Characterization of a macroporous epoxy-polymer based resin for the ion-exchange chromatography of therapeutic proteins

This study investigated the adsorption capacity and mass transfer properties of a novel macroporous epoxy-polymer-based anion-exchanger, MPR Q, for the efficient separation of therapeutic proteins. MPR Q resin was prepared by phase separation based on spinodal decomposition followed by dextran grafting and ligand conjugation. Under static conditions, MPR Q exhibited a binding capacity of 49.8 mg-IgG/cm³-resin at pH 10, whereas the fastest adsorption was observed among the anion-exchanger resins tested. Inverse size-exclusion chromatography (iSEC) experiments revealed that the apparent pore diameter of MPR Q was approximately 90 nm, which was sufficiently large for the penetration of human IgG and bovine IgM. Moreover, the reduced height equivalent to a theoretical plate, h, of human IgG, determined using the linear gradient elution method was 65.8 and was not significantly changed in the range of linear velocities from 20.37 to 50.93 cm/min. The dynamic binding capacity at 10% breakthrough of MPR Q, determined by frontal analysis, exhibited a capacity of 43.8 mg/cm³ at 5.09 cm/min and 58% of DBC_10% was maintained even though the linear velocity was increased to 50.93 cm/min. Furthermore, a resolution for separation of IgG and BSA by MPR Q was 1.06 at 5.09 cm/min, while it was higher than that for the conventional resin at all linear velocities from 5.09 cm/min to 50.93 cm/min. Thus, it was suggested that the MPR Q developed in this study is a promising resin that can efficiently separate large biomacromolecules such as human IgG at higher velocities.

Interfacial Structure Control and Three-Dimensional X-ray Imaging of an Epoxy Monolith Bonding System with Surface Modification

A monolith bonding system has a high reliability for dissimilar material bonding. The epoxy monolith layer fabricated on a substrate guarantees bond strength by the anchor effect, regardless of the compatibility of the used materials. Designing a high-performance monolith bonding system requires the suppression of an interfacial failure between the monolith and the substrate. In this study, silane and phosphine coupling agents containing amino and epoxy groups were used to construct a robust interfacial structure between the monolith and the substrates such as glass and metals. The internal and interfacial monolith structures were characterized by three-dimensional X-ray imaging as a nondestructive observation method in addition to the scanning electron microscopy of the sample cross sections. The modification of the substrate-monolith interface using the coupling agents improved the strength of dissimilar material bonding of the glass and metal substrates in combination with thermoplastic resins such as poly(ethylene terephthalate) and polycarbonate bisphenol-A.

Well-defined monolith morphology regulates cell adhesion and its functions

Hydrophilic epoxy resin-based monoliths were employed as cell culture substrates. The monoliths were made of a porous material with a bicontinuous structure that consisted of a porous channel and a resin skeleton. Monolith disks were prepared with a skinless surface through polymerization-induced spinodal decomposition-type phase separation. The pore sizes, which were well controlled by the polymerization temperature, ranged from 70 to 380 nm. The quantity of protein adsorbed per unit area and the early-stage adhesion of HepG2 cells on the monolith substrates were independent of pore size, meaning they were not affected by surface topology. Long-term cell adhesion, as indicated by adherent cell number and shape, as well as liver-specific gene expression were significantly affected by pore size. In terms of cell shape, number, and gene expression, pores of approximately 200 nm were most suitable for HepG2 cell growth. These results highlight the importance of monolith morphology for use as a cell culture substrate. The well-controlled morphology demonstrated in this work indicates monoliths are capable of supporting growth for various types of cells in a range of applications.

Iodine-mediated reversible-deactivation radical polymerization: a powerful strategy for polymer synthesis

In this review, the recent progress in iodine-mediated reversible-deactivation radical polymerization (RDRP) is highlighted.

LED-induced controlled radical polymerization with an in situ bromine–iodine transformation and block polymerization combined with ring-opening polymerization using one organocatalyst

Organocatalysts were employed in LED-induced controlled radical polymerization, sequentially combined with ring-opening polymerization to obtain copolymers using one organocatalyst.

Dissimilar Materials Bonding Using Epoxy Monolith

The epoxy monolith with a highly porous structure is fabricated by the thermal curing of 2,2-bis(4-glycidyloxyphenyl)propane and 4,4'-methylenebis(cyclohexylamine) in the presence of poly(ethylene glycol) as the porogen via polymerization-induced phase separation. In this study, we demonstrated a new type of dissimilar material bonding method for various polymers and metals coated with the epoxy monolith. On the basis of scanning electron microscopy (SEM) observations, the pore size and number of epoxy monoliths were evaluated to be 1.1-114 μm and 8.7-48 200 mm^-2, respectively, depending on the ratio of the epoxy resin and cross-linking agent used for the monolith fabrication. Various kinds of thermoplastics, such as polyethylene, polypropylene, polyoxymethylene, acrylonitrile-butadiene-styrene copolymer, polycarbonate bisphenol-A, and poly(ethylene terephthalate), were bonded to the monolith-modified metal plates by thermal welding. The bond strength for the single lap-shear tensile test of stainless steel and copper plates with the thermoplastics was in the range of 1.2-7.5 MPa, which was greater than the bond strength value for each bonding system without monolith modification. The SEM observation of fractured test pieces directly confirmed an anchor effect on this bonding system. The elongated deformation of the plastics that filled in the pores of the epoxy monolith, was observed. It was concluded that the bond strength significantly depended on the intrinsic strength of the used thermoplastics. The epoxy monolith bonding of hard plastics, such as polystyrene and poly(methyl methacrylate), was performed by the additional use of adhesives, solvents, and a reactive monomer. The epoxy monolith sheets were also successfully fabricated and applied to dissimilar material bonding.