Development of a molecularly imprinted polymer on silanized graphene oxide for the detection of 17-estradiol in wastewater

This research article demonstrates the synthesis, characterization, and electrochemical evaluation of a molecularly imprinted polymer (MIP) on the surface of silanized graphene oxide (silanized GO), which is nanostructured and used to quantify 17-estradiol (E2) in wastewater. As characterization methods, X-ray diffraction (XRD), Raman spectroscopy, dynamic scattering light (DSL), scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FTIR) were utilized to examine the synthesized GO, silanized GO, MIP-GO composite, and non-imprinted polymer (NIP)-GO (NIP-GO) composite. FTIR results confirmed the successful synthesis of GO composites. Raman study confirmed the synthesis of monolayer silanized GO, MIP-GO composite, and NIP-GO composite. Surface morphology revealed that after polymerization, the surface of silanized GO sheet-like morphology is covered with nanoparticles. Adsorption kinetics studies revealed that adsorption follows the pseudo-second-order kinetics. Further, we studied the performance of a MIP-GO-based sensor by optimizing the effects of pH, scan rate, and incubation period. The linear calibration was achieved between the oxidation peak current and E2 concentration from 0.1 to 0.81 ppm, with a detection limit of 0.037 ppm. The selectivity of the MIP-GO composite was also checked by using other estrogens, and it was found that E2 is 3.3, 0.5, and 1.4 times more selective than equilin, estriol, and estrone, respectively. The composite was successfully applied to the wastewater samples for the detection of E2, and a good percentage of recoveries were achieved. It suggests that the reported composite can be applied to real samples. PRACTITIONER POINTS: An innovative electrochemical sensor was developed for selective detection of 17-estradiol through molecularly imprinted polymer fabricated on the surface of silanized GO (MIP-GO composite). The developed method was comprehensively validated and found to be linear in the range of 0.1 to 0.8 ppm of 17-estradiol, with 0.037 ppm of limit of detection and 0.1 ppm of limit of quantification, respectively. The developed MIP-GO-composite-based electrochemical sensor was found 3.3, 0.5, and 1.4 times more selective for 17-estradiol than equiline, estriol, and estrone, respectively. The applicability of a developed sensor was also checked on wastewater samples, and a good percent recovery was obtained.

Green Prospective Approach of Chromium Zinc Oxide Nanoparticles for Highly Ultrasensitive Electrochemical Detection of Anti-hypotensive Medication in Various Matrices

A highly ultrasensitive sensor that relied on Cr/ZnO-NPs was developed to detect etilefrine hydrochloride (ETF) in different matrices via a particular green voltammetric technique. The X-ray diffraction pattern showed the nanomaterials of the polycrystalline hexagonal structure. The energy-dispersive X-ray spectrum approved the presence of Cr3+ inside the host zinc oxide framework. The morphological and topological characteristics were visualized using transmission electron microscopy and atomic force microscopy micrographs describing the nanoparticles in spherical-like shape with large-surface area. The energy gap (Eg) was evaluated from transmittance (T %) and reflectance (R %) spectra within the visible region. The optimization study indicated that the Cr/ZnO-NP/CPE sensor has high sensitivity, thanks to the distinctive physical and chemical properties of the fabricated electrode. A new approach showed a great selectivity for determining ETF in different matrices in the presence of other interferents like levodopa. Under optimal circumstances, the square-wave voltammetry revealed a linear response to ETF from 0.01 to 10 μmol L-1 (r = 0.9996) with quantification and detection limits of 9.11 and 2.97 nmol L-1, respectively. Finally, the proposed approach was effectively applied to estimate ETF in pharmaceutical dosage forms and biological fluids using simple, accurate, and selective electrochemical electrode. The greenness profile assessment of the developed method was performed using the Eco-Scale and green analytical procedure index. These tools indicated that the proposed method is an eco-friendly technique for the determination of ETF in different matrices.

