Photonic crystal-assisted sub-bandgap photocatalysis via triplet-triplet annihilation upconversion for the degradation of environmental organic pollutants

This study explores novel approaches to enhance photocatalysis efficiency by introducing a photonic crystal (PC)-enhanced, multi-layered sub-bandgap photocatalytic reactor. The design aims to effectively utilize sub-bandgap photons that might otherwise go unused. The device consists of three types of layers: (1) two polymeric triplet-triplet annihilation upconversion (TTA-UC) layers converting low-energy green photons (λEx = 532 nm, 2.33 eV) to high-energy blue photons (λEm = 425 nm, 2.92 eV), (2) a platinum-decorated WO3 layer (Eg = 2.8 eV) serving as a visible-light photocatalyst, and (3) a PC layer optimizing both TTA-UC and photocatalysis. The integration of the PC layer resulted in a 1.9-fold increase in UC emission and a 7.9-fold enhancement in hydroxyl radical (•OH) generation, achieved under low-intensity sub-bandgap irradiation (17.6 mW cm-2). Consequently, the combined layered structure of TTA/Pt-WO3/TTA/PC achieved a remarkable 38.8-fold improvement in •OH production, leading to outstanding degradation capability for various organic pollutants (e.g., 4-chlorophenol, bisphenol A, and methylene blue). This multi-layered sub-bandgap photocatalytic structure, which uniquely combines TTA-UC and PC layers, offers valuable insights into designing efficient photocatalytic systems for future solar-driven environmental remediation.

Converting Glycerol into Valuable Trioses by Cuδ+ -Single-Atom-Decorated WO3 under Visible Light

Photocatalytic selective oxidation under visible light presents a promising approach for the sustainable transformation of biomass-derived wastes. However, achieving both high conversion and excellent selectivity poses a significant challenge. In this study, two valuable trioses, glyceraldehyde and dihydroxyacetone, are produced from glycerol over Cuδ+ -decorated WO3 photocatalyst in the presence of H2 O2 . The photocatalyst exhibits a remarkable five-fold increase in the conversion rate (3.81 mmol ⋅ g-1  ⋅ h-1 ) while maintaining a high selectivity towards two trioses (46.4 % to glyceraldehyde and 32.9 % to dihydroxyacetone). Through a comprehensive analysis involving X-ray photoelectron spectroscopy measurements with and without light irradiation, electron spin resonance spectroscopy, and isotopic analysis, the critical role of Cu+ species has been explored as efficient hole acceptors. These species facilitate charge transfer, promoting glycerol oxidation by photoholes, followed by coupling with OH- , which are subsequently dehydrated to yield the desired glyceraldehyde and dihydroxyacetone.

Advances and perspectives of nanomaterials for photocatalytic degradation of biological ethylene toward the postharvest improvement of agricultural products

To date, intensive emphasis is required to develop advanced postharvest technologies to ensure food security, increase nutrition, and improve farmers toward cleaner production. How to effectively degrade the harmful gaseous ethylene (C2H4) biosynthesis, which distributes heavy losses of fresh-cut fruits and vegetables, has received considerable attention. Among various advanced techniques, photocatalytic degradation of biological C2H4 is proposed as the most promising method to solve this issue. In this context, the recent studies on the photodegradation of C2H4 have been critically summarized and highlighted. Many photocatalysts, including TiO2-based and non-TiO2-based (metal oxides (ZnO, WO3, Ga2O3), molybdates (β-Ag2MoO4), phosphides (Ag3PO4), perovskite oxides (Bi2WO6)) nanomaterials, have been revealed with credible performance results. Also, varying reaction parameters to optimize the photocatalytic degradation efficacy in the literature are summarized. We also discussed the current status, challenges, and prospects for enhanced photodegradation of C2H4 in this study. The efficacy and economics of photodegradation have played an essential role in selecting a particular type of photocatalyst. Although many efforts have been made, significant improvements are still required for photocatalysis. In this work, we have also successfully suggested some strategies to further promote this concept for controlling and degrading plant-generated C2H4 in fruit and vegetable postharvest in a sustainable and economically feasible manner.

