Advances in Nanohybrid Membranes for Dye Reduction: A Comprehensive Review

Separating valuable materials such as dyes from wastewater using membranes and returning them to the production line is a desirable environmental and economical procedure. However, sometimes, besides filtration, adsorption, and separation processes, pollutant destruction also can be suitable using photocatalytic membranes. The art of producing nanohybrid materials in contrast with nanocomposites encompasses nanomaterial synthesis as a new product with different properties from raw materials for nanohybrids versus the composition of nanomaterials for nanocomposites. According to the findings of this research, confirming proper synthesis of nanohybrid is one challenge that can be overcome by different analyses, other researchers' reports, and the theoretical assessment of physical or chemical reactions. The application of organic-inorganic nanomaterials and frameworks is another challenge that is discussed in the present work. According to the findings, Nanohybrid Membranes (NHMs) can achieve 100% decolorization, but cannot eliminate salts and dyes, although the removal efficiency is notable for some salts, especially divalent salts. Hydrophilicity, antifouling properties, flux, pressure, costs, usage frequency, and mechanical, chemical, and thermal stabilities of NHMs should be considered.

Investigation of the Photocatalytic Activity of Electrospun and Surface-Modified PAN/α-FeOOH Nanofibers for the Degradation of Hazardous Azo Dyes

Decoration of α-FeOOH nanorods over PAN nanofibers was performed using the electrospinning technique. The as-designed decorated nanofibers were characterized using various techniques such as wide-angle powder X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), Fourier transform infrared (FTIR) spectroscopy, UV-vis spectrophotometry (UV-vis), thermogravimetry analysis (TGA), N2 adsorption-desorption isotherm (BET), and X-ray photoelectron spectrometry (XPS). α-FeOOH NRs were decorated uniformly over PAN fibers, as observed from its morphological investigation, which shows novelty. 1D α-FeOOH nanorods with PAN nanofibers have not been studied for photocatalytic characteristics. No literature mentions that α-FeOOH nanorods coated in PAN NFs act as photocatalysts to degrade hazardous azo dyes. α-FeOOH nanorods on PAN NFs inhibit aggregation and increase dye binding, boosting photocatalytic performance. PAN/α-FeOOH NFs have a maximal specific surface area with a reduced bandgap than α-FeOOH NRs. PAN/α-FeOOH nanofibers showed excellent photocatalytic activity for the degradation of Trypan blue (TB) (120 min, 99.7%) and Eriochrome black T (EBT) dyes (160 min, 97.6%), respectively, under solar light irradiation. PAN/α-FeOOH NFs have the potential to be used in the degradation of azo dyes and the treatment of wastewater due to their low energy requirements and versatility.

Novel Mixed Matrix Membranes Based on Poly(vinylidene fluoride): Development, Characterization, Modeling

Membrane technology is an actively developing area of modern societies; with the help of high-performance membranes, it is possible to separate various mixtures for many industrial tasks. The objective of this study was to develop novel effective membranes based on poly(vinylidene fluoride) (PVDF) by its modification with various nanoparticles (TiO₂, Ag-TiO₂, GO-TiO₂, and MWCNT/TiO₂). Two types of membranes have been developed: dense membranes for pervaporation and porous membranes for ultrafiltration. The optimal content of nanoparticles in the PVDF matrix was selected: 0.3 wt% for porous membranes and 0.5 wt% for dense ones. The structural and physicochemical properties of the developed membranes were studied using FTIR spectroscopy, thermogravimetric analysis, scanning electron and atomic force microscopies, and measuring of contact angles. In addition, the molecular dynamics simulation of PVDF and the TiO₂ system was applied. The transport properties and cleaning ability under ultraviolet irradiation of porous membranes were studied by ultrafiltration of a bovine serum albumin solution. The transport properties of dense membranes were tested in pervaporation separation of a water/isopropanol mixture. It was found that membranes with the optimal transport properties are as follows: the dense membrane modified with 0.5 wt% GO-TiO₂ and the porous membrane modified with 0.3 wt% MWCNT/TiO₂ and Ag-TiO₂.

