In situ synthesis of magnesium-doped hydroxyapatite aerogel for highly efficient U(VI) separation with ultra high adsorption capacity and excellent recyclability

Mg-doped HAP aerogel (MHAPA) was firstly in situ prepared via freeze-drying-calcination technology to capture U(VI). The U(VI) removal capacity by MHAPA even arrived 2685.6 mg g^-1, which was about 2 times over purchased HAP, illustrating that the incorporation of Mg ions could greatly enhance the U(VI) removal capacity. Compared with HAP, MHAPA also showed better anti-ion interference ability and dynamic removal performances. In comparison with other HAP-based adsorbents, MHAPA possessed good recyclability and its desorption rate was up to 93.4% in the first cycle. The excellent U(VI) removal performances of MHAPA might be owing to its low crystallinity and grain size, fast ion exchange rate and partial ionization under acidic conditions, which would accelerate the process of electrostatic attraction, ion-exchange, and complexation to immobilize U(VI). To sum up, the prepared MHAPA was expected to be an environmentally friendly, recyclable and effective adsorbent to immobilize U(VI) in actual wastewater.

Essence of hydroxyapatite in defluoridation of drinking water: A review

Hydroxyapatite (HAP) is an easily synthesizable, low-cost mineral that has been recognized as a potential material for fluoride removal. Some of the synthesis methods of HAP are quite straightforward and cost-effective, while some require sophisticated synthesis techniques under advanced laboratory conditions. This review assesses the physicochemical characteristics of HAP and HAP-based composites produced via various techniques, their recent development in defluoridation and most importantly, the fluoride removal performances. For the first time, fluoride removal performances of HAP and HAP composites are compared based on partition coefficient (K_D) instead of maximum adsorption capacity (Q_max), which is significantly influenced by initial loading concentrations. Novel HAP tailored composites exhibit comparatively high K_D values indicating the excellent capability of fluoride removal along with specific surface areas above 120 m²/g. HAP doped with aluminium complexes, HAP doped ceramic beads, HAP-pectin nanocomposite and HAP-stilbite nanocomposite, HAP decorated nanotubes, nanowires and nanosheets demonstrated high Q_max and K_D. The secret of HAP is not the excellent fluoride removal performances but best removal at neutral and near-neutral pH, which most of the defluoridation materials are incapable of, making them ideal adsorbents for drinking water treatment. Multiple mechanisms including physical surface adsorption, ion-exchange, and electrostatic interactions are the main mechanisms involved in defluoridation. Further research work must be focused on upscaling HAP-based composites for defluoridation on a commercial scale.

Photoactivatable carbon dots as a label-free fluorescent probe for picric acid detection and light-induced bacterial inactivation

The zero-dimensional carbon nanostructure known as carbon dots showed attractive attributes such as multicolour emission, very high quantum yield, up-conversion, very good aqueous solubility, eco-friendliness, and excellent biocompatibility. These outstanding features of the carbon dots have raised significant interest among the research community worldwide. In the current work, water-soluble nitrogen, silver, and gold co-doped bimetallic carbon dots (BCDs) were prepared using the one-pot hydrothermal method with citric acid as a sole carbon source. As prepared BCDs showed size in the range of 4-8 nm and excitation-independent emission behaviour with maximum emission observed at 427 nm. Additionally, these BCDs showed a very high quantum yield value of 50% and fluorescence lifetime value of 10.1 ns respectively. Interestingly, as prepared BCDs selectively sense picric acid (PA) by exhibiting "selective fluorescence turn-off" behaviour in the presence of PA with a limit of detection value (LOD) of 46 nM. Further, as prepared BCDs were explored for photodynamic therapy to inactivate bacterial growth in the presence of light (400-700 nm) by generating singlet oxygen. Thus as prepared BCDs offer lots of potentials to use a nanoprobe to detect picric acid in an aqueous medium and to design next-generation antibacterial materials.

