Construction of Synergistic Co/CoO Interface to Enhance Hydrogenation Activity of Ethyl Lactate to 1,2-Propanediol

The development of effective and stable non-precious catalysts for hydrogenation of ester to diols remains a challenge. Herein, the catalytic hydrogenation of ethyl lactate (EL) to 1,2-propanediol (1,2-PDO) with supported Co catalysts derived from layered double hydroxides (LDHs) is investigated. Catalytic tests reveal that LDH-derived Co catalysts exhibit the best catalytic performance with 98 % of EL conversion and >99 % of 1,2-PDO selectivity at mild conditions, compared with other Co catalysts (supported on Al2 O3 , and TiO2 ) and LDH-derived Cu catalysts. Due to the strong interaction among Co and Al matrix, the main composition is metallic Co0 and CoO after reduction at 600 °C. Besides, the catalyst shows good recyclability in the liquid phase hydrogenation. The superior catalytic performance can be attributed to the synergistic effect between Co0 and CoO, in which H2 molecule is activated on Co0 and EL is strongly adsorbed on CoO via hydroxyl groups.

Ni-Mg/Al Mixed Oxides Prepared from Double Layered Hydroxides as Catalysts for the Conversion of Furfural to Tetrahydrofurfuryl Alcohol

Ni-Mg/Al mixed oxide catalysts (Ni2Al, Ni2Mg1Al, and Ni1Mg1Al) obtained from layered double hydroxides (LDHs) were tested on the one-pot production of tetrahydrofurfuryl alcohol (TFA) from furfural (FF). Upon calcination at 400 °C and reduction at 500 °C, the LDHs gave catalysts containing small nickel crystallites (<4 nm) dispersed on mixtures of metal oxides and spinel structures. Complete conversion of FF (>99.5%) was achieved on all the catalysts after 4 h at 190 °C and 5.0 MPa of H2 using 5 wt.% FF in ethanol and a furfural-to-catalyst mass ratio of 7.44 g/g. TFA evolved from the sequential hydrogenation of FF to furfuryl alcohol (FA) to TFA. Competing reaction routes involved decarbonylation of FF to furan (FUR) followed by hydrogenation to tetrahydrofuran (THF) or hydrogenolysis to n-butane (BU) and the hydrogenation of the carbonyl group in FF to form 2-methyl furan (mFUR) and its hydrogenation to 2-methyltetrahydrofuran (mTHF). A third competing route consisted of the nucleophilic addition of FF with ethanol and with FA to form acetals (such as 2-(diethoxymethyl)furan, FDA), which were later converted to difurfuryl ether (DFE) and tetrahydrofurfuryl ethyl ether (TFEE) as final products. Hydrogen pressure favored the production of TFA and diminished the formation of acetals, while temperature reduced the capacity of the catalyst to hydrogenate the furan ring, thus reducing TFA and increasing FA and FUR. An 80% yield to TFA was achieved with the Ni2Mg1Al catalysts after 6 h at 190 °C and 50 bar H2, but a variety of coproducts were present at low concentration. Testing of the catalysts in gas-phase hydrogenation conditions at atmospheric pressure revealed a poorer performance, with FA as the main product.

Recent Advances in Reductive Upgrading of 5-Hydroxymethylfurfural via Heterogeneous Thermocatalysis

The catalytic conversion of 5-hydroxymethylfufural (HMF), one of the vital platform chemicals in biomass upgrading, holds great promise for producing highly valuable chemicals through sustainable routes, thereby alleviating the dependence on fossil feedstocks and reducing CO₂ emissions. The reductive upgrading (hydrogenation, hydrogenolysis, ring-opening, ring-rearrangement, amination, etc.) of HMF has exhibited great potential to produce monomers, liquid fuel additives, and other valuable chemicals. Thermocatalytic conversion has a significant advantage over photocatalysis and electrocatalysis in productivity. In this Review, the recent achievements of thermo-reductive transformation of HMF to various chemicals using heterogeneous catalytic systems are presented, including the catalytic systems (catalyst and solvent), reaction conditions, (reaction temperature, pressure, etc.), and reaction mechanisms. The current challenges and future opportunities are discussed as well, aiming at guiding the catalyst design and practical scalable productions.

Ni-Cu/Al2O3 from Layered Double Hydroxides Hydrogenates Furfural to Alcohols

The hydrogenation of furfural is an important process in the synthesis of bio-based chemicals. Copper-based catalysts favor the hydrogenation of furfural to alcohols. Catalytic activity and stability were higher at a Ni-to-Cu atomic ratio of 1:1 and 1.5:0.5 compared to 0.5:1.5. Here, we prepared Ni-Cu/Al2O3 hydrogenation catalysts derived from layered double hydroxides (LDHs). Catalysts calcined at 673 K and reduced at 773 K with nominal Ni/Cu atomic ratios y/x = 1.5/0.5, 1/1 and 0.5/1.5 were characterized by XRD, FESEM-EDX, H2-TPR, XPS, FAA and BET. Their activity was tested at 463 K and in a 0.05 g g−1 furfural solution in ethanol, and the space velocity in a packed-bed reactor (PBR) was 2.85 gFF gcat−1 h−1. In a slurry reactor (SSR) at 5 MPa H2 and a contact time of 4 h, conversion was complete, while it varied from 91 to 99% in the PBR. Tetrahydrofurfuryl alcohol (TFA) was the main product in the SSR, with a selectivity of 32%, 63% and 56% for Ni0.5Cu1.5Al1, Ni1Cu1Al1 and Ni1.5Cu0.5Al1, respectively. The main product in the atmospheric PBR was furfuryl alcohol (FA), with a selectivity of 57% (Ni0.5Cu1.5Al1), 61% (Ni1Cu1Al1) and 58% (Ni1.5Cu0.5Al1). Other products included furan, methylfuran, 1-butanol and 1,2-pentanediol. Ethyl tetrahydrofurfuryl ether and difurfuryl ether were also formed via the nucleophilic addition of furfural with ethanol and furfuryl alcohol.