Fabrication and Application of Halloysite Nanotube-Embedded Photocatalytic Nanofibers with Antibacterial Properties

With decreasing indoor air quality, increased time spent at indoors, and especially with the COVID-19 pandemic, the development of new materials for bacteria and viruses has become even more important. Less material consumption due to the electrospinning process, the easy availability/affordability of the halloysite nanotube (HNT), and the antibacterial effect of both TiO₂ and ZnO nanoparticles make the study even more interesting. HNTs have attracted research attention in recent years due to their low cost, high mechanical strength, natural and environmentally friendly structure, and non-toxicity to human health and ecosystem. In this study, HNT-embedded composite nanofiber filters were fabricated as filter materials using the electrospinning method. Photocatalysts (TiO₂ and ZnO) were incorporated into the composite nanofibers by the electrospraying method. The results showed that the combination of both HNT/TiO₂ and HNT/ZnO additives was successfully integrated into the filter structure. The effect of embedding the HNT and spraying photocatalysts enables the fabrication of composite filters with lower pressure drop, high filtration efficiency, improved mechanical properties, and high antibacterial properties against Escherichia coli, making the nanofibers suitable and promising for face masks and air filter materials.

Prospects of Polymeric Nanocomposite Membranes for Water Purification and Scalability and their Health and Environmental Impacts: A Review

Water shortage is a major worldwide issue. Filtration using genuine polymeric membranes demonstrates excellent pollutant separation capabilities; however, polymeric membranes have restricted uses. Nanocomposite membranes, which are produced by integrating nanofillers into polymeric membrane matrices, may increase filtration. Carbon-based nanoparticles and metal/metal oxide nanoparticles have received the greatest attention. We evaluate the antifouling and permeability performance of nanocomposite membranes and their physical and chemical characteristics and compare nanocomposite membranes to bare membranes. Because of the antibacterial characteristics of nanoparticles and the decreased roughness of the membrane, nanocomposite membranes often have greater antifouling properties. They also have better permeability because of the increased porosity and narrower pore size distribution caused by nanofillers. The concentration of nanofillers affects membrane performance, and the appropriate concentration is determined by both the nanoparticles' characteristics and the membrane's composition. Higher nanofiller concentrations than the recommended value result in deficient performance owing to nanoparticle aggregation. Despite substantial studies into nanocomposite membrane manufacturing, most past efforts have been restricted to the laboratory scale, and the long-term membrane durability after nanofiller leakage has not been thoroughly examined.

Effect of Polymer Concentration on the Photocatalytic Membrane Performance of PAN/TiO2/CNT Nanofiber for Methylene Blue Removal through Cross-Flow Membrane Reactor

A photocatalytic membrane combining photocatalyst and membrane technology based on polyacrylonitrile (PAN) and TiO2/CNT has been developed. Such combination is to overcome fouling formation on the membrane, thus prolonging the membrane lifetime and enhancing the efficiency on the waste treatment. PAN nanofiber was prepared by electrospinning method. The precursor solution was dissolved PAN and dispersed TiO2/CNT in N,N-Dimethylformamide (DMF). PAN concentration in the precursor solution was varied at 4.5, 5.5, 6.5, 7.5, and 8.5%. The effect of PAN concentration on the fiber morphology and pore size was discussed. The performance of the resulted membrane on methylene blue (MB) removal was also investigated on a cross-flow system. SEM images of the resulted membrane identified that PAN nanofiber was successfully fabricated with random orientation. The PAN 6.5% showed the highest diffraction intensity of the anatase crystalline phase of TiO2. The additions of CNT and TiO2 lead to the formation of a cluster of beads as confirmed by TEM. Increasing the concentration of PAN increased the fiber diameter from 206 to 506 nm, slightly decreased the surface area and pore size, respectively, from 32.739 to 21.077 m2.g−1 and from 6.38 to 4.75 nm. The PAN/TiO2/CNT nanofibers show type IV of the adsorption-desorption N2 isotherms with the H1 hysteresis loops. Membrane PAN/TiO2/CNT at PAN concentration of 6.5% shows the optimum performance on the MB color removal by maintaining the percentage of rejection (%R) at 90% for 240 min and permeability of 750 LMH. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Ag nanoparticles immobilized sulfonated polyethersulfone/polyethersulfone electrospun nanofiber membrane for the removal of heavy metals

