1
|
Koppány F, Csomó KB, Varmuzsa EM, Bognár E, Pelyhe L, Nagy P, Kientzl I, Szabó D, Weszl M, Dobos G, Lenk S, Erdei G, Kiss G, Nagy L, Sréter A, Belik AA, Tóth Z, Vág J, Joób-Fancsaly Á, Németh Z. Enhancement of Hydrophilicity of Nano-Pitted TiO 2 Surface Using Phosphoric Acid Etching. NANOMATERIALS (BASEL, SWITZERLAND) 2023; 13:511. [PMID: 36770473 PMCID: PMC9919856 DOI: 10.3390/nano13030511] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 01/01/2023] [Revised: 01/17/2023] [Accepted: 01/25/2023] [Indexed: 06/18/2023]
Abstract
Our research group developed a novel nano-pitted (NP) TiO2 surface on grade 2 titanium that showed good mechanical, osteogenic, and antibacterial properties; however, it showed weak hydrophilicity. Our objective was to develop a surface treatment method to enhance the hydrophilicity of the NP TiO2 surface without the destruction of the nano-topography. The effects of dilute and concentrated orthophosphoric (H3PO4) and nitric acids were investigated on wettability using contact angle measurement. Optical profilometry and atomic force microscopy were used for surface roughness measurement. The chemical composition of the TiO2 surface and the oxidation state of Ti was investigated using X-ray photoelectron spectroscopy. The ccH3PO4 treatment significantly increased the wettability of the NP TiO2 surfaces (30°) compared to the untreated control (88°). The quantity of the absorbed phosphorus significantly increased following ccH3PO4 treatment compared to the control and caused the oxidation state of titanium to decrease (Ti4+ → Ti3+). Owing to its simplicity and robustness the presented surface treatment method may be utilized in the industrial-scale manufacturing of titanium implants.
Collapse
Affiliation(s)
- Ferenc Koppány
- Department of Oro-Maxillofacial Surgery and Stomatology, Semmelweis University, 1085 Budapest, Hungary
| | - Krisztián Benedek Csomó
- Department of Oro-Maxillofacial Surgery and Stomatology, Semmelweis University, 1085 Budapest, Hungary
| | - Edvárd Márton Varmuzsa
- Department of Oro-Maxillofacial Surgery and Stomatology, Semmelweis University, 1085 Budapest, Hungary
| | | | | | | | | | | | - Miklós Weszl
- Department of Translational Sciences, Semmelweis University, 1085 Budapest, Hungary
| | - Gábor Dobos
- Department of Atomic Physics, Institute of Physics, Budapest University of Technology and Economics, 1111 Budapest, Hungary
| | - Sándor Lenk
- Department of Atomic Physics, Institute of Physics, Budapest University of Technology and Economics, 1111 Budapest, Hungary
| | - Gábor Erdei
- Department of Atomic Physics, Institute of Physics, Budapest University of Technology and Economics, 1111 Budapest, Hungary
| | - Gábor Kiss
- Department of Atomic Physics, Institute of Physics, Budapest University of Technology and Economics, 1111 Budapest, Hungary
| | - Lilien Nagy
- Department of Prosthodontics, Semmelweis University, 1088 Budapest, Hungary
| | - Attila Sréter
- Faculty of Dentistry, Semmelweis University, 1085 Budapest, Hungary
| | | | - Zsuzsanna Tóth
- Department of Restorative Dentistry and Endodontics, Semmelweis University, 1088 Budapest, Hungary
| | - János Vág
- Department of Restorative Dentistry and Endodontics, Semmelweis University, 1088 Budapest, Hungary
| | - Árpád Joób-Fancsaly
- Department of Oro-Maxillofacial Surgery and Stomatology, Semmelweis University, 1085 Budapest, Hungary
| | - Zsolt Németh
- Department of Oro-Maxillofacial Surgery and Stomatology, Semmelweis University, 1085 Budapest, Hungary
| |
Collapse
|
2
|
Surgical Applications of Materials Engineered with Antimicrobial Properties. Bioengineering (Basel) 2022; 9:bioengineering9040138. [PMID: 35447700 PMCID: PMC9030825 DOI: 10.3390/bioengineering9040138] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/07/2022] [Revised: 03/17/2022] [Accepted: 03/24/2022] [Indexed: 02/06/2023] Open
Abstract
The infection of surgically placed implants is a problem that is both large in magnitude and that broadly affects nearly all surgical specialties. Implant-associated infections deleteriously affect patient quality-of-life and can lead to greater morbidity, mortality, and cost to the health care system. The impact of this problem has prompted extensive pre-clinical and clinical investigation into decreasing implant infection rates. More recently, antimicrobial approaches that modify or treat the implant directly have been of great interest. These approaches include antibacterial implant coatings (antifouling materials, antibiotics, metal ions, and antimicrobial peptides), antibacterial nanostructured implant surfaces, and antibiotic-releasing implants. This review provides a compendium of these approaches and the clinical applications and outcomes. In general, implant-specific modalities for reducing infections have been effective; however, most applications remain in the preclinical or early clinical stages.