Comparison of Water Defluoridation Using Different Techniques

Fluoride pollution in subsurface water is a significant problem for different nations across the world because of the intake of excessive fluoride caused by the drinking of the contaminated subsurface. Water pollution by flouride can be attributed to the natural and human-made agents. Increased levels of fluoride in drinking water may result in the irretrievable demineralization of bone and tooth tissues, a situation called fluorosis, and other disorders. There has long been a need for fluoride removal from drinking water to make it safe for human use. Among the various fluoride removal methods, adsorption is the method most popularly used due to its cheap cost, ease of utilization, and being a scalable and simple physical technique. According to the findings of this study, the highest concentration of fluoride (0.1–15.0 mg/L) was found in Sweden and the lowest (0.03–1.14 mg/L) in Italy. We collected the values of adsorption capacities and fluoride removal efficiencies of various types of adsorbents from valuable released data accessible in the literature and exhibited tables. There is still a need to find the actual possibility of using biosorbents and adsorbents on a commercial scale and to define the reusability of adsorbents to decrease price and the waste generated from the adsorption method. This article reviews the currently available methods and approaches to fluoride removal of water.

Biopolymer-Based Nanohydroxyapatite Composites for the Removal of Fluoride, Lead, Cadmium, and Arsenic from Water

In this study, hydroxyapatite (HAP) nanocomposites were prepared with chitosan (HAP-CTS), carboxymethyl cellulose (HAP-CMC), alginate (HAP-ALG), and gelatin (HAP-GEL) using a simple wet chemical in situ precipitation method. The synthesized materials were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, Brunauer-Emmett-Teller surface area analysis, and thermogravimetric analysis. This revealed the successful synthesis of composites with varied morphologies. The adsorption abilities of the materials toward Pb(II), Cd(II), F-, and As(V) were explored, and HAP-CTS was found to have versatile adsorption properties for all of the ions, across a wide range of concentrations and pH values, and in the presence of common ions found in groundwater. Additionally, X-ray photoelectron spectroscopy and energy-dispersive X-ray spectroscopy confirmed the affinity of HAP-CTS toward multi-ion mixture containing all four ions. HAP-CTS was hence engineered into a more user-friendly form, which can be used to form filters through its combination with cotton and granular activated carbon. A gravity filtration study indicates that the powder form of HAP-CTS is the best sorbent, with the highest breakthrough capacity of 3000, 3000, 2600, and 2000 mL/g for Pb(II), Cd(II), As(V), and F-, respectively. Hence, we propose that HAP-CTS could be a versatile sorbent material for use in water purification.

On the Crystallization of Hydroxyapatite under Hydrothermal Conditions: Role of Sebacic Acid as an Additive

Hydroxyapatite (HAp) is a major inorganic component in bone minerals and is often used for bone tissue engineering. Herein, we synthesized HAp using sebacic acid as an additive at different pH values by a hydrothermal method. Sebacic acid, which has two carboxyl group ends of the carbonate chain, binds with Ca ions during the hydrothermal process to become a crystal nucleation site in (001) and at the same time could act as an inhibitor in a specific direction [i.e., (110)] for the HAp crystal growth. Sebacic acid and the hydroxyl ion (OH^-) are competitively attracted to the a(b)-plane of HAp. Depending on the pH condition, the crystal growth resulted in different morphologies depending on the ratio of sebacic acid and hydroxide ions. It was confirmed through Fourier-transform infrared spectroscopy and Raman spectroscopy that dicalcium phosphate anhydrous with HPO₄ was produced under acidic conditions and HAp was produced under neutral and basic conditions. The plate- and nanorod-HAp crystals' preferential growth along the c-axis, which were obtained under neutral and basic conditions, was analyzed by transmission electron microscopy. Growth control in the c-axis direction of HAp is necessary for the understanding of crystallization of bone minerals because the mineral inside the collagen fibrils in bone tissue also shows a c-axis orientation.