In this work, Eucommia ulmoides leaf extract (EUOLstabilized silver nanoparticles (EUOL@AgNPs) incorporated sulfonated polyether sulfone (SPES)/polyethersulfone (PES) electrospun nanofiber membranes (SP ENMs) were prepared by electrospinning, and they were studied for the removal of lead (Pb(II)) and cadmium (Cd(II)) ions from aqueous solutions. The SP ENMs with various EUOL@AgNPs loadings were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscope, thermo-gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and contact angle (CA) measurements. The adsorption studies showed that the adsorption of Cd(II) and Pb(II) was rapid, achieved equilibrium within 40 min and 60 min, respectively and fitted with non-linear pseudo-second-order (PSO) kinetics model. For Cd(II) and Pb(II), the Freundlich model described the adsorption isotherm better than the Langmuir isotherm model. The maximum adsorption capacity for Cd(II) and Pb(II) was 625 and 370.37 mg g⁻¹ respectively at neutral pH. Coexisting anions of fluoride, chloride, and nitrate had a negligible influence on Cd(II) removal than the Pb(II). On the other hand, the presence of silicate and phosphate considerably affected Cd(II) and Pb(II) adsorption. The recyclability, regeneration, and reusability of the fabricated EUOL@AgNPs-SP ENMs were studied and they retained their high adsorption capacity up to five cycles. The DFT measurements revealed that SP-5 ENMs exhibited the highest adsorption selectivity for Cd(II) and the measured binding energies for Cd(II), Pb(II), are 219.35 and 206.26 kcal mol⁻¹, respectively. The developed ENM adsorbent may find application for the removal of heavy metals from water.

A comprehensive review on electrospun nanohybrid membranes for wastewater treatment

Electrospinning, being a versatile and straightforward method to produce nanofiber membranes, has shown significant advancement in recent years. On account of the unique properties such as high surface area, high porosity, mechanical strength, and controllable surface morphologies, electrospun nanofiber membranes have been found to have a great potential in many disciplines. Pure electrospun fiber mats modified with different techniques of surface modification and additive incorporation have exhibited enhanced properties compared to traditional membranes and are even better than the as-prepared electrospun membranes. In this review, we have summarized recently developed electrospun nanohybrids fabricated by the incorporation of functional specific nanosized additives to be used in various water remediation membrane techniques. The adsorption, filtration, photocatalytic, and bactericidal capabilities of the hybrid membranes in removing common major water pollutants such as metal ions, dyes, oils, and biological pollutants have been discussed. Finally, an outlook on the future research pathways to fill the gaps existing in water remediation have been suggested.

Photocatalytic Nanofiber Membranes for the Degradation of Micropollutants and Their Antimicrobial Activity: Recent Advances and Future Prospects

This review paper systematically evaluates current progress on the development and performance of photocatalytic nanofiber membranes often used in the removal of micropollutants from water systems. It is demonstrated that nanofiber membranes serve as excellent support materials for photocatalytic nanoparticles, leading to nanofiber membranes with enhanced optical properties, as well as improved recovery, recyclability, and reusability. The tremendous performance of photocatalytic membranes is attributed to the photogenerated reactive oxygen species such as hydroxyl radicals, singlet oxygen, and superoxide anion radicals introduced by catalytic nanoparticles such as TiO₂ and ZnO upon light irradiation. Hydroxyl radicals are the most reactive species responsible for most of the photodegradation processes of these unwanted pollutants. The review also demonstrates that self-cleaning and antimicrobial nanofiber membranes are useful in the removal of microbial species in water. These unique materials are also applicable in other fields such as wound dressing since the membrane allows for oxygen flow in wounds to heal while antimicrobial agents protect wounds against infections. It is demonstrated that antimicrobial activities against bacteria and photocatalytic degradation of micropollutants significantly reduce membrane fouling. Therefore, the review demonstrates that electrospun photocatalytic nanofiber membranes with antimicrobial activity form efficient cost-effective multifunctional composite materials for the removal of unwanted species in water and for use in various other applications such as filtration, adsorption and electrocatalysis.