Photoelectrochemical Methods for the Determination of the Flat-Band Potential in Semiconducting Photocatalysts: A Comparison Study

In addition to the band gap of a semiconducting photocatalyst, its band edges are important because they play a crucial role in the analysis of charge transfer and possible pathways of the photocatalytic reaction. The Mott-Schottky method using electrochemical impedance spectroscopy is the most common experimental technique for the determination of the electron potential in photocatalysts. This method is well suited for large crystals, but in the case of nanocatalysts, when the thickness of the charged layer is comparable with the size of the nanocrystals, the capacitance of the Helmholtz layer can substantially affect the measured potential. A contact between the electrolyte and the substrate, used for deposition of the photocatalyst, also affects the impedance. Application of other photoelectrochemical methods may help to avoid concerns in the interpretation of impedance data and improve the reliability of measurements. In this study, we have successfully prepared five visible-light active photocatalysts (i.e., N-doped TiO2, WO3, Bi2WO6, CoO, and g-C3N4) and measured their flat-band potentials using four (photo)electrochemical methods. The potentials are compared for all methods and discussed regarding the type of semiconducting material and its properties. The effect of methanol as a sacrificial agent for the enhanced transfer of charge carriers is studied and discussed for each method.

Photocatalytic degradation of organic pollutants and inactivation of pathogens under visible light via SnO2/rGO composites

The domains of environmental cleanup and pathogen inactivation are particularly interesting in nanocomposites (NCs) due to their exceptional physicochemical properties. Tin oxide/reduced graphene oxide nanocomposites (SnO₂/rGO NCs) have potential uses in the biological and environmental fields, but little is known about them. This study aimed to investigate the photocatalytic activity and antibacterial efficiency of the nanocomposites. The co-precipitation technique was used to prepare all the samples. XRD, SEM, EDS, TEM, and XPS analyses were employed to characterize the physicochemical properties of SnO₂/rGO NCs for structural analysis. The rGO loading sample resulted in a decrease in the crystallite size of SnO₂ nanoparticles. TEM and SEM images demonstrate the firm adherence of SnO₂ nanoparticles to the rGO sheets. The chemical state and elemental composition of the nanocomposites were validated by the XPS and EDS data. Additionally, the visible-light active photocatalytic and antibacterial capabilities of the synthesized nanocomposites were assessed for the degradation of Orange II and methylene blue, as well as the suppression of the growth of S. aureus and E. coli. As a result, the synthesized SnO₂/rGO NCs are improved photocatalysts and antibacterial agents, expanding their potential in the fields of environmental remediation and water disinfection.

Polymeric graphitic carbon nitride layers decorated with erbium oxide and enhanced photocatalytic performance under visible light irradiation

Developing and implementing visible light active organic-inorganic hybrid semiconductor nanomaterials with enhanced photocatalytic properties find newer environmental and energy treatment capabilities. Here, we are reporting polymeric g-C₃N₄ layers coated with different propositions of erbium oxide nanoparticles, characterized using XPS, UV-Vis-DRS, FT-IR, HR-TEM, FE-SEM, elemental mapping, XRD and surface area techniques and its photocatalytic activities were evaluated under visible light irradiations. The hybrid nanocomposite materials possess better crystalline nature and erbium oxide particles were on the surface of polymeric g-C₃N₄. The surface area and bandgap energy of the polymeric g-C₃N₄-erbium oxide (5 wt%) nanohybrid composite were 99.9 m²/g and 2.52 eV. The photocatalytic activities as prepared nanohybrid composites were assessed for the oxidation of orange G dye molecules in the presence of visible light and were highly active in a broader range of pH with the presence of various inorganic anions. The rate of photocatalytic oxidation of dye molecules varied from 4.79 × 10^-4 to 1.77 × 10^-4 min^-1 for the initial concentration of 5 to 20 ppm and retained its activities above 95% up to three cycles of reusability. Hence, the organic-inorganic novel catalytic nanohybrid composite may find more comprehensive applications in the area of environmental and energy applications.

