficiency and provides a guide for the synthesis of highly qualified photocatalysts. In this study, TiO2 was modified by various organic compounds to form different TiO2-based hybrid photocatalysts. 1,10-Phenanthroline (Phen) is an organic material with delocalized π-conjugated systems. It was used to modify TiO2 to form the hybrid photocatalyst Phen/TiO2. Furthermore, 1,10-phenanthrolin-5-amine (Phen-NH2) and 1,10-phenanthroline-5-nitro (Phen-NO2) were also used to modify TiO2 to form NH2-Phen/TiO2 and NO2-Phen/TiO2, respectively. The samples of TiO2, Phen/TiO2, NO2-Phen/TiO2, and NH2-Phen/TiO2 were carefully characterized, and their photocatalytic performance was compared. The results indicated that the photocatalytic efficiency followed the order of NH2-Phen/TiO2 > NO2-Phen/TiO2 > Phen/TiO2 > TiO2. It could be found that modifying TiO2 with different organic compounds containing delocalized π-conjugated systems could enhance the photocatalytic ability; furthermore, the level of this enhancement could be modulated by different delocalized π-conjugated systems.

Metal-Based Nanocomposite Materials for Efficient Photocatalytic Degradation of Phenanthrene from Aqueous Solutions

Polycyclic aromatic hydrocarbons (PAHs) are a class of naturally occurring chemicals resulting from the insufficient combustion of fossil fuels. Among the PAHs, phenanthrene is one of the most studied compounds in the marine ecosystems. The damaging effects of phenanthrene on the environment are increasing day by day globally. To lessen its effect on the environment, it is essential to remove phenanthrene from the water resources in particular and the environment in general through advanced treatment methods such as photocatalytic degradation with high-performance characteristics and low cost. Therefore, the combination of metals or amalgamation of bimetallic oxides as an efficient photocatalyst demonstrated its propitiousness for the degradation of phenanthrene from aqueous solutions. Here, we reviewed the different nanocomposite materials as a photocatalyst, the mechanism and reactions to the treatment of phenanthrene, as well as the influence of other variables on the rate of phenanthrene degradation.

Facile Strategy for Efficient Charge Separation and High Photoactivity of Mixed-Linker MOFs

Two new sets of UiO-Zr metal-organic framework (MOF) bearing mixed linkers BDC-(SCH₃)₂ and BDC-(SOCH₃)₂ that have different band gaps and edges were prepared through post oxidation and direct methods, namely, UiO-66-(SCH₃)₂-xh (x = 4, 9, 12 oxidation hours) and UiO-66-(SOCH₃)_x(SCH₃)_2-x (x = 0, 0.4, 0.6, 2), respectively. These composites with stoichiometric components were fully characterized via proton nuclear magnetic resonance (¹H NMR) spectroscopy, powder X-ray diffraction (PXRD), transmission electron microscopy (TEM), Fourier-transform infrared (FT-IR) spectra, Brunauer-Emmett-Teller (BET), photo electrochemical measurements, and femtosecond transient absorption (fs-TA) spectroscopy. The structure, electronic property, and photoresponsive and catalytic ability as the functions of the molar ratio of linkers and the synthetic protocol were first investigated. The mixed-linker UiO-66-(SCH₃)₂-xh and UiO-66-(SOCH₃)_x(SCH₃)_2-x exhibited improved performances as compared to the UiO-66-(SCH₃)₂ and UiO-66-(SOCH₃)₂ possessing neat linkers only. Their photo response and catalytic activity varied with different linker ratios. For UiO-66-(SCH₃)₂-xh, the performance increased with the increasing linker BDC-(SOCH₃)₂ ratio upon oxidation but reached the highest as the BDC-(SOCH₃)₂ being of 24.4% in UiO-66-(SCH₃)₂-9h. In comparison, the best photocurrent (80.74 uA/cm^-2) and the highest H₂ generation rate (2018.8 μmol g^-1 h^-1) (λ > 400 nm) in UiO-66-(SCH₃)₂-9h are about twice those of UiO-66-(SOCH₃)_0.4(SCH₃)_1.6 obtained by direct synthesis, although the linker BDC-(SOCH₃)₂ ratio of those two composites is almost the same (24.4% vs 23.9%). Recorded shorter lifetime and higher charge separation efficiency of the former than those of the latter suggest the postsynthetic protocol as the efficient method for achieving the mixed-liner-MOF-based photocatalyst with high performance. A new type-II tailored homojunction is proposed in these mixed-linker MOFs for their efficient charge separation and improved activity.