Collapse
|
3
|
Ishantha Senevirathne SWMA, Hasan J, Mathew A, Jaggessar A, Yarlagadda PKDV. Trends in Bactericidal Nanostructured Surfaces: An Analytical Perspective. ACS APPLIED BIO MATERIALS 2021; 4:7626-7642. [PMID: 35006714 DOI: 10.1021/acsabm.1c00839] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/06/2023]
Abstract
Since the discovery of the bactericidal properties of cicada wing surfaces, there has been a surge in the number of studies involving antibacterial nanostructured surfaces (NSS). Studies show that there are many parameters (and thus, thousands of parameter combinations) that influence the bactericidal efficiency (BE) of these surfaces. Researchers attempted to correlate these parameters to BE but have so far been unsuccessful. This paper presents a meta-analysis and perspective on bactericidal NSS, aiming to identify trends and gaps in the literature and to provide insights for future research. We have attempted to synthesize data from a wide range of published studies and establish trends in the literature on bactericidal NSS. Numerous research gaps and findings based on correlations of various parameters are presented here, which will assist in the design of efficient bactericidal NSS and shape future research. Traditionally, it is accepted that BE of NSS depends on the bacterial Gram-stain type. However, this review found that factors beyond Gram-stain type are also influential. Furthermore, it is found that despite their higher BE, hydrophobic NSS are less commonly studied for their bactericidal effect. Interestingly, the impacts of surface hydrophobicity and roughness on the bactericidal effect were found to be influenced by a Gram-stain type of the tested bacteria. In addition, cell motility and shape influence BE, but research attention into these factors is lacking. It was found that hydrophobic NSS demonstrate more promising results than their hydrophilic counterparts; however, these surfaces have been overlooked. Confirming the common belief of the influence of nanofeature diameter on bactericidal property, this analysis shows the feature aspect ratio is also decisive. NSS fabricated on silicon substrates perform better than their titanium counterparts, and the success of these silicon structures maybe attributed to the fabrication processes. These insights benefit engineers and scientists alike in developing next-generation NSS.