Nanofibrous Photocatalytic Membranes Based on Tailored Anisotropic Gold/Ceria Nanoparticles

The combination of plasmonic nanoparticles with semiconductor photocatalysts is a good strategy for synthesizing highly efficient photocatalysts. Such binary nanoparticles have demonstrated enhanced catalytic activity in comparison to either plasmonic catalysts or semiconductor catalysts. However, problematic recovery and limited long-term colloidal stability of those nanoparticles in suspension limit their wide use in catalysis. To palliate to such limitations, we embedded binary nanoparticles in polymer fibers to design photocatalytic membranes. First, we used the selective over-growth of crystalline cerium oxide on the gold nanoparticle template with distinct shapes. Gold nanospheres, gold nanorods, and gold nanotriangles were used as the template for the growth of the cerium oxide domains. Then, the resulting nanoparticles were used to catalyze model reactions in suspensions. The gold nanoparticles covered with patches of cerium oxide outperformed the fully covered and naked nanoparticles in terms of catalytic efficiency. Finally, the most efficient binary nanostructures were successfully embedded in nanofibrous membranes by colloidal electrospinning and used in water remediation experiments in a flow-through reactor.

Enhanced visible-light photodegradation of fluoroquinolone-based antibiotics and E. coli growth inhibition using Ag-TiO2 nanoparticles

Antibiotics in wastewater represent a growing and worrying menace for environmental and human health fostering the spread of antimicrobial resistance. Titanium dioxide (TiO₂) is a well-studied and well-performing photocatalyst for wastewater treatment. However, it presents drawbacks linked with the high energy needed for its activation and the fast electron–hole pair recombination. In this work, TiO₂ nanoparticles were decorated with Ag nanoparticles by a facile photochemical reduction method to obtain an increased photocatalytic response under visible light. Although similar materials have been reported, we advanced this field by performing a study of the photocatalytic mechanism for Ag–TiO₂ nanoparticles (Ag–TiO₂ NPs) under visible light taking in consideration also the rutile phase of the TiO₂ nanoparticles. Moreover, we examined the Ag–TiO₂ NPs photocatalytic performance against two antibiotics from the same family. The obtained Ag–TiO₂ NPs were fully characterised. The results showed that Ag NPs (average size: 23.9 ± 18.3 nm) were homogeneously dispersed on the TiO₂ surface and the photo-response of the Ag–TiO₂ NPs was greatly enhanced in the visible light region when compared to TiO₂ P25. Hence, the obtained Ag–TiO₂ NPs showed excellent photocatalytic degradation efficiency towards the two fluoroquinolone-based antibiotics ciprofloxacin (92%) and norfloxacin (94%) after 240 min of visible light irradiation, demonstrating a possible application of these particles in wastewater treatment. In addition, it was also proved that, after five Ag–TiO₂ NPs re-utilisations in consecutive ciprofloxacin photodegradation reactions, only a photocatalytic efficiency drop of 8% was observed. Scavengers experiments demonstrated that the photocatalytic mechanism of ciprofloxacin degradation in the presence of Ag–TiO₂ NPs is mainly driven by holes and ˙OH radicals, and that the rutile phase in the system plays a crucial role. Finally, Ag–TiO₂ NPs showed also antibacterial activity towards Escherichia coli (E. coli) opening the avenue for a possible use of this material in hospital wastewater treatment.

Ag nanoparticles decorated-TiO₂ P25 are a viable alternative for the degradation, through a rutile-mediated mechanism, of fluoroquinolone-based antibiotics under visible light irradiation and, at the same time, for bacteria inactivation in water.

Electrospun-based TiO2 nanofibers for organic pollutant photodegradation: a comprehensive review

Titanium dioxide (TiO2) is commonly used as a photocatalyst in the removal of organic pollutants. However, weaknesses of TiO2 such as fast charge recombination and low visible light usage limit its industrial application. Furthermore, photocatalysts that are lost during the treatment of pollutants create the problem of secondary pollutants. Electrospun-based TiO2 fiber is a promising alternative to immobilize TiO2 and to improve its performance in photodegradation. Some strategies have been employed in fabricating the photocatalytic fibers by producing hollow fibers, porous fibers, composite TiO2 with magnetic materials, graphene oxide, as well as doping TiO2 with metal. The modification of TiO2 can improve the absorption of TiO2 to the visible light area, act as an electron acceptor, provide large surface area, and promote the phase transformation of TiO2. The improvement of TiO2 properties can enhance carrier transfer rate which reduces the recombination and promotes the generation of radicals that potentially degrade organic pollutants. The recyclability of fibers, calcination effect, photocatalytic reactors used, operation parameters involved in photodegradation as well as the commercialization potential of TiO2 fibers are also discussed in this review.