Non-enzymatic electrochemical detection of creatinine based on a glassy carbon electrode modified with a Pd/Cu2O decorated polypyrrole (PPy) nanocomposite: an analytical approach

The major constraints of standard enzymatic biosensors are poor long-term storage stability and high cost. Hence, there is extensive research towards fabrication of reliable enzymeless biosensors based on nanomaterials. In this paper, we present the development of an enzymeless electrochemical biosensor for highly precise detection of creatinine. This involves the use of a simple yet effective alternative to the commonly utilized Pd/Cu₂O/PPy nanocomposite, which was characterized by different analytical methods. The present electrochemical sensor provides a wide detection range (0.1 to 150 μM), low detection limit (0.05 μM) and high sensitivity (0.207 μA), and is capable of detecting the creatinine level in human urine samples, which are inexpensive. The results are reproducible, and the sensor is stable. The sensor demonstrates good electrocatalytic activity and selectivity towards the detection of creatinine in the presence of various other similar biological entities. When compared to other existing counterparts, the electrocatalytic behaviour of the present sensor is comparable, if not better. So, the present electrochemical sensor for creatinine might be employed as a long-term diagnostic alternative.

AuNPs and graphdiyne nanocomposite as robust electrocatalyst for methyl parathion detection in real samples

The present work describes a simple and rapid synthesis method of gold nanoparticles and graphdiyne (AuNPs@GDY) nanocomposites including porous structure. Moreover, the synthesized AuNPs@GDY material was decorated on the glassy carbon electrode (GCE) with a drop coating method to construct a non-enzymatic electrochemical pesticides sensor. The micro-morphology and elemental composition of the materials were characterized by transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS). The electrocatalysis and conductivity of the material were studied with cyclic voltammetry (CV) and impedance method, respectively. The properties of the sensor were investigated by CV and differential pulse voltammetry (DPV). The results showed that AuNPs@GDY exhibited excellent electrocatalytic ability for methyl parathion in a wide linear range (from 0.25 ng/mL to 24.43 μg/mL) and low limit of detection value (6.2 pg/mL). Furthermore, the DPV method used in this paper was accurate and sensitive, and could be used for routine quality control of methyl parathion in kiwi fruit and tomato samples.

Strategies, advances, and challenges associated with the use of graphene-based nanocomposites for electrochemical biosensors

Graphene is an intriguing two-dimensional honeycomb-like carbon material with a unique basal plane structure, charge carrier mobility, thermal conductivity, wide electrochemical spectrum, and unusual physicochemical properties. Therefore, it has attracted considerable scientific interest in the field of nanoscience and bionanotechnology. The high specific surface area of graphene allows it to support high biomolecule loading for good detection sensitivity. As such, graphene, graphene oxide (GO), and reduced GO are excellent materials for the fabrication of new nanocomposites and electrochemical sensors. Graphene has been widely used as a chemical building block and/or scaffold with various materials to create highly sensitive and selective electrochemical sensing microdevices. Over the past decade, significant advancements have been made by utilizing graphene and graphene-based nanocomposites to design electrochemical sensors with enhanced analytical performance. This review focus on the synthetic strategies, as well as the structure-to-function studies of graphene, electrochemistry, novel multi nanocomposites combining graphene, limit of detection, stability, sensitivity, assay time. Finally, the review describes the challenges, strategies and outlook on the future development of graphene sensors technology that would be usable for the internet of things are also highlighted.

Advances of Drugs Electroanalysis Based on Direct Electrochemical Redox on Electrodes: A Review

The strong development of mankind is inseparable from the proper use of drugs, and the electroanalytical research of drugs occupies an important position in the field of analytical chemistry. This review mainly elaborates the research progress of drugs electroanalysis based on direct electrochemical redox on various electrodes for the recent decade from 2011 to 2021. At first, we summarize some frequently used electrochemical data processing and electrochemical mechanism research derivation methods in the literature. Then, according to the drug therapeutic and application/usage purposes, the research progress of drugs electrochemical analysis is classified and discussed, where we focus on drugs electrochemical reaction mechanism. At the same time, the comparisons of electrochemical sensing performance of the drugs on various electrodes from recent studies are listed, so that readers can more intuitively compare and understand the electroanalytical sensing performance of each modified electrode for each of the drug. Finally, this review discusses the shortcomings and prospects of the drugs electroanalysis based on direct electrochemical redox research.