Self-assembly of CdSe 3D urchins and their photocatalytic response

Photocatalysis is found to be one of the best suited processes that respond to the purification of water systems and the semiconductor nanomaterials are learned to be incredible materials which carry out the photocatalytic process as they readily decompose the pollutants effectively. In this present work, CdSe nanoparticles belonging to II-VI group semiconductor compounds were synthesized using a facile hydrothermal process with different precursor concentrations and were analysed for various characterization studies such as X-ray diffraction (XRD), Transmission electron microscopy (TEM), UV-vis absorption spectroscopy, Fourier transform infrared spectroscopy (FTIR) and Photoluminescence (PL) studies. The XRD study of the synthesized CdSe nanostructures revealed that the average crystallite size was ranging from 18.5 nm to 24 nm pointing out the increase in size with increase in molar concentrations. The morphological structure of synthesized CdSe samples exhibited urchin-like structure for a lower concentration with several rod-like projections appearing in diverse directions. These CdSe nano-urchins synthesized with lower concentrations are found suitable to carry out the process of photocatalytic activity. The process was carried out under visible light radiation for 180 min with aqueous solution of methylene blue (MB) as the ideal toxin to be degraded. The attained degradation efficiency was nearly 80% clearly displaying that the synthesized samples are good photocatalysts. By tuning the bandgap, through the optimization of the precursor concentrations, greater efficiency can be achieved in future.

Solution combustion synthesis: the relevant metrics for producing advanced and nanostructured photocatalysts

The current developments and progress in energy and environment-related areas pay special attention to the fabrication of advanced nanomaterials via green and sustainable paths to accomplish chemical circularity. The design and preparation methods of photocatalysts play a prime role in determining the structural, surface characteristics and optoelectronic properties of the final products. The solution combustion synthesis (SCS) technique is a relatively novel, cost-effective, and efficient method for the bulk production of nanostructured materials. SCS-fabricated metal oxides are of great technological importance in photocatalytic, environmental and energy applications. To date, the SCS route has been employed to produce a large variety of solid materials such as metals, sulfides, carbides, nitrides and single or complex metal oxides. This review intends to provide a holistic perspective of the different steps involved in the chemistry of SCS of advanced photocatalysts, and pursues several SCS metrics that influence their photocatalytic performances to establish a feasible approach to design advanced photocatalysts. The study highlights the fundamentals of SCS and the importance of various combustion parameters in the characteristics of the fabricated photocatalysts. Consequently, this work deals with the design of a concise framework to link the fine adjustment of SCS parameters for the development of efficient metal oxide photocatalysts for energy and environmental applications.

Hydrothermal Synthesis of Co-Exposed-Faceted WO3 Nanocrystals with Enhanced Photocatalytic Performance

In this paper, rod-shaped, cuboid-shaped, and irregular WO₃ nanocrystals with different co-exposed crystal facets were prepared for the first time by a simple hydrothermal treatment of tungstic acid colloidal suspension with desired pH values. The crystal structure, morphology, specific surface area, pore size distribution, chemical composition, electronic states of the elements, optical properties, and charge migration behavior of as-obtained WO₃ products were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), fully automatic specific surface area and porosity analyzer, UV-vis absorption spectra, photoluminescence (PL) spectra, and electrochemical impedance spectroscopy (EIS). The photocatalytic performances of the synthesized pHx-WO₃ nanocrystals (x = 0.0, 1.5, 3.0, 5.0, and 7.0) were evaluated and compared with the commercial WO₃ (CM-WO₃) nanocrystals. The pH7.0-WO₃ nanocrystals with co-exposed {202} and {020} facets exhibited highest photocatalytic activity for the degradation of methylene blue solution, which can be attributed to the synergistic effects of the largest specific surface area, the weakest luminescence peak intensity and the smallest arc radius diameter.