Sacrifice Template Strategy to the Fabrication of a Self-Cleaning Nanofibrous Membrane for Efficient Crude Oil-in-Water Emulsion Separation with High Flux

The superhydrophilic/underwater superoleophobic membrane materials have attracted considerable attention in oil/water separation. However, most materials are extremely susceptible to pollution during oil-water separation, which drastically restricts their widespread applications. Herein, a momordica-charantia-like nanofibrous membrane (MCNM) with underwater superoleophobic performance was fabricated through a sacrifice template strategy by the electrospinning solution of zeolitic imidazolate framework-8 (ZIF-8) and polyacrylonitrile particles. The opened voids and wrinkles left after removing the template of nanocrystals ZIF-8 not only increased the porosity and roughness of the as-prepared fibrous membrane but also tremendously improved the underwater superoleophobicity. Therefore, the as-prepared MCNM showed excellent self-cleaning performance toward crude oil under water, avoiding the decrease of the separation efficiency and flux caused by membrane fouling during oil-water separation. Meanwhile, the separation efficiency of various surfactant-stabilized oil-in-water emulsions was higher than 99.6% with a flux up to 1580 ± 30 L m^-2 h^-1 solely driven by gravity. Moreover, no obvious wrinkles and cracks were observed on the resulted nanofibrous membrane after the sand impact and bent testing. More importantly, the as-prepared MCNM still maintained exceptional underwater superoleophobicity in harsh environment (3.5 wt % NaCl, 4 M HCl, 50 °C hot water) even after ultrasound for 1 h. The robust mechanical and chemical stability makes the antifouling MCNM exhibit tremendous potential for practical applications in dealing with oily wastewater in the future.

Trimetallic composite nanofibers for antibacterial and photocatalytic dye degradation of mixed dye water

Membrane technology is an advanced approach to making a healthier and cleaner environment. Using such catalytic membrane technology to get clean, usable water by removal of dye impurities as well as pathogenic microbes is the main goal behind the research work. Here, we present the synthesis and efficacy study of polymethyl methacrylate (PMMA)-based Ag/ZnO/TiO₂ trimetallic bifunctional nanofibers with antibacterial and photocatalytic activity. The nanofibers have been proven to be effective for the degradation of methylene blue (MB 93.4%), rhodamine B (Rh 34.6%), auramine-O (Au 65.0%) and fuchsin basic (FB 69.8%) dyes individually within 90 min in daylight. The study is further extended in abating a mixture of these dyes from contaminated water using composite nanofibers. Also, in the case of a mixture of these dyes (3 ppm each), nanofibers show dye degradation efficiency (DDE) of 90.9% (MB), 62.4% (Au) and 90.3% (FB and Rh) in 60 min. The role of Ag nanoparticles with a synergic photocatalytic effect on ZnO and TiO₂ is also demonstrated. Also, PMMA/ZnO/TiO₂ composite fiber membrane in synergy with silver particles shows better antibacterial activity against Gram-negative bacteria E. coli, making PMMA/Ag/ZnO/TiO₂ fibers a promising candidate in water purification.

Bioinspired design of underwater superoleophobic Poly(N-isopropylacrylamide)/ polyacrylonitrile/TiO2 nanofibrous membranes for highly efficient oil/water separation and photocatalysis

Inspired by fish scales, this study prepares a thermo-responsive underwater oleophobic PNIPAM/PAN/TiO₂ nanofibrous membranes by traditional electrospinning technique using poly-N-isopropylacrylamide (PNIPAM) and polyacrylonitrile (PAN). Thermal properties, mechanical properties, surface chemical composition, wettability, photocatalysis, and oil/water separation of PNIPAM/PAN/TiO₂ membrane are explored compared to pure PNIPAM membrane. Result reveals that PAN/TiO₂ compounds make PNIPAM membrane with a smaller fiber diameter of 141 nm and high tensile stress of 7.4 MPa, and also decompose 98% of rhodamine B after UV light radiation. This bioinspired design structure endows the membrane with superhydrophilicity with a low water contact angle, and underwater superoleophobicity with a high oil contact angle of 157° (petroleum ether) and 151° (dichloromethane). This membrane can efficiency separate oil/water mixture with a high separation efficiency. Moreover, the resultant PNIPAM/PAN/TiO₂ membrane has the bionic fish scale structure, and has wettability respond at lower critical solution temperature making the water flux decreased from 10013 ± 367 L m^-2·h^-1 to 7713 ± 324 L m^-2·h^-1, and thus has a potential to be used in purification of reclaimed water and separation of oil from water.