Tuning the Optoelectronic Properties of Hybrid Functionalized MIL-125-NH2 for Photocatalytic Hydrogen Evolution

Metal-organic frameworks (MOFs) constructed with mixed ligands have shown great promise in the generation of materials with improved sorption, optical, and electronic properties. With an experimental, spectroscopic, and computational approach, herein, we investigated how the incorporation of different functionalized ligands within the structure of MIL-125-NH₂ affects its performance in photocatalytic water reduction. We found that multiligand incorporation within the MOF structure has an impact on the light absorption spectrum and the electronic structure. These combined modifications improve the photocatalytic performance of MIL-125-NH₂, thereby increasing the rate of hydrogen evolution reaction. Of the four nanoparticle/MOF photocatalytic systems tested, we showed that the Pt/MIL-125-NH₂/(OH)₂ system (Pt nanoparticle plus MIL-125-NH₂ with amino and dihydroxyl functionalized ligands) outperforms its counterpart Pt/MIL-125-NH₂ system, attributed to the enhanced p-π conjugation between the lone pairs of O atoms and their aromatic ligands resulting in a red-shifted absorption spectrum and greater spatial distribution of electron density.

2D WS2 co-catalysts induce the growth of CdS and enhance the photocatalytic performance

Here, we obtain WS₂ nanosheets with near-infrared absorption which can replace the precious metal Pt as excellent cocatalysts.

Enhanced photocatalysis using metal-organic framework MIL-101(Fe) for organophosphate degradation in water

Metal-organic frameworks (MOFs) are attractive novel classes of porous materials with diverse potentiality and easily tailored structures. It is desirable to evaluate the performance of MOFs as photocatalysts for organic contaminant removal in aqueous matrixes. In this study, iron-based MIL-101(Fe) was synthesized and a photo-Fenton reaction system (multiple wavelength light + MIL-101(Fe) + H₂O₂) was developed for elimination of tris(2-chloroethyl) phosphate (TCEP). Degradation pattern of TCEP followed an S-shape curve, which included a slow induction period and a rapid radical oxidation process. Transport of reactants into MIL-101(Fe) and the activation of electron transport within Fe-O clusters of MIL-101(Fe) may be the dominant mechanisms in the induction period, while a pseudo-first-order kinetics was observed in the hydroxyl radical oxidation process. Removal efficiencies in these two stages highly depended on the reaction conditions. Irradiation at 420 nm and acid condition were conductive, while high temperature and high [H₂O₂]:[MIL-101(Fe)] mass ratio accelerated the reaction. Before complete mineralization, eleven degradation products were generated, and the dominant degradation pathways included cleavage, hydroxylation, carbonylation, and carboxylation. Under acid condition (pH = 3), only 1% mass loss was observed after 60-min reaction, but the iron leakage was aggravated when pH increased. Furthermore, this MOF-photo-Fenton system demonstrated a robust performance on TCEP degradation in actual wastewater matrixes under acid condition. Generally, the MOF-photo-Fenton system is a potential technology for elimination of organic pollutants in aqueous solution.

In situ synthesis and photocatalytic mechanism of a cyano bridged Cu(i) polymer

A one-dimensional copper(i) nanorod polymer [Cu(L)₂·(CN)]_n (1) (L = 4(3H)-quinazolone), was formed in situ by C–C bond cleavage of acetonitrile.