Catalytic activity imperative for nanoparticle dose enhancement in photon and proton therapy

Nanoparticle-based radioenhancement is a promising strategy for extending the therapeutic ratio of radiotherapy. While (pre)clinical results are encouraging, sound mechanistic understanding of nanoparticle radioenhancement, especially the effects of nanomaterial selection and irradiation conditions, has yet to be achieved. Here, we investigate the radioenhancement mechanisms of selected metal oxide nanomaterials (including SiO₂, TiO₂, WO₃ and HfO₂), TiN and Au nanoparticles for radiotherapy utilizing photons (150 kVp and 6 MV) and 100 MeV protons. While Au nanoparticles show outstanding radioenhancement properties in kV irradiation settings, where the photoelectric effect is dominant, these properties are attenuated to baseline levels for clinically more relevant irradiation with MV photons and protons. In contrast, HfO₂ nanoparticles retain some of their radioenhancement properties in MV photon and proton therapies. Interestingly, TiO₂ nanoparticles, which have a comparatively low effective atomic number, show significant radioenhancement efficacies in all three irradiation settings, which can be attributed to the strong radiocatalytic activity of TiO₂, leading to the formation of hydroxyl radicals, and nuclear interactions with protons. Taken together, our data enable the extraction of general design criteria for nanoparticle radioenhancers for different treatment modalities, paving the way to performance-optimized nanotherapeutics for precision radiotherapy.

Nanoparticles have recently received attention in radiation therapy since they can act as radioenhancers. In this article, the authors report on the dose enhancement capabilities of a series of nanoparticles based on their metal core composition and beam characteristics, obtaining designing criteria for their optimal performance in specific radiotreatments.

One-Pot Synthesis of SnO2-rGO Nanocomposite for Enhanced Photocatalytic and Anticancer Activity

Metal oxide and graphene derivative-based nanocomposites (NCs) are attractive to the fields of environmental remediation, optics, and cancer therapy owing to their remarkable physicochemical characteristics. There is limited information on the environmental and biomedical applications of tin oxide-reduced graphene oxide nanocomposites (SnO₂-rGO NCs). The goal of this work was to explore the photocatalytic activity and anticancer efficacy of SnO₂-rGO NCs. Pure SnO₂ NPs and SnO₂-rGO NCs were prepared using the one-pot hydrothermal method. X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR), UV–Vis spectrometry, photoluminescence (PL), and Raman scattering microscopy were applied to characterize the synthesized samples. The crystallite size of the SnO₂ NPs slightly increased after rGO doping. TEM and SEM images show that the SnO₂ NPs were tightly anchored onto the rGO sheets. The XPS and EDX data confirmed the chemical state and elemental composition of the SnO₂-rGO NCs. Optical data suggest that the bandgap energy of the SnO₂-rGO NCs was slightly lower than for the pure SnO₂ NPs. In comparison to pure SnO₂ NPs, the intensity of the PL spectra of the SnO₂-rGO NCs was lower, indicating the decrement of the recombination rate of the surfaces charges (e⁻/h⁺) after rGO doping. Hence, the degradation efficiency of methylene blue (MB) dye by SnO₂-rGO NCs (93%) was almost 2-fold higher than for pure SnO₂ NPs (54%). The anticancer efficacy of SnO₂-rGO NCs was also almost 1.5-fold higher against human liver cancer (HepG2) and human lung cancer (A549) cells compared to the SnO₂ NPs. This study suggests a unique method to improve the photocatalytic activity and anticancer efficacy of SnO₂ NPs by fusion with graphene derivatives.

Enhanced sun light driven photocatalytic activity of Co doped SnO2 loaded corn cob activated carbon for methylene blue dye degradation

SnO₂ with different Co²⁺ doping concentrations and Co (0.075 M): SnO₂ loaded corn cob activated carbon (Co: SnO₂/CCAC) were prepared, and are labelled as CS1, CS2, CS3 and CS2/CCAC, respectively. The CS2/CCAC showed that the particle size (18.76 nm) and band gap (3.50 eV) are reduced with Co²⁺ doping and CCAC loading. Moreover, CS2/CCAC indicate that the decreased PL intensity and its lower value (2.156 kΩ) of impedance from EIS results which indicates the increased separation of the photogenerated e^-/h⁺ pairs. Thus, the result showed that CS2/CCAC maximum degradation efficiency of MB (95.38%) and the photocatalytic mechanism is also discussed.