Collapse
Affiliation(s)
| | - Jafar Hasan
- Centre for Biomedical Technologies, Queensland University of Technology, Brisbane, Queensland 4000, Australia
| | - Asha Mathew
- Centre for Biomedical Technologies, Queensland University of Technology, Brisbane, Queensland 4000, Australia
| | - Alka Jaggessar
- Centre for Biomedical Technologies, Queensland University of Technology, Brisbane, Queensland 4000, Australia
| | - Prasad K D V Yarlagadda
- Centre for Biomedical Technologies, Queensland University of Technology, Brisbane, Queensland 4000, Australia
| |
Collapse
|
4
|
Abdel-Karim AM, Fadlallah SA. Fabrication of titanium nanotubes array: phase structure, hydrophilic properties, and electrochemical behavior approach. J APPL ELECTROCHEM 2021. [DOI: 10.1007/s10800-021-01618-1] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/20/2022]
|
5
|
Mei S, Wang F, Hu X, Yang K, Xie D, Yang L, Wu Z, Wei J. Construction of a hierarchical micro & nanoporous surface for loading genistein on the composite of polyetheretherketone/tantalum pentoxide possessing antibacterial activity and accelerated osteointegration. Biomater Sci 2021; 9:167-185. [PMID: 33165465 DOI: 10.1039/d0bm01306d] [Citation(s) in RCA: 16] [Impact Index Per Article: 5.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/21/2022]
Abstract
Nanoporous tantalum pentoxide (NTP) particles with a pore size of about 10 nm were synthesized and blended with polyetheretherketone (PEEK) to fabricate a PEEK/NTP composite (PN). Subsequently, PN was treated by concentrated sulfuric acid to create a microporous surface (pore size of around 2 μm) on sulfonated PN (SPN), which formed a hierarchical micro & nanoporous surface. Compared with PN, the porous surface of SPN exhibited higher roughness, hydrophilicity, and surface energy. In addition, genistein (GT) was loaded into the porous surface of SPN (SPNG), which showed high GT loading capacity and sustained release of GT into phosphate buffered saline (PBS). Moreover, SPNG revealed excellent antibacterial activity, which inhibited bacterial (E. coli and S. aureus) growth in vitro due to the synergistic effects of both sulfonic acid (SO3H) groups and the sustained release of GT. Compared with PN, SPN significantly improved the adhesion, proliferation, and osteogenic differentiation of bone mesenchymal stem cells in vitro. Moreover, compared with SPN, SPNG further enhances the cell responses. Compared with PN, SPN remarkably improved bone formation and osteointegration in vivo. Furthermore, compared with SPN, SPNG further enhanced the osteointegration. In short, SPNG with a micro & nanoporous surface, SO3H groups, and the sustained release of GT exhibited antibacterial activity and accelerated osteointegration, which would have tremendous potential as drug-loaded implants for bone substitute.
Collapse
Affiliation(s)
- Shiqi Mei
- Key Laboratory for Ultrafine Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237, China.
| | | | | | | | | | | | | | | |
Collapse
|
6
|
Senevirathne SWMAI, Hasan J, Mathew A, Woodruff M, Yarlagadda PKDV. Bactericidal efficiency of micro- and nanostructured surfaces: a critical perspective. RSC Adv 2021; 11:1883-1900. [PMID: 35424086 PMCID: PMC8693530 DOI: 10.1039/d0ra08878a] [Citation(s) in RCA: 14] [Impact Index Per Article: 4.7] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/19/2020] [Accepted: 12/12/2020] [Indexed: 12/21/2022] Open
Abstract
Micro/nanostructured surfaces (MNSS) have shown the ability to inactivate bacterial cells by physical means. An enormous amount of research has been conducted in this area over the past decade. Here, we review the various surface factors that affect the bactericidal efficiency. For example, surface hydrophobicity of the substrate has been accepted to be influential on the bactericidal effect of the surface, but a review of the literature suggests that the influence of hydrophobicity differs with the bacterial species. Also, various bacterial viability quantification methods on MNSS are critically reviewed for their suitability for the purpose, and limitations of currently used protocols are discussed. Presently used static bacterial viability assays do not represent the conditions of which those surfaces could be applied. Such application conditions do have overlaying fluid flow, and bacterial behaviours are drastically different under flow conditions compared to under static conditions. Hence, it is proposed that the bactericidal effect should be assessed under relevant fluid flow conditions with factors such as shear stress and flowrate given due significance. This review will provide a range of opportunities for future research in design and engineering of micro/nanostructured surfaces with varying experimental conditions.