Effect of LDHs and Other Clays on Polymer Composite in Adsorptive Removal of Contaminants: A Review

Recently, the development of a unique class of layered silicate nanomaterials has attracted considerable interest for treatment of wastewater. Clean water is an essential commodity for healthier life, agriculture and a safe environment at large. Layered double hydroxides (LDHs) and other clay hybrids are emerging as potential nanostructured adsorbents for water purification. These LDH hybrids are referred to as hydrotalcite-based materials or anionic clays and promising multifunctional two-dimensional (2D) nanomaterials. They are used in many applications including photocatalysis, energy storage, nanocomposites, adsorption, diffusion and water purification. The adsorption and diffusion capacities of various toxic contaminants heavy metal ions and dyes on different unmodified and modified LDH-samples are discussed comparatively with other types of nanoclays acting as adsorbents. This review focuses on the preparation methods, comparison of adsorption and diffusion capacities of LDH-hybrids and other nanoclay materials for the treatment of various contaminants such as heavy metal ions and dyes.

A novel nanobiosorbent of functionalized graphene quantum dots from rice husk with barium hydroxide for microwave enhanced removal of lead (II) and lanthanum (III)

In this study, rice husk was used as a sustainable source to synthesize graphene quantum dots (GQDOs) with 2D morphology. Chemical modification of GQDOs with Ba(OH)₂ was followed to form a novel GQDOs-Ba nanobiosorbent with an increased number of surface hydroxyl groups. The physicochemical properties of GQDOs and GQDOs-Ba were investigated by FT-IR, SEM, TEM, TGA, and XRD. The adsorption parameters of Pb(II) and La(III) onto GQDOs-Ba were optimized using microwave sorption approach. The maximum capacity reached 3400 µmol g^-1 (pH 7), and 1500 µmol g^-1 (pH 5) at 15 s for Pb(II) and La(III), respectively. The adsorption isotherm models by GQDOs-Ba fitted well with Langmuir. The pseudo-second order was agreed by Pb(II) and La(III) ions. The thermodynamic studies elucidated that Pb(II) and La(III) adsorption onto GQDOs-Ba followed a spontaneous model. The GQDOs-Ba nanobiosorbent accomplished excellent removal percentages from different water samples containing lead (98.5%-99.8%) and lanthanum (94.6%-96.2%).

Dicarboxylic acid cross-linked metal ion decorated bentonite clay and chitosan for fluoride removal studies

This study focused on the synthesis of a dicarboxylic acid (malic acid (A)), metal ion decorated bentonite clay (BC) modified with chitosan (CS) and the investigation of its defluoridation efficiency in fluoride contaminated groundwater. The synthesized adsorbent showed a fluoride removal capacity of 9.87 mg g⁻¹. Batch adsorption studies were conducted to establish the effect of various parameters such as contact time, pH, initial concentration, and competitor ions. The adsorption isotherms of Freundlich, Dubinin–Radushkevich, and Langmuir were studied and the Freundlich isotherm fitted the data well. Kinetic studies showed that the adsorption process follows pseudo second order kinetics. Thermodynamic studies revealed that the fluoride adsorption process is spontaneous and endothermic. Reuse and regeneration studies were executed for effective application of the nanocomposite. The synthesized adsorbent also has potential for real water treatment applications.

The adsorbent CeBC-A@CS nanocomposite has the maximum fluoride adsorption capacity.

Enhanced fluoride removal from water by rare earth (La and Ce) modified alumina: Adsorption isotherms, kinetics, thermodynamics and mechanism