Titanium dioxide based nanocomposites - Current trends and emerging strategies for the photocatalytic degradation of ruinous environmental pollutants

Many ruinous pollutants are omnipresent in the environment and among them; pesticides are xenobiotic and pose to be a bio-recalcitrance. Their detrimental ecological and environmental impacts attract attention of environmental excerpts and the surge of stringent regulations have endows the need of a technically feasible treatment. This critical review emphasizes about the occurrence, abundance and fate of structurally distinct pesticides in different environment. The practiced remedial strategies and in particular, the advanced oxidation processes (AOPs) those utilize the photo-catalytic properties of nano-composites for the degradation of pollutants are critically discussed. Photo-catalytic degradation utilizes many composite materials at nano-scale level, wherein synthesis of nano-composites with appropriate precursors and other adjoining functional moieties are of prime importance. Therefore, suitable starter materials along with the reaction conditions are prerequisite for effectively tailoring the nano-composites. The aforementioned aspects and their customized applications are critically discussed. The associated challenges, opportunities and process economics of degradation using photo-catalytic AOP techniques are highlighted and in addition, the review tries to explain how best the photo-degradation can be a stand-alone tool with a societal importance. Conclusively, the future prospects for undertaking new researches in photo-catalytic breakdown of pollutants that can be judiciously sustainable.

A Novel N-Doped Nanoporous Bio-Graphene Synthesized from Pistacia lentiscus Gum and Its Nanocomposite with WO3 Nanoparticles: Visible-Light-Driven Photocatalytic Activity

This paper reports the synthesis of a new nitrogen-doped porous bio-graphene (NPBG) with a specific biomorphic structure, using Pistacia lentiscus as a natural carbon source containing nitrogen that also acts as a bio-template. The obtained NPBG demonstrated the unique feature of doped nitrogen with a 3D nanoporous structure. Next, a WO₃/N-doped porous bio-graphene nanocomposite (WO₃/NPBG-NC) was synthesized, and the products were characterized using XPS, SEM, TEM, FT-IR, EDX, XRD, and Raman analyses. The presence of nitrogen doped in the structure of the bio-graphene (BG) was confirmed to be pyridinic-N and pyrrolic-N with N1 peaks at 398.3 eV and 400.5 eV, respectively. The photocatalytic degradation of the anionic azo dyes and drugs was investigated, and the results indicated that the obtained NPBG with a high surface area (151.98 m²/g), unique electronic properties, and modified surface improved the adsorption and photocatalytic properties in combination with WO₃ nanoparticles (WO₃-NPs) as an effective visible-light-driven photocatalyst. The synthesized WO₃/NPBG-NC with a surface area of 226.92 m²/g displayed lower bandgap and higher electron transfer compared with blank WO₃-NPs, leading to an increase in the photocatalytic performance through the enhancement of the separation of charge and a reduction in the recombination rate. At the optimum conditions of 0.015 g of the nanocomposite, a contact time of 15 min, and 100 mg/L of dyes, the removal percentages were 100%, 99.8%, and 98% for methyl red (MR), Congo red (CR), and methyl orange (MO), respectively. In the case of the drugs, 99% and 87% of tetracycline and acetaminophen, respectively, at a concentration of 10 mg/L, were removed after 20 min.

Elimination or Removal of Ethylene for Fruit and Vegetable Storage via Low-Temperature Catalytic Oxidation

Ethylene acts as an important hormone to trigger the ripening and senescence of fruits and vegetables (F&V). Thus, it is essential to eliminate trace ethylene and prevent F&V losses effectively. There are several technologies currently applying to control the ethylene concentration in the storage and transportation environment, including adsorption, gene modification, oxidation, etc. These protocols will be compared, and special attention will be paid to the low-temperature catalytic oxidation that has already been applied to practical production in this review. The active sites, supports, and reaction and deactivation mechanism of the catalysts for the low-temperature ethylene oxidation will be discussed and evaluated systematically to provide new insights for the development of effective catalysts, along with the suggestion of some perspectives for future research on this important catalytic system for F&V preservation.

