Surface characterization of thin-film composite membranes using contact angle technique: Review of quantification strategies and applications

Thin-film composite (TFC) membranes are the most widely used membranes for low-cost and energy-efficient water desalination processes. Proper control over the three influential surface parameters, namely wettability, roughness, and surface charge, is vital in optimizing the TFC membrane surface and permeation properties. More specifically, the surface properties of TFC membranes are often tailored by incorporating novel special wettability materials to increase hydrophilicity and tune surface physicochemical heterogeneity. These essential parameters affect the membrane permeability and antifouling properties. The membrane surface characterization protocols employed to date are rather controversial, and there is no general agreement about the metrics used to evaluate the surface hydrophilicity and physicochemical heterogeneity. In this review, we surveyed and critically evaluated the process that emerged for understanding the membrane surface properties using the simple and economical contact angle analysis technique. Contact angle analysis allows the estimation of surface wettability, surface free energy, surface charge, oleophobicity, contact angle hysteresis, and free energy of interaction; all coordinatively influence the membrane permeation and fouling properties. This review will provide insights into simplifying the evaluation of membrane properties by contact angle analysis that will ultimately expedite the membrane development process by reducing the time and expenses required for the characterization to confirm the success and the impact of any modification.

Three-Stage Membrane Treatment of Wastewater from Biodiesel Production-Preliminary Research

As biodiesel production as renewable fuel increases, so does the amount of wastewater resulting from this technology. Wastewater is generated during the so-called biodiesel washing, i.e., washing out glycerol and methanol with water. The purified biodiesel must meet international standards, such as EN 14214 or the American ASTM D6751 standard. To fully say that biodiesel technology is environmentally friendly, the amount of wastewater should be minimized. It is also desirable that the purified water can be recycled to the technology. For this purpose, wastewater pre-treated by flotation, during which mainly oils are removed, was subjected to three-stage membrane separation. For each of the stages, the membrane was selected and characterized in terms of its separation capacity and stream stability. Starting with microfiltration, which was mainly aimed at reducing turbidity, affects the permeate flux in the following steps. Then, ultrafiltration and nanofiltration membranes were selected. These membranes were aimed at reducing the concentration of inorganic and organic substances. Consequently the cascade was composed of: MF-0.45 µm, UF-150 kDa, and NF-characterized by an 80% degree of desalination. The final permeate has a salt concentration of less than 0.15 g/L and can be reused in biodiesel technology.

Hollow-Fiber RO Membranes Fabricated via Adsorption of Low-Charge Poly(vinyl alcohol) Copolymers

We report a new type of alkaline-stable hollow-fiber reverse osmosis (RO) membrane with an outside-in configuration that was established via adsorption of positively charged poly(vinyl alcohol) copolymers containing a small amount of quaternary ammonium moieties. Anionic sulfonated poly(arylene ether sulfone nitrile) hollow-fiber membranes were utilized as a substrate upon which the cationic copolymer layer was self-organized via electrostatic interaction. While the adsorption of the low-charge copolymer on the membrane support proceeded in a Layer-by-Layer (LbL) fashion, it was found that the adsorbed amount by one immersion step was enough to form a defect-free separation layer with a thickness of around 20 nm after cross-linking of vinyl alcohol units with glutaraldehyde. The resultant hollow-fiber membrane showed excellent desalination performances (NaCl rejection of 98.3% at 5 bar and 1500 mg/L), which is comparable with commercial low-pressure polyamide RO membranes, as well as good alkaline resistance. The separation performance could be restored by repeating the LbL treatment after alkaline degradation. Such features of LbL membranes may contribute to extending RO membrane lifetimes.

Naturally Extracted Hydrophobic Solvent and Self-Assembly in Interfacial Polymerization

Pharmaceutical, chemical, and food industries are actively implementing membrane nanofiltration modules in their processes to separate valuable products and recover solvents. Interfacial polymerization (IP) is the most widely used method to produce thin-film composite membranes for nanofiltration and reverse osmosis processes. Although membrane processes are considered green and environmentally friendly, membrane fabrication has still to be further developed in such direction. For instance, the emission of volatile solvents during membrane production in the industry has to be carefully controlled for health reasons. Greener solvents are being proposed for phase-separation membrane manufacture. For the IP organic phase, the proposition of greener alternatives is in an early stage. In this work, we demonstrate the preparation of a high-performing composite membrane employing zero vapor pressure and naturally extracted oleic acid as the IP organic phase. Its long hydrophobic chain ensures intrinsic low volatility and acid monomer dissolution, while the polar head induces a unique self-assembly structure during the film formation. Membranes prepared by this technique were selective for small molecules with a molecular weight cutoff of 650 g mol^-1 and a high permeance of ∼57 L m^-2 h^-1 bar^-1.