The removal of F^- from aqueous solution using lanthanum and cerium modified mesoporous alumina (La/MA and Ce/MA) was studied, and characteration of the adsorbents by XRD, BET, XRF, FTIR, TEM, XPS and the pH_ZPC measurements were carried out. The adsorption was investigated in both batch and column adsorption systems. Batch experimental results showed that adsorption capacities of adsorbents were recorded in the following order: La/MA > Ce/MA > mesoporous alumina (MA). Besides, adsorption datas were fitted well by Sips isotherm model and Elovich kinetics model, and the maximum adsorption capacity of La/MA was 26.45 mg·g^-1 in Sips model at the dosage of 2.0 g·L^-1 and near neutral condition (pH = 6.0 ± 0.1). Moreover, thermodynamic parameters were illustrated that adsorption process of fluoride ion over La/MA was spontaneous and endothermic. In the adsorption process, the interaction between metal and fluoride, the adsorption capacity was increased due to form the bond of M···F (M = La or Ce). Furthermore, the influence of coexisted anions on F^- removal was investigated, and it was indicated that removal efficiency was slightly affected by the presence of Cl^- and NO₃^-, while SO₄^2- and CO₃^2- caused a sharp fall in removal efficiency. Column experiments results were indicated that time of break-through of La/MA was twice as much as that of MA.

Antimicrobial and biodegradable chitosan/cellulose acetate phthalate/ZnO nano composite films with optimal oxygen permeability and hydrophobicity for extending the shelf life of black grape fruits

Film-forming biopolymers possessing antimicrobial activity and biodegradability are of great interest on account of their potential use in food packaging applications. The present study deals with the fabrication and characterisation of chitosan (CS) - cellulose acetate phthalate (CAP) films incorporated with ZnO nanoparticles (nano ZnO). CS-CAP films with varying ratios of nano ZnO reinforcement were prepared by solvent casting method. The thermal stability and barrier properties of the fabricated films increased with increasing amount of nano ZnO in the range of 2-7.5% (w/w). CS-CAP film loaded with 5% (w/w) nano ZnO showed the most optimal tensile strength and stiffness to be utilized as a food packaging material. Water contact angle measurements showed the prepared nano composite films to have low surface wettability and high contact angle value up to 90°. Biodegradability of the nano composite films ranged from 30 to 50% in 28 days. The CS-CAP film loaded with 5% (w/w) nano ZnO had extended the shelf life of black grape fruits up to 9 days. The demonstrated barrier and food protection characteristics of the CS-CAP-ZnO films attested its suitability as a primary food packaging material that can be used to increase the shelf life of black grape fruits.

Improved nanocomposite of montmorillonite and hydroxyapatite for defluoridation of water

A novel hydroxyapatite montmorillonite (HAP-MMT) nanocomposite system was synthesized using a simple wet chemical in situ precipitation method. Neat nano hydroxyapatite (HAP) was also synthesized for comparison. The characterization of the materials was carried out using Fourier Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and Brunauer–Emmett–Teller (BET) isotherms to study the functional groups, morphology, crystallinity and the surface area respectively. Batch adsorption studies and kinetic studies on fluoride adsorption were conducted for the HAP-MMT system and for neat HAP. The effect of parameters such as contact time, pH, initial concentration, temperature, and thermodynamic parameters and the effect of coexisting ions on fluoride adsorption by HAP-MMT were studied. Results of the isotherm experiments were fitted to four adsorption isotherm models namely Langmuir, Freundlich, Temkin and Dubinin Radushkevich. Fluoride adsorption over HAP-MMT fitted to the Freundlich adsorption isotherm model and showed more than two-fold improved adsorption capacity (16.7 mg g⁻¹) compared to neat HAP. The best-fitting kinetic model for both adsorbents was found to be pseudo second order. Calculated thermodynamic parameters indicated that the fluoride adsorption by HAP-MMT is more favorable compared to that on HAP within the temperature range of 27 °C–60 °C. Improved fluoride adsorption by HAP-MMT is attributed to the exfoliated nature of HAP-MMT. Gravity filtration studies carried out using a 1.5 ppm fluoride solution, which is closer to the ground water fluoride concentrations of Chronic Kidney Disease of unknown etiology (CKDu) affected areas in Sri Lanka, resulted in a 1600 ml g⁻¹ break through volume indicating the potential of HAP-MMT to be used in real applications.

A novel hydroxyapatite montmorillonite (HAP-MMT) nanocomposite was synthesized using a simple wet chemical in situ precipitation method. This nanocomposite showed improved adsorption properties towards fluoride ions in water.