Unveiling the Electrolyte Cations Dependent Kinetics on CoOOH-Catalyzed Oxygen Evolution Reaction

The electrolyte cations-dependent kinetics have been widely observed in many fields of electrocatalysis, however, the exact mechanism of the influence on catalytic performance is still a controversial topic of considerable discussion. Herein, combined with operando X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM), we verify that the electrolyte cations could intercalate into the layer of pristine CoOOH catalyst during the oxygen evolution reaction (OER) process, while the bigger cations lead to enlarged interlayer spacing and increased OER activity, following the order Cs+ >K+ >Na+ >Li+ . X-ray absorption spectroscopy (XAS), in situ Raman, in situ Ultraviolet-visible (UV/Vis) spectroscopy, in situ XAS spectroscopy, cyclic voltammetry (CV), and theoretical calculations reveal that the intercalation of electrolyte cations efficiently modify the oxidation states of Co by enlarging the Co-O bonds, which in turn enhance the d-band center of Co, optimize the adsorption strength of oxygen intermediates, facilitate the formation of OER active Co(IV) species, and reduce the energy barrier of the rate-determing step (RDS), thereby enhancing the OER activity. This work not only provides an informative picture to understand the complicated dependence of OER kinetics on electrolyte cations, but also sheds light on understanding the mechanism of other electrolyte cation-targeted electrocatalysis.

The Review of Hybridization of Transition Metal-Based Chalcogenides for Lithium-Ion Battery Anodes

Transition metal chalcogenides as potential anodes for lithium-ion batteries have been widely investigated. For practical application, the drawbacks of low conductivity and volume expansion should be further overcome. Besides the two conventional methods of nanostructure design and the doping of carbon-based materials, the component hybridization of transition metal-based chalcogenides can effectively enhance the electrochemical performance owing to the synergetic effect. Hybridization could promote the advantages of each chalcogenide and suppress the disadvantages of each chalcogenide to some extent. In this review, we focus on the four different types of component hybridization and the excellent electrochemical performance that originated from hybridization. The exciting problems of hybridization and the possibility of studying structural hybridization were also discussed. The binary and ternary transition metal-based chalcogenides are more promising to be used as future anodes of lithium-ion batteries for their excellent electrochemical performance originating from the synergetic effect.

High Cycle Stability of Hybridized Co(OH)2 Nanomaterial Structures Synthesized by the Water Bath Method as Anodes for Lithium-Ion Batteries

Cobalt oxides have been intensely explored as anodes of lithium-ion batteries to resolve the intrinsic disadvantages of low electrical conductivity and volume change. However, as a precursor of preparing cobalt oxides, Co(OH)₂ has rarely been investigated as the anode material of lithium-ion batteries, perhaps because of the complexity of hydroxides. Hybridized Co(OH)₂ nanomaterial structures were synthesized by the water bath method and exhibited high electrochemical performance. The initial discharge and charge capacities were 1703.2 and 1262.9 mAh/g at 200 mA/g, respectively. The reversible capacity was 1050 mAh/g after 150 cycles. The reversible capability was 1015 mAh/g at 800 mA/g and increased to 1630 mAh/g when driven back to 100 mA/g. The electrochemical reaction kinetics study shows that the lithium-ion diffusion-controlled contribution is dominant in the energy storage mechanism. The superior electrochemical performance could result from the water bath method and the hybridization of nanosheets and nanoparticles structures. These hybridized Co(OH)₂ nanomaterial structures with high electrochemical performance are promising anodes for lithium-ion batteries.

Nanocrystalline Cellulose Supported MnO2 Composite Materials for High-Performance Lithium-Ion Batteries

The rate capability and poor cycling stability of lithium-ion batteries (LIBs) are predominantly caused by the large volume expansion upon cycling and poor electrical conductivity of manganese dioxide (MnO₂), which also exhibits the highest theoretical capacity among manganese oxides. In this study, a nanocomposite of nanosized MnO₂ and pyrolyzed nanocrystalline cellulose (CNC) was prepared with high electrical conductivity to enhance the electrochemical performance of LIBs. The nanocomposite electrode showed an initial discharge capacity of 1302 mAh g⁻¹ at 100 mA g⁻¹ and exhibited a high discharge capacity of 305 mAh g⁻¹ after 1000 cycles. Moreover, the MnO₂-CNC nanocomposite delivered a good rate capability of up to 10 A g⁻¹ and accommodated the large volume change upon repeated cycling tests.