Collapse
Affiliation(s)
- S W M A I Senevirathne
- Science and Engineering Faculty, Queensland University of Technology (QUT) Brisbane Qld 4000 Australia
- Institute of Health and Biomedical Innovations 60 Musk Ave. Kelvin Grove Qld 4059 Australia
| | - J Hasan
- Science and Engineering Faculty, Queensland University of Technology (QUT) Brisbane Qld 4000 Australia
- Institute of Health and Biomedical Innovations 60 Musk Ave. Kelvin Grove Qld 4059 Australia
| | - A Mathew
- Science and Engineering Faculty, Queensland University of Technology (QUT) Brisbane Qld 4000 Australia
- Institute of Health and Biomedical Innovations 60 Musk Ave. Kelvin Grove Qld 4059 Australia
| | - M Woodruff
- Science and Engineering Faculty, Queensland University of Technology (QUT) Brisbane Qld 4000 Australia
- Institute of Health and Biomedical Innovations 60 Musk Ave. Kelvin Grove Qld 4059 Australia
| | - P K D V Yarlagadda
- Science and Engineering Faculty, Queensland University of Technology (QUT) Brisbane Qld 4000 Australia
- Institute of Health and Biomedical Innovations 60 Musk Ave. Kelvin Grove Qld 4059 Australia
| |
Collapse
|
7
|
Yang DL, Cui YN, Sun Q, Liu M, Niu H, Wang JX. Antibacterial activity and reinforcing effect of SiO2–ZnO complex cluster fillers for dental resin composites. Biomater Sci 2021; 9:1795-1804. [DOI: 10.1039/d0bm01834a] [Citation(s) in RCA: 14] [Impact Index Per Article: 4.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/25/2022]
Abstract
The regular-shaped SiO2-ZnO complex clusters constructed by spray-draying technology can enhance antibacterial activity while maintaining the mechanical and aesthetic properties of dental resin composites.
Collapse
Affiliation(s)
- Dan-Lei Yang
- State Key Laboratory of Organic-Inorganic Composites
- Beijing University of Chemical Technology
- Beijing
- PR China
- Research Center of the Ministry of Education for High Gravity Engineering and Technology
| | - Ya-Nan Cui
- Department of Prosthodontics
- Affiliated Stomatological Hospital of Anhui Medical University
- Anhui
- PR China
| | - Qian Sun
- State Key Laboratory of Organic-Inorganic Composites
- Beijing University of Chemical Technology
- Beijing
- PR China
- Research Center of the Ministry of Education for High Gravity Engineering and Technology
| | - Mei Liu
- Jiangsu Key laboratory of Oral Disease
- Department of Prosthodontics
- Affiliated Hospital of Stomatology
- Nanjing Medical University
- Nanjing
| | - Hao Niu
- State Key Laboratory of Organic-Inorganic Composites
- Beijing University of Chemical Technology
- Beijing
- PR China
- Research Center of the Ministry of Education for High Gravity Engineering and Technology
| | - Jie-Xin Wang
- State Key Laboratory of Organic-Inorganic Composites
- Beijing University of Chemical Technology
- Beijing
- PR China
- Research Center of the Ministry of Education for High Gravity Engineering and Technology
| |
Collapse
|
8
|
Sterzenbach T, Helbig R, Hannig C, Hannig M. Bioadhesion in the oral cavity and approaches for biofilm management by surface modifications. Clin Oral Investig 2020; 24:4237-4260. [PMID: 33111157 PMCID: PMC7666681 DOI: 10.1007/s00784-020-03646-1] [Citation(s) in RCA: 69] [Impact Index Per Article: 17.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/11/2020] [Accepted: 10/15/2020] [Indexed: 12/19/2022]
Abstract
BACKGROUND All soft and solid surface structures in the oral cavity are covered by the acquired pellicle followed by bacterial colonization. This applies for natural structures as well as for restorative or prosthetic materials; the adherent bacterial biofilm is associated among others with the development of caries, periodontal diseases, peri-implantitis, or denture-associated stomatitis. Accordingly, there is a considerable demand for novel materials and coatings that limit and modulate bacterial attachment and/or propagation of microorganisms. OBJECTIVES AND FINDINGS The present paper depicts the current knowledge on the impact of different physicochemical surface characteristics on bioadsorption in the oral cavity. Furthermore, it was carved out which strategies were developed in dental research and general surface science to inhibit bacterial colonization and to delay biofilm formation by low-fouling or "easy-to-clean" surfaces. These include the modulation of physicochemical properties such as periodic topographies, roughness, surface free energy, or hardness. In recent years, a large emphasis was laid on micro- and nanostructured surfaces and on liquid repellent superhydrophic as well as superhydrophilic interfaces. Materials incorporating mobile or bound nanoparticles promoting bacteriostatic or bacteriotoxic properties were also used. Recently, chemically textured interfaces gained increasing interest and could represent promising solutions for innovative antibioadhesion interfaces. Due to the unique conditions in the oral cavity, mainly in vivo or in situ studies were considered in the review. CONCLUSION Despite many promising approaches for modulation of biofilm formation in the oral cavity, the ubiquitous phenomenon of bioadsorption and adhesion pellicle formation in the challenging oral milieu masks surface properties and therewith hampers low-fouling strategies. CLINICAL RELEVANCE Improved dental materials and surface coatings with easy-to-clean properties have the potential to improve oral health, but extensive and systematic research is required in this field to develop biocompatible and effective substances.