Simultaneous and selective electrochemical sensing of methotrexate and folic acid in biological fluids and pharmaceutical samples using Fe3O4/ppy/Pd nanocomposite modified screen printed graphite electrode

The purpose of this study was to fabricate an electrochemical sensor for the detection of methotrexate and folic acid based on a screen-printed graphite electrode (SPGE) modified with prepared iron oxide (Fe₃O₄)/polypyrrole (ppy)/Palladium (Pd) nanocomposite. Transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FT-IR) techniques were employed to characterize the Fe₃O₄/ppy/Pd nanocomposite. The produced modifier was used to induce a remarkable electrocatalytic impact relative to the oxidation of methotrexate, which caused the potential peak shift to a less positive amount (from 800 mV to about 500 mV) and improved the peak current (from 5.3 μA to about 16 μA). Methotrexate peak current was linearly dependent on its concentration from 0.03100.0 μM and the limit of detection (LOD) was estimated at 7.0 nM. The methotrexate and folic acid were co-detected by the proposed sensor. The experimental results indicated that the oxidation peaks of methotrexate and folic acid were separated about 200 mV in phosphate buffer solution (PBS) at pH 7.0. Fe₃O₄/ppy/Pd/SPGE was successfully able to detect methotrexate and folic acid in pharmaceutical and biological samples with excellent recovery.

Highly sensitive detection of anti-cancer drug based on bimetallic reduced graphene oxide nanocomposite

Herein, we describe a high-performance electrochemical sensor for the detection of regorafenib (REG) using bimetallic Pd-Ru nanoparticles anchored on pomegranate peel extract (PPE) derived reduced graphene oxide (Pd-Ru/rGO). PPE was employed to neutralize the extremely acidic graphene then cast-off along with the metal precursor for the duration of the chemical reduction to accomplish well dispersed Pd-Ru nanoparticles. Bimetallic Pd-Ru/rGO nanocomposites were synthesized using a facile chemical reduction method. Under optimal conditions, based on the differential pulse voltammetric studies it has been confirmed that the fabricated sensors has good electrocatalytic activity toward the detection of REG, spanning over the linear dynamic range of 0.5-300 nM. Moreover, the sensor exhibited a low limit of detection of 1.6 nM and a limit of quantification of 4.8 nM. The electrochemical sensor unveiled admirable selectivity and sensitivity, reproducibility, and repeatability. The fabricated sensor was suitable for real sample analysis (pharmaceutical tablet, human blood plasm, wastewater) with satisfactory recovery. The strategy presented herein can be employed in the development of electrochemical sensors for other target analytes.

An electrochemical sensor based on a glassy carbon electrode modified with sandwich structured ZIF-67@rGO for bisphenol A measurement

The low conductivity of metal-organic frameworks seriously impedes their electrocatalytic performance. In this study, we prepared a fabricated sandwich structure composed of a Co-based zeolitic imidazolate framework (ZIF-67) and reduced graphene oxide (rGO) through a facile and simple one-pot hydrothermal reaction. This framework of nanocomposites, which are modified with a glassy carbon electrode, constructed a bisphenol A (BPA) electrochemical sensor for the first time. Operational parameters such as pH, electrolytes, the amount of modifiers, deposition potentials and deposition time were optimised for the sensitive detection of BPA. The performance of electrodes was evaluated by cyclic voltammetry, electrochemical impedance spectroscopy, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction and transmission electron microscopy. With differential pulse voltammetry, the detection concentration of BPA ranged from 0.05 μmol L^-1 to 100 μmol L^-1. The results revealed that the hierarchical nanocomposites demonstrated better electrocatalytic performance with large electrochemically active surface areas, high sensitivity and a low limit of detection (5.2 nmol L^-1), compared with a physical mixture of ZIF-67 and rGO at the same ratio. These impressive features originate from the synergistic effects of ZIF-67 and rGO. This study presents a new strategy using metal-organic framework composite materials for the sensitive detection of BPA.