Critical Issues and Guidelines to Improve the Performance of Photocatalytic Polymeric Membranes

Photocatalytic membrane reactors (PMR), with immobilized photocatalysts, play an important role in process intensification strategies; this approach offers a simple solution to the typical catalyst recovery problem of photocatalytic processes and, by simultaneous filtration and photocatalysis of the aqueous streams, facilitates clean water production in a single unit. The synthesis of polymer photocatalytic membranes has been widely explored, while studies focused on ceramic photocatalytic membranes represent a minority. However, previous reports have identified that the successful synthesis of polymeric photocatalytic membranes still faces certain challenges that demand further research, e.g., (i) reduced photocatalytic activity, (ii) photocatalyst stability, and (iii) membrane aging, to achieve technological competitiveness with respect to suspended photocatalytic systems. The novelty of this review is to go a step further to preceding literature by first, critically analyzing the factors behind these major limitations and second, establishing useful guidelines. This information will help researchers in the field in the selection of the membrane materials and synthesis methodology for a better performance of polymeric photocatalytic membranes with targeted functionality; special attention is focused on factors affecting membrane aging and photocatalyst stability.

Electrospun Bilayer PAN/Chitosan Nanofiber Membranes Incorporated with Metal Oxide Nanoparticles for Heavy Metal Ion Adsorption

Bilayer nanofiber membranes with enhanced adsorption and mechanical properties were produced by combining a layer of polyacrylonitrile (PAN) functionalized with metal oxides (MO) of ZnO or TiO2 with a layer of chitosan (CS) via consecutive electrospinning. The adsorption properties of the bilayer PAN/MO–CS nanofiber membranes against lead (Pb(II)) and cadmium (Cd(II)) ions were investigated, including the effects of the solution pH, initial ion concentrations, and interaction time. The integration of a CS layer into PAN/MO nanofibers increased the adsorption capacity of lead by 102% and cadmium by 405%, compared to PAN/MO single layer. The nonlinear optimization method showed that the pseudo-second-order kinetic model and Langmuir isotherm equation better described the adsorption results. More importantly, the incorporation of a supportive CS nanofiber layer enhanced the tensile strength of PAN/MO–CS bilayer by approximately 68% compared to the PAN/MO single layer, owing to the strong interaction between the fibers at the interface of the two layers.

Composites Based on Nanoparticle and Pan Electrospun Nanofiber Membranes for Air Filtration and Bacterial Removal

Often, solid matter is separated from particle-laden flow streams using electrospun filters due to their high specific surface area, good ability to capture aerial particulate matter, and low material costs. Moreover, electrospinning allows incorporating nanoparticles to improve the filter's air filtration efficiency and bacterial removal. Therefore, a new, improved polyacrylonitrile (PAN) nanofibers membrane that could be used to remove air pollutants and also with antibacterial activity was developed. We engineered three different filters that are characterized by the different particles embedded in the PAN nanofibers: titanium dioxide (TiO2), zinc oxide (ZnO), and silver (Ag). Then, their filtration performance was assessed by quantifying the filtration of sodium chloride (NaCl) aerosol particles of 9 to 300 nm in diameter using a scanning mobility particle sizer. The TiO2_F filter displayed the smallest fiber diameter and the highest filtration efficiency (≈100%). Conversely, the Ag_F filter showed the highest quality factor (≈0.06 Pa-1) because of the lower air pressure drop. The resulting Ag_F nanofibers displayed a very good antibacterial activity using an Escherichia coli suspension (108 CFU/mL). Moreover, the quality factor of these membranes was higher than that of the commercially available nanofiber membrane for air filtration.