Bifunctional Nitrogen-Doped Carbon Dots in g-C3N4/WOx Heterojunction for Enhanced Photocatalytic Water-Splitting Performance

A novel metal-free all-solid-state z-scheme g-C₃N₄/NCDs/WO_x photocatalyst was fabricated using nitrogen-doped carbon dots (NCDs) as the electron mediator. As-prepared sandwich-structured composites displayed enhanced visible and NIR light photocatalytic activity. Under visible light irradiation, the hydrogen evolution rate reached 3.27 mmol g^-1 h^-1, which increased to roughly seven times higher than that of pure g-C₃N₄ and roughly twice that of g-C₃N₄/NCDs or g-C₃N₄/WO_x binary heterojunctions. The apparent quantum efficiency is 7.58% at 420 nm. The localized surface plasmon resonance effect of WO_x and the up-converted photoluminescence property of NCDs enhanced the utilization efficiency of NIR light together. In addition, the matched energy band structures of WO_x and g-C₃N₄ as well as the effective electron conductor (NCDs) between them accelerate electron transfer at the interface. The all-solid-state z-scheme g-C₃N₄/NCDs/WO_x photocatlyst was confirmed by a series of characterizations and experiment results. This report offered new insights into constructing an efficient all-solid-state z-scheme photocatalyst to be applied during the photocatalytic water-splitting reaction in the visible and NIR light regions.

TiO2 Photocatalysis for the Transformation of Aromatic Water Pollutants into Fuels

The growing world energy consumption, with reliance on conventional energy sources and the associated environmental pollution, are considered the most serious threats faced by mankind. Heterogeneous photocatalysis has become one of the most frequently investigated technologies, due to its dual functionality, i.e., environmental remediation and converting solar energy into chemical energy, especially molecular hydrogen. H2 burns cleanly and has the highest gravimetric gross calorific value among all fuels. However, the use of a suitable electron donor, in what so-called “photocatalytic reforming”, is required to achieve acceptable efficiency. This oxidation half-reaction can be exploited to oxidize the dissolved organic pollutants, thus, simultaneously improving the water quality. Such pollutants would replace other potentially costly electron donors, achieving the dual-functionality purpose. Since the aromatic compounds are widely spread in the environment, they are considered attractive targets to apply this technology. In this review, different aspects are highlighted, including the employing of different polymorphs of pristine titanium dioxide as photocatalysts in the photocatalytic processes, also improving the photocatalytic activity of TiO2 by loading different types of metal co-catalysts, especially platinum nanoparticles, and comparing the effect of various loading methods of such metal co-catalysts. Finally, the photocatalytic reforming of aromatic compounds employing TiO2-based semiconductors is presented.

Two-Dimensional Tungsten Oxide/Selenium Nanocomposite Fabricated for Flexible Supercapacitors with Higher Operational Voltage and Their Charge Storage Mechanism

The present work elaborates the high-energy-density, stable, and flexible supercapacitor devices (full-cell configuration with asymmetric setup) based on a two-dimensional tungsten oxide/selenium (2D WO₃/Se) nanocomposite. For this, the 2D WO₃/Se nanocomposite synthesized by a hydrothermal method followed by air annealing was coated on a flexible carbon cloth current collector and combined separately with both 0.1 M H₂SO₄ and 1-butyl-3-methyl imidazolium tetrafluoroborate room temperature ionic liquid (BmimBF₄ RTIL) as electrolyte. Different physicochemical characterization techniques, viz., transmission electron microscopy, scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy, are utilized for phase confirmation and morphology identification of the obtained samples. The electrochemical analysis was used to evaluate charge storage mechanism. The half-cell configuration (three electrode system) in 0.1 M H₂SO₄ shows a specific capacitance of 564 F g^-1 at 6 A g^-1 current density, whereas with ionic liquid as electrolyte, a higher specific capacitance of 1650 F g^-1 was obtained at a higher current of 40 mA and working potential of 4 V. Importantly, the asymmetric flexible supercapacitor device with PVA-H₂SO₄ electrolyte shows a working voltage of 1.7 V. A specific capacitance of 858 mF g^-1 is obtained for the asymmetric electrode system with an energy density of 47 mWh kg^-1 and a power density of 345 mW kg^-1 at a current density of 0.2 A g^-1.