Biomass-derived chemical substitutes for bisphenol A: recent advancements in catalytic synthesis

Bisphenol A is an oil-derived, large market volume chemical with a wide spectrum of applications in plastics, adhesives and thermal papers. However, bisphenol A is not considered safe due to its endocrine disrupting properties and reproductive toxicity. Several functional substitutes of bisphenol A have been proposed in the literature, produced from plant biomass. Unless otherwise specified, the present review covers the most significant contributions that appeared in the time span January 2015-August 2019, describing the sustainable catalytic synthesis of rigid diols from biomass derivatives. The focus is thereupon on heterogeneous catalysis, use of green solvents and mild conditions, cascade processes in one-pot, and continuous flow setups. More than 500 up-to-date references describe the various substitutes proposed and the catalytic methods for their manufacture, broken down according to the main biomass types from which they originate.

Density Functional Investigation of the Conversion of Furfural to Furfuryl Alcohol by Reaction with i-Propanol over UiO-66 Metal-Organic Framework

Carbonyl C═O bond reduction via catalytic transfer hydrogenation (CTH) is one of the essential processes for biomass conversion to valuable chemicals and fuels. Here, we investigate the CTH of furfural to furfuryl alcohol with i-propanol on UiO-66 metal-organic frameworks using density functional theory calculations and linear scaling relations. Initially, the reaction over two defect sites presented on Zr-UiO-66, namely, dehydrated and hydrated sites, have been compared. The hydrated active site is favored over that on the dehydrated active site since the activation free energy of the rate-determining reaction step occurring on the hydrated active site is lower than that occurring on the dehydrated active site (14.9 vs 17.9 kcal/mol). The catalytic effect of exchanged tetravalent metals (Hf and Ti) on Zr-UiO-66 is also considered. We found that Hf-UiO-66 (13.5 kcal/mol) provides a lower activation energy than Zr-UiO-66 (14.9 kcal/mol) and Ti-UiO-66 (19.4 kcal/mol), which corresponds to it having a higher Lewis acidity. The organic linkers of UiO-66 MOFs play a role in stabilizing all of the species on potential energy surfaces. The linear scaling relationship also reveals the significant role of the UiO-66 active site in activating the carbonyl C═O of furfural, and strong relationships are observed between the activation free energy, the charge of the metal at the MOF active sites, and the complexation energies in reaction coordinates.

Earth-abundant 3d-transition-metal catalysts for lignocellulosic biomass conversion

Transformation of biomass to chemicals and fuels is a long-term goal in both science and industry. However, high cost is one of the major obstacles to the industrialization of this sustainable technology. Thus, developing catalysts with high activity and low-cost is of great importance for biomass conversion. The last two decades have witnessed the increasing achievement of the use of earth-abundant 3d-transition-metals in catalysis due to their low-cost, high efficiency and excellent stability. Here, we aim to review the fast development and recent advances of 3d-metal-based catalysts including Cu, Fe, Co, Ni and Mn in lignocellulosic biomass conversion. Moreover, present research trends and invigorating perspectives on future development are given.

Recent catalytic routes for the preparation and the upgrading of biomass derived furfural and 5-hydroxymethylfurfural

Furans represent one of the most important classes of intermediates in the conversion of non-edible lignocellulosic biomass into bio-based chemicals and fuels. At present, bio-furan derivatives are generally obtained from cellulose and hemicellulose fractions of biomass via the acid-catalyzed dehydration of their relative C6-C5 sugars and then converted into a wide range of products. Furfural (FUR) and 5-hydroxymethylfurfural (HMF) are surely the most used furan-based feedstocks since their chemical structure allows the preparation of various high-value-added chemicals. Among several well-established catalytic approaches, hydrogenation and oxygenation processes have been efficiently adopted for upgrading furans; however, harsh reaction conditions are generally required. In this review, we aim to discuss the conversion of biomass derived FUR and HMF through unconventional (transfer hydrogenation, photocatalytic and electrocatalytic) catalytic processes promoted by heterogeneous catalytic systems. The reaction conditions adopted, the chemical nature and the physico-chemical properties of the most employed heterogeneous systems in enhancing the catalytic activity and in driving the selectivity to desired products are presented and compared. At the same time, the latest results in the production of FUR and HMF through novel environmental friendly processes starting from lignocellulose as well as from wastes and by-products obtained in the processing of biomass are also overviewed.

Heterogeneous Catalytic Upgrading of Biofuranic Aldehydes to Alcohols

Heterogeneous catalytic conversion of lignocellulosic components into valuable chemicals and biofuels is one of the promising ways for biomass valorization, which well meets green chemistry metrics, and can alleviate environmental and economic issues caused by the rapid depletion of fossil fuels. Among the identified biomass derivatives, furfural (FF) and 5-hydroxymethylfurfural (HMF) stand out as rich building blocks and can be directly produced from pentose and hexose sugars, respectively. In the past decades, much attention has been attracted to the selective hydrogenation of FF and 5-hydroxymethylfurfural using various heterogeneous catalysts. This review evaluates the recent progress of developing different heterogeneous catalytic materials, such as noble/non-noble metal particles, solid acids/bases, and alkali metal salts, for the efficient reduction of bio-based furanic aldehydes to alcohols. Emphasis is laid on the insights and challenges encountered in those biomass transformation processes, along with the focus on the understanding of reaction mechanisms to clarify the catalytic role of specific active species. Brief outlook is also made for further optimization of the catalytic systems and processes for the upgrading of biofuranic compounds.