Fabrication and Characterization of Modified Graphene Oxide/PAN Hybrid Nanofiber Membrane

In this study, a series of novel modified graphene oxide (MGO)/polyacrylonitrile (PAN) hybrid nanofiber membranes were fabricated by electrospinning a PAN solution containing up to 1.0 wt.% MGO. The GO was initially prepared by a time-saving improved Hummer’s method. Subsequently, the formation of GO was confirmed by scanning electron microscopy (SEM), AFM, Fourier-transform infrared spectroscopy (FT–IR), and Raman spectroscopy. This study also prepared the modified GO with polydiallyldimethylammonium chloride (GP) by using a simple surface post-treatment method to improve its dispersion. Varying amounts of GP were incorporated into PAN nanofibers for the better properties of GP/PAN nanofibers, such as hydrophilicity, mechanical properties, and so on. The resulting GP/PAN hybrid nanofiber membranes were characterized by SEM, FTIR, contact angle, and thermal and mechanical properties. These results showed that the hydrophilic and mechanical properties of GP/PAN hybrid nanofiber membranes were dramatically improved, i.e., 50% improvement for hydrophilicity and 3–4 times higher strength for mechanical property, which indicated the possibility for water treatment application. In addition, the notably improved thermal stability results showed that the hybrid nanofiber membranes could also be a potential candidate for the secondary battery separator.

One-pot synthesis of catalytic molybdenum based nanocomposite nano-fiber membranes for aerosol air remediation

The development of fibrous air filters exhibiting high air filtration efficiency, low energy consumption, and self-cleaning properties is a critical challenge to generate the next generation of resilient air filtration systems. Nano-fibrous mats typically exhibit higher particle capture efficiency but may also lead to higher airflow resistance compared to macro-fibrous materials due to their tighter structure. In this paper, novel catalytic membranes mats were fabricated through a one-pot synthesis from ammonium tetrathiomolybdate (ATTM) doped poly(acrylonitrile) (PAN) nanofibers for sub-micron diameter aerosol particle removal. The presence of ATTM as a dopant in conjunction with a PAN polymeric matrix was found to not only enhance the air filtration performance by increasing aerosol particle removal down to 300 nm, but also increase the photocatalytic properties of the PAN material. The enhanced separation properties compared to bare polymeric PAN nanofibrous membranes were attributed to surface nanotexturation of the fibers, leading to protrusions and pores across the nano-fiber structures, thus leading to more permeable and lightweight membranes with higher particle capture capacities. The samples were benchmarked against commercial glass fiber air filters and found to offer higher filtration efficiency, lower pressure drop, and higher quality factor than the commercial filters. Specifically, the quality factors of the catalytic nano-fiber membranes were found to be up to four times higher than that of the benchmarked commercial air filters for PM_2.5 particles, while two times higher for 300 nm sized contaminants. The presence of the ATTM across the PAN matrix was also found to enhance the photocatalytic activity of the membranes by up to 130% compared to the bare PAN reference nanofibers. This novel strategy opens avenues to engineering advanced multifunctional catalytic membranes, to capture toxic particulate matter from air while offering self-cleaning properties when exposed to sunlight.

Synthesis, Characterization and Photocatalytic Activity of Nanocrystalline First Transition-Metal (Ti, Mn, Co, Ni and Zn) Oxisde Nanofibers by Electrospinning

In this work, five nanocrystalline first transition-metal (Ti, Mn, Co, Ni and Zn) oxide nanofibers were prepared by electrospinning and controlled calcination. The morphology, crystal structure, pore size distribution and specific surface area were systematically studied by scanning electron microscope (SEM), transmission electron microscope (TEM), surface and pore analysis, and thermo gravimetric analyzer (TGA). The results reveal that the obtained nanofibers have a continuously twisted three-dimensional scaffold structure and are composed of neat nanocrystals with a necklace-like arrangement. All the samples possess high specific surface areas, which follow the order of NiO nanofiber (393.645 m2/g) > TiO2 nanofiber (121.445 m2/g) > ZnO nanofiber (57.219 m2/g) > Co3O4 nanofiber (52.717 m2/g) > Mn2O3 nanofiber (18.600 m2/g). Moreover, the photocatalytic degradation of methylene blue (MB) in aqueous solution was investigated in detail by employing the five kinds of metal oxide nanofibers as photocatalysts under ultraviolet (UV) irradiation separately. The results show that ZnO, TiO2 and NiO nanofibers exhibit excellent photocatalytic efficiency and high cycling ability to MB, which may be ascribed to unique porous structures and the highly efficient separation of photogenerated electron-hole pairs. In brief, this paper aims to provide a feasible approach to achieve five first transition-metal oxide nanofibers with excellent performance, which is important for practical applications.