Nickel and sulfur codoped TiO2 nanoparticles for efficient visible light photocatalytic activity

In this work, Nickel (Ni) and sulfur (S) codoped TiO2 nanoparticles were prepared by a sol-gel technique. The as-prepared catalyst was characterized using X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), FT-Raman spectroscopy, scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), transmission electron microscopy (TEM), UV-Vis diffuse reflectance spectra (DRS) for investigating crystal structure, crystal phase, particle size and bandgap energy of these samples. The photocatalytic performances of all the prepared catalysts have been investigated for the degradation of methylene blue (MB) under visible light irradiation. It was noticed that Ni-S codoped TiO2(Ni-S/TiO2) nanoparticles exhibited much higher photocatalytic activity compared with pure, Ni and S doped TiO2 due to higher visible light absorption and probable decrease in the recombination of photo-generated charges. It was decided that the great visible light absorption was created for codoped TiO2 by the formation of impurity energy states near both the edges of the collection, which works as trapping sites for both the photogenerated charges to decrease the recombination process.

Comparison of Enhanced Photocatalytic Degradation Efficiency and Toxicity Evaluations of CeO2 Nanoparticles Synthesized Through Double-Modulation

We demonstrated that Fe/Cr doped and pH-modified CeO₂ nanoparticles (NPs) exhibit enhanced photocatalytic performance as compared to bare CeO₂ NPs, using photocatalytic degradation. To assess the toxicity level of these double-modified CeO₂ NPs on the human skin, they were introduced into HaCaT cells. The results of our conventional cellular toxicity assays (neutral red uptake and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide for assays) indicated that Cr@CeO_x NPs prompt severe negative effects on the viability of human cells. Moreover, the results obtained by scanning transmission X-ray microscopy and bio-transmission electron microscope analysis showed that most of the NPs were localized outside the nucleus of the cells. Thus, serious genetic toxicity was unlikely. Overall, this study highlights the need to prevent the development of Cr@CeO_x NP toxicity. Moreover, further research should aim to improve the photocatalytic properties and activity of these NPs while accounting for their stability issues.

WO3-x horizontally-grown on TiO2(B) nanosheets for enhanced photo- and electro-chemical activity

WO3-x was deposited on TiO2(B) nanosheets prepared using TiCl4 to form layered heterostructures via a two-step solvothermal synthesis, in which the horizontal growth of WO3-x on TiO2(B) nanosheets was carried out using WCl6 and ascorbic acid as a reducer. Optimized preparation conditions allowed WO3-x/TiO2(B) layered heterostructures to be formed. The photo- and electro-chemical properties of layered heterostructures depended strongly on the amount of WO3-x. The WO3-x/TiO2(B) heterostructures demonstrated perfect catalytic performance in full solar-spectrum light and a fast degradation effect for dye and organic colorless pollutant. All target chemicals were degraded within 10 min using WO3-x/TiO2(B) samples as a photo-catalyst in the full solar-spectrum. The photo-assisted production kinetic of Cr(VI) ions were tested. The results indicate that the reproduction rate of Cr(VI) ions using WO3-x/TiO2(B) sample is three times higher than the initial TiO2 nanosheets. The result of the photo current and Mott-Shottky curve indicates that enhanced catalysis activity is ascribed to the surface of the metastable TiO2(B) with Ti3+ defects and oxygen vacancies as active sites for photocatalytic reaction. In addition, the loading of WO3-x greatly broadened the light absorption range of TiO2(B), meaning that the product responded in the full solar spectrum.