A 2D/2D NiCo-MOF/Ti3C2 heterostructure for the simultaneous detection of acetaminophen, dopamine and uric acid by differential pulse voltammetry

A 2D/2D NiCo-MOF/Ti₃C₂ heterojunction is constructed as a non-enzymatic biosensor for the simultaneous electrochemical detection of acetaminophen (AP), dopamine (DA), and uric acid (UA) via differential pulse voltammetry. Benefiting from the synergistic effects of the high electrocatalytic activity of NiCo-MOF, the outstanding conductivity of Ti₃C₂, and the improved specific surface area of NiCo-MOF/Ti₃C₂, NiCo-MOF/Ti₃C₂ displays high sensing performance toward AP (0.01-400 μM), DA (0.01-300 μM), and UA (0.01-350 μM) in 0.1 M phosphate buffer (PB, pH 7.4) at working potentials of 0.346 V vs. SCE for AP, 0.138 V vs. SCE for DA, and 0.266 V vs. SCE for UA. Furthermore, the well-separated oxidation peak potentials allow for the simultaneous detection of the analytes, with detection limits of 0.008, 0.004, and 0.006 μM (S/N = 3), respectively. As a result of its considerable reproducibility and anti-interference and anti-fouling properties, NiCo-MOF/Ti₃C₂ was also developed into a practical sensing platform to detect AP, DA, and UA in serum and urine, presenting excellent recoveries of 98.1-102.2 %.

Graphene oxide@Ce-doped TiO2 nanoparticles as electrocatalyst materials for voltammetric detection of hazardous methyl parathion

A sensitive voltammetric sensor has been developed for hazardous methyl parathion detection (MP) using graphene oxide@Ce-doped TiO₂ nanoparticle (GO@Ce-doped TiO₂ NP) electrocatalyst. The GO@Ce-doped TiO₂ NPs were prepared through the sol-gel method and characterized by various physicochemical and electrochemical techniques. The GO@Ce-doped TiO₂ NP-modified glassy carbon electrode (GCE) addresses excellent electrocatalytic activity towards MP detection for environmental safety and protection. The developed strategy of GO@Ce-doped TiO₂ NPs at GCE surfaces for MP detection achieved excellent sensitivity (2.359 μA μM^-1 cm^-2) and a low detection limit (LOD) 0.0016 μM with a wide linear range (0.002 to 48.327 μM). Moreover, the fabricated sensor shows high selectivity and long-term stability towards MP detection; this significant electrode further paves the way for real-time monitoring of environmental quantitative samples with satisfying recoveries.

Cadmium sulfide quantum dots anchored on reduced graphene oxide for the electrochemical detection of metronidazole

In this research, the metal–organic-based synthesis of cadmium sulfide quantum dots (CdS QDs) was performed.

Synthesis of a magnetic sorbent and its application in extraction of different pesticides from water, fruit, and vegetable samples prior to their determination by gas chromatography-tandem mass spectrometry

In this investigation, an efficient sorbent based on Fe₃O₄@polyphenols magnetic nanoparticles has been prepared using the extract of Mentha piperita leaves for the first time. The main purposes of this study were synthesis of economically affordable and environmentally friendly sorbent using the extract of Mentha piperita leaves and evaluating its application as a sorbent in magnetic solid phase extraction. The functional groups, magnetic property, size, and shape of the synthesized sorbent were characterized. The sorbent was utilized for the extraction and preconcentration of various pesticides (chlorpyrifos, fenazaquin, penconazole, diniconazole, oxadiazon, haloxyfop-methyl, hexaconazole, clodinafop-propargyl, tebuconazole, and fenoxaprop-p-ethyl) from vegetable, fruit, and water samples. After magnetic solid phase extraction, a dispersive liquid-liquid microextraction method was done to achieve low detection limits. The enriched pesticides were monitored by gas chromatography-tandem mass spectrometry. The synthesized sorbent was characterized by Fourier transform infrared, scanning electron microscopy, energy-dispersive x-ray spectroscopy, x-ray diffraction, and vibrating sample magnetometer techniques, which confirmed the successful synthesis of the magnetic nanoparticles. The effective parameters such as the sorbent weight, ionic strength, pH, vortex time, and kind and volume of elution and extraction solvents were studied. Under optimum extraction conditions, the method showed broad linear ranges (0.05-1000 µg L^-1) with low limits of detection (0.27-4.13 ng L^-1) and quantification (0.91-13.8 ng L^-1). Extraction recoveries and enrichment factors were in the ranges of 54-89 % and 491-811, respectively.