Synthesis of Si/Fe2O3-Anchored rGO Frameworks as High-Performance Anodes for Li-Ion Batteries

By virtue of the high theoretical capacity of Si, Si-related materials have been developed as promising anode candidates for high-energy-density batteries. During repeated charge/discharge cycling, however, severe volumetric variation induces the pulverization and peeling of active components, causing rapid capacity decay and even development stagnation in high-capacity batteries. In this study, the Si/Fe2O3-anchored rGO framework was prepared by introducing ball milling into a melt spinning and dealloying process. As the Li-ion battery (LIB) anode, it presents a high reversible capacity of 1744.5 mAh g-1 at 200 mA g-1 after 200 cycles and 889.4 mAh g-1 at 5 A g-1 after 500 cycles. The outstanding electrochemical performance is due to the three-dimensional cross-linked porous framework with a high specific surface area, which is helpful to the transmission of ions and electrons. Moreover, with the cooperation of rGO, the volume expansion of Si is effectively alleviated, thus improving cycling stability. The work provides insights for the design and preparation of Si-based materials for high-performance LIB applications.

Synthesis and electrochemical performance of hollow-structured NiO + Ni nanofibers wrapped by graphene as anodes for Li-ion batteries

Hollow-structured NiO + Ni nanofibers wrapped by graphene were designed and successfully fabricated via a simple method. First, solid NiO + Ni nanofibers were prepared by electrospinning followed by calcination. Here, a portion of the metallic Ni was retained to improve the electrochemical performance of NiO by adjusting the calcination temperature. Next, the nanofibers were thoroughly mixed with different amounts of graphene and calcinated once more to form hollow-structured NiO + Ni nanofibers with an extremely high specific surface via the reaction between graphene and NiO on the nanofiber surface and subsequent migration of NiO into the nanofibers. Results showed that the obtained hollow-structured NiO + Ni electrode demonstrates optimal electrochemical performance when the graphene content is controlled to 3 wt%. The first cycle discharge/charge specific capacity of the electrode peaked (1596/1181 mAh · g^-1) at 100 mA · g^-1, with a coulombic efficiency of approximately 74% (60% for 0 wt% graphene, 65% for 1 wt% graphene, and 51% for 4 wt% graphene). It also presented excellent cycling stability after 100 cycles at 100 mA · g^-1on account of its high retained discharge specific capacity (251 mAh · g^-1for 0 wt% graphene, 385 mAh · g^-1for 1 wt% graphene, 741 mAh · g^-1for 3 wt% graphene, and 367 mAh · g^-1for 4 wt% graphene). Moreover, the synthesized electrode possessed outstanding rate capability owing to its large average discharge specific capacity of approximately 546 mAh · g^-1(45 mAh · g^-1for 0 wt% graphene, 256 mAh · g^-1for 1 wt% graphene, and 174 mAh · g^-1for 4 wt% graphene) from 100 mA · g^-1to 2000 mA · g^-1. The observed improvement in electrochemical performance could be attributed to the increase in active sites and decrease in charge transport distance in the hollow-structured NiO + Ni nanofibers. Excessive introduction of graphene caused a sharp loss in electrochemical performance due to the agglomeration of graphene sheets on the nanofiber surfaces.

Intrinsic Oxidase-like Nanoenzyme Co4S3/Co(OH)2 Hybrid Nanotubes with Broad-Spectrum Antibacterial Activity

Improving the antibacterial activity of nanomaterials and avoiding the use of H₂O₂ are vital for biosecurity and public health. In this work, novel Co₄S₃/Co(OH)₂ hybrid nanotubes (HNTs) for the first time were successfully synthesized through the control of Na₂S treatment of Co(CO₃)_0.35Cl_0.20(OH)_1.10 precursor. On the basis of Kirkendall effect, acicular precursor was vulcanized to form Co₄S₃/Co(OH)₂ HNTs that possess great properties including favorable storage ability and ideal stability. By tailoring the composition and structure, Co₄S₃/Co(OH)₂ HNTs were found to have profound oxidase-like catalytic activities. When pH = 3 precursor was treated with 900 mg of Na₂S, Co₄S₃/Co(OH)₂ HNTs exhibit superior performance. Owing to the outstanding oxidase-like activity, Co₄S₃/Co(OH)₂ HNTs can eliminate Escherichia coli, Pseudomonas aeruginosa, Staphylococcus sciuri, and Bacillus without the help of H₂O₂. It turned out that the sterilization ability came from the superoxide anion radical generated by Co₄S₃/Co(OH)₂ HNTs. With Co₄S₃/Co(OH)₂ HNTs, the intracellular reactive oxygen species level can be enhanced and the toxicity of H₂O₂ can be absolutely avoided. Overall, the synthesis of antibacterial nanomaterials is unparalleled and the results of this work would facilitate the utilization in medical science, new energy, and environmental catalysis.