Fabrication of Ag2O/WO3 p-n heterojunction composite thin films by magnetron sputtering for visible light photocatalysis

Semiconductor-based nanostructures which are photo-catalytically active upon solar light irradiation were extensively used for environmental remediation due to the potential decomposition of various kinds of pollutants. In this work, we report the preparation of a sustainable thin film composite, i.e. Ag₂O/WO₃ p–n heterojunction, and investigation of its photocatalytic activity. To achieve the composite structure, WO₃/Ag–WO₃ layers were deposited over a quartz substrate by magnetron sputtering at room temperature and subsequently annealed at 823 to 923 K. The thin film structure, morphology, and chemical states were thoroughly characterized by X-ray diffraction, field-emission scanning electron microscopy, transmission electron spectroscopy, and X-ray photoelectron spectroscopy. The obtained results revealed that the amorphous Ag-doped WO₃ was crystallized into monoclinic WO₃ and Ag₂O, in which nanocrystalline Ag₂O was diffused towards the surface of WO₃. Optical transmittance spectra recorded by UV-vis-NIR spectroscopy revealed that the WO₃/Ag–WO₃ films became transparant in the visible region after annealing at high temperature (873 K and 923 K). The Ag₂O/WO₃ p–n heterojunction composite thin films showed high photocatalytic activity (0.915 × 10⁻³ min⁻¹) under visible light irradiation, which is attributed to the efficiency of effective photogenerated charge-carrier formation and the reduced recombination rate of photogenerated electron–hole pairs. Unlike the powder-based photocatalysts, the reported thin film-based heterojunction photocatalyst could be very sustainable, and cost-effective.

Semiconductor-based nanostructures which are photo-catalytically active upon solar light irradiation were extensively used for environmental remediation due to the potential decomposition of various kinds of pollutants.

The Multiple Promotion Effects of Ammonium Phosphate-Modified Ag3PO4 on Photocatalytic Performance

Phosphate ( PO 4 3 - ) modification of semiconductor photocatalysts such as TiO₂, C₃N₄, BiVO₄, and etc. has been shown positive effect on the enhancement of photocatalytic performance. In the present study, we demonstrate a novel one-pot surface modification route on Ag₃PO₄ photocatalyst by ammonium phosphate [(NH₄)₃PO₄], which combines PO 4 3 - modification with ammonium ( NH 4 + ) etching to show multiple effects on the structural variation of Ag₃PO₄ samples. The modified Ag₃PO₄ photocatalysts exhibit much higher photocatalytic performance than bare Ag₃PO₄ for the degradation of organic dye solutions under visible light irradiation. It is indicated that the NH 4 + etching favors the surface transition from Ag₃PO₄ to metallic Ag nanoparticles, resulting in the fast capture of photogenerated electrons and the followed generation of O 2 · - radicals. The strongly adsorbed PO 4 3 - on the Ag₃PO₄ surfaces can further provide more negative electrostatic field, which improves the separation of photogenerated electron-hole pairs by inducing the holes to directly flow to the surface and then enhances the formation of reactive ·OH radicals. Furthermore, the photocatalytic performance of the modified Ag₃PO₄ photocatalysts can be optimized by monitoring the concentration of (NH₄)₃PO₄ that is 1 mM.

Seaweed bio-inspired ZnO piezoelectric cilia array applied in microreactors for enhanced photocatalytic performance

A piezoelectric built-in electric field is believed to be an effective way to separate photoinduced carriers and enhance photocatalytic performance.

An advanced composite with ultrafast photocatalytic performance for the degradation of antibiotics by natural sunlight without oxidizing the source over TMU-5@Ni–Ti LDH: mechanistic insight and toxicity assessment

Pharmaceuticals are considered as emerging organic contaminants that have become a serious environmental problem, which endanger human health and environmental bio-diversity.

ZnO nanorods modified with noble metal-free Co3O4 nanoparticles as a photocatalyst for efficient ethylene degradation under light irradiation

ZnO modified with noble metal-free Co₃O₄ nanoparticles was prepared by a simple method and showed good stability and high efficiency for photo-oxidizing ethylene.