Collapse
Affiliation(s)
- Torsten Sterzenbach
- Clinic of Operative and Pediatric Dentistry, Medical Faculty Carl Gustav Carus, Technische Universität Dresden, Fetscherstraße 74, 01307, Dresden, Germany.
| | - Ralf Helbig
- Max Bergmann Center of Biomaterials, Leibniz-Institut für Polymerforschung Dresden e.V., Hohe Straße 6, 01069, Dresden, Germany
| | - Christian Hannig
- Clinic of Operative and Pediatric Dentistry, Medical Faculty Carl Gustav Carus, Technische Universität Dresden, Fetscherstraße 74, 01307, Dresden, Germany
| | - Matthias Hannig
- Clinic of Operative Dentistry, Periodontology and Preventive Dentistry, University Hospital, Saarland University, Building 73, 66421, Homburg/Saar, Germany
| |
Collapse
|
9
|
Abstract
Antibiotic resistance is a global human health threat, causing routine treatments of bacterial infections to become increasingly difficult. The problem is exacerbated by biofilm formation by bacterial pathogens on the surfaces of indwelling medical and dental devices that facilitate high levels of tolerance to antibiotics. The development of new antibacterial nanostructured surfaces shows excellent prospects for application in medicine as next-generation biomaterials. The physico-mechanical interactions between these nanostructured surfaces and bacteria lead to bacterial killing or prevention of bacterial attachment and subsequent biofilm formation, and thus are promising in circumventing bacterial infections. This Review explores the impact of surface roughness on the nanoscale in preventing bacterial colonization of synthetic materials and categorizes the different mechanisms by which various surface nanopatterns exert the necessary physico-mechanical forces on the bacterial cell membrane that will ultimately result in cell death.
Collapse
|
10
|
Zhang K, Zhang B, Huang C, Gao S, Li B, Cao R, Cheng J, Li R, Yu Z, Xie X. Biocompatibility and antibacterial properties of pure titanium surfaces coated with yttrium-doped hydroxyapatite. J Mech Behav Biomed Mater 2019; 100:103363. [DOI: 10.1016/j.jmbbm.2019.07.021] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/09/2019] [Revised: 07/15/2019] [Accepted: 07/20/2019] [Indexed: 02/06/2023]
|
11
|
Asensio G, Vázquez-Lasa B, Rojo L. Achievements in the Topographic Design of Commercial Titanium Dental Implants: Towards Anti-Peri-Implantitis Surfaces. J Clin Med 2019; 8:E1982. [PMID: 31739615 PMCID: PMC6912779 DOI: 10.3390/jcm8111982] [Citation(s) in RCA: 29] [Impact Index Per Article: 5.8] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/17/2019] [Revised: 11/04/2019] [Accepted: 11/11/2019] [Indexed: 12/12/2022] Open
Abstract
Titanium and its alloys constitute the gold standard materials for oral implantology in which their performance is mainly conditioned by their osseointegration capacity in the host's bone. We aim to provide an overview of the advances in surface modification of commercial dental implants analyzing and comparing the osseointegration capacity and the clinical outcome exhibited by different surfaces. Besides, the development of peri-implantitis constitutes one of the most common causes of implant loss due to bacteria colonization. Thus, a synergic response from industry and materials scientists is needed to provide reliable technical and commercial solutions to this issue. The second part of the review focuses on an update of the recent findings toward the development of new materials with osteogenic and antibacterial capacity that are most likely to be marketed, and their correlation with implant geometry, biomechanical behavior, biomaterials features, and clinical outcomes.
Collapse
Affiliation(s)
- Gerardo Asensio
- Instituto de Ciencia y Tecnología de Polímeros, Consejo Superior de Investigaciones Científicas, CSIC, 28006 Madrid, Spain; (G.A.); (B.V.-L.)
| | - Blanca Vázquez-Lasa
- Instituto de Ciencia y Tecnología de Polímeros, Consejo Superior de Investigaciones Científicas, CSIC, 28006 Madrid, Spain; (G.A.); (B.V.-L.)