Simultaneous determination of ascorbic acid, uric acid and dopamine using silver nanoparticles and copper monoamino-phthalocyanine functionalised acrylate polymer

A silver nanoparticle and copper monoamino-phthalocyanine-acrylate (Cu-MAPA) polymer modified glassy carbon electrode was developed for the simultaneous detection of dopamine (DOP), ascorbic acid (AA) and uric acid (UA) using voltammetric techniques. Silver nanoparticles (AgNPs) were synthesised according to the citrate reduction method. Following synthesis and characterisation the copper phthalocyanine polymer was co-deposited with AgNPs realising a surface with enhanced electron transfer which lowered the overpotential required for analyte electro-oxidation. Differential pulse voltammetry (DPV) was employed for the simultaneous determination of dopamine (DOP), ascorbic acid (AA) and uric acid (UA) at AgNP/Cu-MAPA modified surfaces at <μM ranges. The peak potential separations for DOP-AA and DOP-UA were ca. 181 mV and 168 mV respectively. The chemical sensor was also capable of individual quantitation of DOP, UA and AA with detection limits of 0.7, 2.5 and 5.0 nM respectively. Overall, the approach realised a simple and effective electrode modifier for the selective discrimination and quantitation of DOP in the presence of physiological levels of AA and UA.

Electrochemical determination of caffeic acid in antioxidant beverages samples via a facile synthesis of carbon/iron-based active electrocatalyst

An electrochemical method has described for the voltammetric determination and oxidation of caffeic acid (CA) at a glassy carbon electrode (GCE) modified carbon/iron-based active catalyst as a sensing platform. In this study, we have developed a highly sensitive electrochemical CA sensor with f-MWCNTs/α-NaFeO₂ composite, which was developed by a simple ultrasonication method. The microstructural features of the f-MWCNTs/α-NaFeO₂ composite characterized by different physicochemical and analytical techniques. Under the optimized condition, the developed sensor archive the ultra-sensitivity (44.6859 μA μM^-1cm^-2) at a lower concentration with excellent linearity (R² = 0.9943) and which shows low detection limit (LOD = 0.002 μM) and Limit of quantification (LOQ = 0.0068 μM) by using differential pulse voltammetry (DPV) technique. The suggested sensor may improve the effective and efficient platform to the determination of CA in the healthcare system.

Electrochemical detection of β-lactoglobulin based on a highly selective DNA aptamer and flower-like Au@BiVO4 microspheres

Beta-lactoglobulin is a natural milk protein and the main cause of infant milk allergy. In this work, a sensitive, selective and inexpensive electrochemical biosensor for the detection of β-lactoglobulin was developed. In this sensor, a DNA aptamer was used instead of an expensive antibody as the recognition group highly selective for β-lactoglobulin. The flower-like BiVO₄ microspheres were firstly found to have peroxidase mimic catalytic activity and used to amplify the electrochemical signal. The aptamer can bind β-lactoglobulin and fall off from the working electrode, after which the DNA2/Au/BiVO₄ probe can be fixed to the DNA1/AuNPs/ITO working electrode by the hybridization of DNA2 with DNA1. Therefore, a higher concentration of β-lactoglobulin leads to increased fabrication of the DNA2/Au/BiVO₄ probe on the surface of the working electrode, and thereby increases the electrochemical signal. This electrochemical biosensor exhibited a wide detection range from 0.01 to 1000 ng mL^-1, with a limit of detection (LOD) of 0.007 ng mL^-1, which indicates a good potential application in the field of food analysis.