Binder-Free Electrodes and Their Application for Li-Ion Batteries

Lithium-ion batteries (LIB) as energy supply and storage systems have been widely used in electronics, electric vehicles, and utility grids. However, there is an increasing demand to enhance the energy density of LIB. Therefore, the development of new electrode materials with high energy density becomes significant. Although many novel materials have been discovered, issues remain as (1) the weak interaction and interface problem between the binder and the active material (metal oxide, Si, Li, S, etc.), (2) large volume change, (3) low ion/electron conductivity, and (4) self-aggregation of active materials during charge and discharge processes. Currently, the binder-free electrode serves as a promising candidate to address the issues above. Firstly, the interface problem of the binder and active materials can be solved by fixing the active material directly to the conductive substrate. Secondly, the large volume expansion of active materials can be accommodated by the porosity of the binder-free electrode. Thirdly, the ion and electron conductivity can be enhanced by the close contact between the conductive substrate and the active material. Therefore, the binder-free electrode generally exhibits excellent electrochemical performances. The traditional manufacture process contains electrochemically inactive binders and conductive materials, which reduces the specific capacity and energy density of the active materials. When the binder and the conductive material are eliminated, the energy density of the battery can be largely improved. This review presents the preparation, application, and outlook of binder-free electrodes. First, different conductive substrates are introduced, which serve as carriers for the active materials. It is followed by the binder-free electrode fabrication method from the perspectives of chemistry, physics, and electricity. Subsequently, the application of the binder-free electrode in the field of the flexible battery is presented. Finally, the outlook in terms of these processing methods and the applications are provided.

Birnessite based nanostructures for supercapacitors: challenges, strategies and prospects

In the past few years, intensive attention has been focused on birnessite based electrodes for supercapacitors. Much progress has been achieved in developing birnessite based nanostructures with high electrochemical performance. However, challenges still remain in taking full advantage of birnessite and building smart structures to overcome the gap between the obtained capacitance and its theoretical capacitance. In this review, the basic information on birnessite and its preparation strategies are summarized and the current challenges are put forward. Finally, some new strategies for preparing high electrochemical performance birnessite based nanostructures are highlighted.

Three-dimensional porous Co3O4-CoO@GO composite combined with N-doped carbon for superior lithium storage

Transition metal oxides (TMOs) as anode materials have potential for lithium-ion batteries (LIBs). However, the poor rate capacity and cycle stability restrict its application. Herein, we demonstrate a facile one-step hydrothermal method to construct a three-dimensional porous conductive network structure, which consists of thin-layered graphene, ultrafine Co₃O₄-CoO nanoparticles and nitrogen-doped carbon. This unique structure can effectively prevent particle agglomeration and cracking caused by volume expansion, provide fast passage for lithium ion/electron transport during cycling and improve the electrical conductivity of the electrode. Moreover, the electrochemical kinetic analysis proves that this is a process dominated by pseudocapacitive behavior. Consequently, the N-C@Co₃O₄-CoO@GO hybrid electrode delivers an ultrahigh capacity of 1 273.1 mA h g^-1 at 0.1 A g^-1 and superior rate performance (725.1 mA h g^-1 at 5 A g^-1). Additionally, it exhibits a high reversible cycling capacity of 787.4 mA h g^-1 at 1 A g^-1 over 600 cycles and even maintains excellent cycling stability for a ultra-long cycles at 5 A g^-1. This work provides a feasible strategy for fabricating the N-C@Co₃O₄-CoO@GO composite as a promising high-performance TMOs anode for LIBs.

LiMnPO4-olivine deposited on a nanoporous alloy as an additive-free electrode for lithium ion batteries

A new strategy for the fabrication of binder- and carbon-free electrodes for lithium ion batteries is demonstrated.