- Consorcio Centro de Investigación Biomédica en Red de Bioingeniería, Biomateriales y Nanomedicina, CIBER-BBN, 28029 Madrid, Spain
| | - Luis Rojo
- Instituto de Ciencia y Tecnología de Polímeros, Consejo Superior de Investigaciones Científicas, CSIC, 28006 Madrid, Spain; (G.A.); (B.V.-L.)
- Consorcio Centro de Investigación Biomédica en Red de Bioingeniería, Biomateriales y Nanomedicina, CIBER-BBN, 28029 Madrid, Spain
| |
Collapse
|
12
|
Dhaliwal JS, Rahman NA, Knights J, Ghani H, de Albuquerque Junior RF. The effect of different surface topographies of titanium implants on bacterial biofilm: a systematic review. SN APPLIED SCIENCES 2019. [DOI: 10.1007/s42452-019-0638-6] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/15/2022] Open
|
13
|
Falcón García C, Stangl F, Götz A, Zhao W, Sieber SA, Opitz M, Lieleg O. Topographical alterations render bacterial biofilms susceptible to chemical and mechanical stress. Biomater Sci 2019; 7:220-232. [DOI: 10.1039/c8bm00987b] [Citation(s) in RCA: 22] [Impact Index Per Article: 4.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/16/2022]
Abstract
Treatment with concentrated ethanol, saline or glucose solutions smoothens biofilm surface topography and initially superhydrophobic/omniphobic biofilms are rendered hydrophilic.
Collapse
Affiliation(s)
- Carolina Falcón García
- Department of Mechanical Engineering and Munich School of Bioengineering
- Technical University of Munich
- 85748 Garching
- Germany
| | - Felix Stangl
- Department of Mechanical Engineering and Munich School of Bioengineering
- Technical University of Munich
- 85748 Garching
- Germany
| | - Alexandra Götz
- Center for NanoScience
- Faculty of Physics
- Ludwig-Maximilians-Universität München
- Munich
- Germany
| | - Weining Zhao
- Department of Chemistry
- Chair for Organic Chemistry II
- Technical University of Munich
- 85748 Garching
- Germany
| | - Stephan A. Sieber
- Department of Chemistry
- Chair for Organic Chemistry II
- Technical University of Munich
- 85748 Garching
- Germany
| | - Madeleine Opitz
- Center for NanoScience
- Faculty of Physics
- Ludwig-Maximilians-Universität München
- Munich
- Germany
| | - Oliver Lieleg
- Department of Mechanical Engineering and Munich School of Bioengineering
- Technical University of Munich
- 85748 Garching
- Germany
| |
Collapse
|
14
|
Scharnweber D, Bierbaum S, Wolf-Brandstetter C. Utilizing DNA for functionalization of biomaterial surfaces. FEBS Lett 2018; 592:2181-2196. [PMID: 29683477 DOI: 10.1002/1873-3468.13065] [Citation(s) in RCA: 10] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Key Words] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/28/2018] [Revised: 03/27/2018] [Accepted: 04/16/2018] [Indexed: 02/06/2023]
Abstract
DNA sequences are widely used for gene transfer into cells including a number of substrate surface-based supporting systems, but due to its singular structure property profile, DNA also offers multiple options for noncanonical applications. The special case of using DNA and oligodeoxyribonucleotide (ODN) structures for surface functionalization of biomedical implants is summarized here with the major focus on (a) immobilization or anchoring of nucleic acid structures on substrate surfaces, (b) incorporation of biologically active molecules (BAM) into such systems, and (c) biological characteristics of the resulting surfaces in vitro and in vivo. Sterilizations issues, important for potential clinical applications, are also considered.
Collapse
Affiliation(s)
- Dieter Scharnweber
- Max Bergmann Center of Biomaterials, Technische Universität Dresden, Germany
| | - Susanne Bierbaum
- Max Bergmann Center of Biomaterials, Technische Universität Dresden, Germany.,International Medical College, Münster, Germany
| | | |
Collapse
|