Highly dispersive Pt-Pd nanoparticles on graphene oxide sheathed carbon fiber microelectrodes for electrochemical detection of H2O2 released from living cells

We report a facile strategy for the synthesis of surfactant-free, small and highly dispersive Pt-Pd nanoparticles on graphene oxide (Pt-Pd NPs/GO) by an electroless deposition method, which is sheathed on carbon fiber microelectrodes (CFMs) as an electrochemical sensing platform for highly sensitive and selective detection of hydrogen peroxide (H₂O₂) released from the living cells. GO serves as the reducing agent and stabilizer for electroless deposition of Pd NPs on the surface of GO owing to its low work function (4.38 eV) and highly conjugated electronic structure. The obtained Pd NPs/GO have a relatively high work function (4.64 eV), and thereby could be used as stabilizer for synthesis of surfactant-free, small and highly dispersive Pt-Pd NPs/GO by chemical reduction of K₂PtCl₄. The obtained Pt-Pd NPs have a uniform size of 4.0 ± 0.6 nm on the surface of GO. Moreover, the Pt-Pd NPs/GO sheathed CFMs exhibit an excellent electrocatalytic activity for the reduction of H₂O₂ with a low detection limit of 0.3 μM and good selectivity. These good properties enable the modified microelectrode to detect the H₂O₂ released from living cells.

Rapid detection of low concentration CO using Pt-loaded ZnO nanosheets

Unloaded and Pt-loaded ZnO nanosheets with 120-170 nm sizes were successfully synthesized by a facile one-pot hydrothermal route followed by a calcination treatment. The as-synthesized samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). It can be clearly observed that Pt nanoparticles with the diameter of 3-5 nm were uniformly loaded on the surface of ZnO nanosheets. A contrastive study based on CO gas sensing performance of bare ZnO and Pt/ZnO was carried out. According to the measurement results, the loading of Pt remarkably upgraded the sensing capability toward CO. The 0.50 at.% Pt/ZnO based gas sensor exhibited an obvious response value of 3.57 toward 50 ppm CO and fast response/recovery time (6/19 s). Besides, the detection limit was as low as 0.10 ppm and the optimal operating temperature was decreased from 210 °C to 180 °C. The enhanced CO sensing performance by Pt nanoparticles could be attributed to the combination of chemical sensitization and electronic sensitization. The 0.50 at.% Pt/ZnO is an efficient sensor material for rapidly detecting low-concentration CO.

Enhanced sensing of hazardous 4-nitrophenol by a graphene oxide–TiO2 composite: environmental pollutant monitoring applications

The accurate detection of hazardous 4-nitrophenol (4-NP) is deemed essential for the environment and human health.

Plasmonic spectral determination of Hg(II) based on surface etching of Au-Ag core-shell triangular nanoplates: From spectrum peak to dip

In this work, we develop a simple and selective sensing method for the detection of mercury ions based on surface plasmon resonance (SPR) spectrum change of Au-Ag core-shell triangular nanoplates. When the concentration of mercury is increased, the etching-induced change of particle size and shape also leads to the decrease of the absorption peak at the fixed wavelength, until a spectrum dip takes place. This spectral change of "peak-to-dip" greatly enlarges the detection range of mercury ions, which could be fine tuned by changing the initial thickness of the Ag coating. Under optimal conditions, the decrease of the logarithmic absorption intensity has a good linear response with the concentration of mercury ions increasing from 10 to 1000 μM, and the limit of detection (LOD) is 0.88 μM. Interference studies and real samples test indicate that, this new sensing method has a good selection for mercury ions and can be practically used in lake water. This work shows the surface etching-induced SPR shift can also leads to the intensity change with "peak-to-dip" fashion, which greatly enlarge the concentration range of the detection and could be widely applied in the spectroscopy sensing based on SPR.

Highly Sensitive Electrochemical Sensor for Anticancer Drug by a Zirconia Nanoparticle-Decorated Reduced Graphene Oxide Nanocomposite

Because of their large surface area and conductivity, some inorganic materials have emerged as good candidates for the trace-level detection of pharmaceutical drugs. In the present work, we demonstrate the detection of an anticancer drug (regorafenib, REG) by using an electrochemical sensor based on a nanocomposite material. We synthesized a zirconia-nanoparticle-decorated reduced graphene oxide composite (ZrO2/rGO) using a one-pot hydrothermal method. Reduction of the graphene oxide supports of the Zr2+ ions with hydrazine hydrate helped in preventing the agglomeration of the zirconia nanoparticles and in obtaining an excellent electrocatalytic response of the nanostructure ZrO2/rGO-based electrochemical sensor. Structural and morphological characterization of the nanostructure ZrO2/rGO was performed using various analytical methods. A novel regorafenib (REG) electrochemical sensor was fabricated by immobilizing the as-prepared nanostructure ZrO2/rGO on to a glassy carbon electrode (GCE). The resulting ZrO2/rGO/GCE could be used for the rapid and selective determination of REG in the presence of ascorbic acid and uric acid. The ZrO2/rGO/GCE showed a linear response for the REG analysis in the dynamic range 11-343 nM, with a remarkable lower detection limit and limit of quantifications of 17 and 59 nM, respectively. The newly developed sensor was used for the accurate determination of REG in both serum samples and pharmaceutical formulations, with satisfactory results.

Development of a microcomposite with single-walled carbon nanotubes and Nd2O3 for determination of paracetamol in pharmaceutical dosage by adsorptive voltammetry

This study presents for the first time a new composite of carbon paste (CP), single-walled carbon nanotubes (SWCNTs) and Nd₂O₃ (Nd_OX). This versatile composite (Nd_OX-SWCNT/CPE) was applied to the oxidation of paracetamol (PCM). The newly formed surface was characterized by scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The results showed greater conductivity and a higher surface area for the composite than those of the carbon paste alone. Moreover, the anodic peak currents for PCM increased from 1.6 to 3.6 µA with CPE and Nd_OX-SWCNT/CPE, indicating an increase of nearly 51.0% for the anodic peak current. On the other hand, the anodic peak potentials shifted from 0.67 to 0.57 V. The detection limits were 0.05 µmol/L with Nd_OX-SWCNT/CPE and 0.50 µmol/L with SWCNT/CPE. The relative standard deviations (RSDs) were 1.5% (n = 7). The accuracy and interference of the methods were evaluated with a urine chemistry control spiked with known quantities of PCM, uric acid, dopamine, ascorbic acid, caffeine, acetylsalicylic acid, tartrazine, sunset yellow, allure red, rutin, morin and metal ions. Finally, the novelty and usefulness of the composite were evaluated to quantify PCM in pharmaceutical dosage forms such as tablets, powders and syrups for children.

Three-dimensional porous self-assembled chestnut-like nickel-cobalt oxide structure as an electrochemical sensor for sensitive detection of hydrazine in water samples

Three-dimensional NiCo₂O₄ is a kind of superior sensing material owing to its high electron transfer capability, large available surface area and numbers of active sites. In this work, NiCo₂O₄ of the three-dimensional chestnut-like structure were easily achieved through a one step hydrothermal process. Afterwards, the morphology and structure were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). Based on the three-dimensional porous chestnut-like NiCo₂O₄, an electrochemical sensor for hydrazine (N₂H₄) detection is fabricated. This electrochemical platform can realize good selectivity, excellent stability, high sensitivity (∼2154.4 μA mM^-1 cm^-2), and low detection limit (0.3 μM), as well as a wide linear range from 1 μM to 1096 μM. The synergistic effect of nickel-cobalt in such mixed transition metal oxides which Co in Co₃O₄ is partially replaced by Ni are beneficial for enhancing sensing properties. This study proves that three-dimensional porous chestnut-like NiCo₂O₄ is electrochemically active for catalytic performance which is particular and promising material for good application in the practical detection of N₂H₄.

Ultrafine Pt–Ni bimetallic nanoparticles anchored on reduced graphene oxide nanocomposites for boosting electrochemical detection of dopamine in biological samples

The present report demonstrates the development of a Pt–Ni/rGO composite electrochemical sensor for the detection of dopamine.