Superior stability of a bifunctional oxygen electrode for primary, rechargeable and flexible Zn-air batteries

A primary battery for efficient cadmium contamination remediation and electricity generation

In this work, two kinds of primary batteries, both of which included a Zn anode, C rod cathode, copper wire and electrolyte composed of Cd2+-contaminated water or soil, were constructed in the first attempt to both remove Cd2+ and generate electricity. Unlike traditional technologies such as electrokinetic remediation with high energy consumption, this technology could realize Cd2+ migration to aggregation and solidification and generate energy at the same time through simultaneous galvanic reactions. The passive surface of Zn and C was proven via electrochemical measurements to be porous to maintain the relatively active galvanic reactions for continuous Cd2+ precipitation. Cd2+ RE (removal efficiency) and electricity generation were investigated under different conditions, based on which two empirical models were established to predict them successfully. In soil, KCl was added to desorb Cd2+ from soil colloids to promote Cd2+ removal. These systems were also proven to remove Cd2+ efficiently when their effects on plants, zebrafish, and the soil bacterial community were tested. LEDs could be lit for days by utilizing the electricity produced herein. This work provides a novel, green, and low-cost route to remediate Cd2+ contamination and generate electricity simultaneously, which is of extensive practical significance in the environmental and energy fields.

Investigation of Highly Active Carbon-, Cobalt-, and Noble Metal-Free MnO2/NiO/Ni-Based Bifunctional Air Electrodes for Metal-Air Batteries with an Alkaline Electrolyte

Compared to other battery technologies, metal-air batteries offer high specific capacities because the active material at the cathode side is supplied by ambient atmosphere. To secure and further extend this advantage, the development of highly active and stable bifunctional air electrodes is currently the main challenge that needs to be resolved. Herein, a highly active carbon-, cobalt-, and noble-metal-free MnO₂/NiO-based bifunctional air electrode is presented for metal-air batteries in alkaline electrolytes. Notably, while electrodes without MnO₂ reveal stable current densities over 100 cyclic voltammetry cycles, MnO₂ containing samples show a superior initial activity and an elevated open circuit potential. Along this line, the partial substitution of MnO₂ by NiO drastically increases the cycling stability of the electrode. X-ray diffractograms, scanning electron microscopy images, and energy-dispersive X-ray spectra are obtained before and after cycling to investigate structural changes of the hot-pressed electrodes. XRD results suggest that MnO₂ is dissolved or transformed into an amorphous phase during cycling. Furthermore, SEM micrographs show that the porous structure of a MnO₂ and NiO containing electrode is not maintained during cycling.

Opportunities of Flexible and Portable Electrochemical Devices for Energy Storage: Expanding the Spotlight onto Semi-solid/Solid Electrolytes

The ever-increasing demand for flexible and portable electronics has stimulated research and development in building advanced electrochemical energy devices which are lightweight, ultrathin, small in size, bendable, foldable, knittable, wearable, and/or stretchable. In such flexible and portable devices, semi-solid/solid electrolytes besides anodes and cathodes are the necessary components determining the energy/power performances. By serving as the ion transport channels, such semi-solid/solid electrolytes may be beneficial to resolving the issues of leakage, electrode corrosion, and metal electrode dendrite growth. In this paper, the fundamentals of semi-solid/solid electrolytes (e.g., chemical composition, ionic conductivity, electrochemical window, mechanical strength, thermal stability, and other attractive features), the electrode-electrolyte interfacial properties, and their relationships with the performance of various energy devices (e.g., supercapacitors, secondary ion batteries, metal-sulfur batteries, and metal-air batteries) are comprehensively reviewed in terms of materials synthesis and/or characterization, functional mechanisms, and device assembling for performance validation. The most recent advancements in improving the performance of electrochemical energy devices are summarized with focuses on analyzing the existing technical challenges (e.g., solid electrolyte interphase formation, metal electrode dendrite growth, polysulfide shuttle issue, electrolyte instability in half-open battery structure) and the strategies for overcoming these challenges through modification of semi-solid/solid electrolyte materials. Several possible directions for future research and development are proposed for going beyond existing technological bottlenecks and achieving desirable flexible and portable electrochemical energy devices to fulfill their practical applications. It is expected that this review may provide the readers with a comprehensive cross-technology understanding of the semi-solid/solid electrolytes for facilitating their current and future researches on the flexible and portable electrochemical energy devices.

Recent Progress of Non-Noble Metal Catalysts for Oxygen Electrode in Zn-Air Batteries: A Mini Review

Oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) play crucial roles in energy conversion and storage devices. Particularly, the bifunctional ORR/OER catalysts are core components in rechargeable metal–air batteries, which have shown great promise in achieving "carbon emissions peak and carbon neutrality" goals. However, the sluggish ORR and OER kinetics at the oxygen cathode significantly hinder the performance of metal–air batteries. Although noble metal-based catalysts have been widely employed in accelerating the kinetics and improving the bifunctionality, their scarcity and high cost have limited their deployment in the market. In this review, we will discuss the ORR and OER mechanisms, propose the principles for bifunctional electrocatalysts design, and present the recent progress of the state-of-the-art bifunctional catalysts, with the focus on non-noble metal-based materials to replace the noble metal catalysts in Zn–air batteries. The perspectives for the future R&D of bifunctional electrocatalysts will be provided toward high-performance Zn–air batteries at the end of this paper.

N, S-doped hollow carbon nanosheet encapsulated Co9S8 nanoparticles as high-efficient bifunctional electrocatalyst for rechargeable zinc-air battery

The development of non-noble metal-based oxygen reduction/evolution reaction (ORR/OER) bifunctional electrocatalyst with reasonably designed structure and inexpensive component is of practical significance for commercialization of rechargeable zinc-air batteries. Here, we...

In situ coupling of Ag nanoparticles with high-entropy oxides as highly stable bifunctional catalysts for wearable Zn-Ag/Zn-air hybrid batteries

With the combination of the advantages of both Zn-Ag and Zn-air batteries, hybrid Zn-Ag/Zn-air batteries nevertheless suffer greatly from structural instability and activity degradation of the catalysts at the air electrodes. Herein, we introduce a scalable chemical dealloying procedure to synthesize mutually interacting and stable bifunctional catalysts, consisting of imbedded Ag nanoparticles for the oxygen reduction reaction (ORR) and quantitatively designed multicomponent high-entropy oxides (HEOs) for the oxygen evolution reaction (OER). The ORR performance and the Zn-Ag battery capacity can be precisely controlled by the content of Ag nanoparticles. Impressively, with a significantly low Ag content (∼9.13 wt%) in the bifunctional (AlNiCoFeCr)₃O₄/Ag, our hybrid Zn-Ag/Zn-air batteries using such catalysts are able to be continuously charged/discharged for more than 450 h and deliver a high energy density of 810 W h kg^-1. We expect that these stabilized noble metals in HEO nanocomposites may work as multifunctional electrocatalysts in many other energy conversion devices.

Mapping the Design of Electrolyte Materials for Electrically Rechargeable Zinc-Air Batteries

Electrically rechargeable zinc-air batteries (ERZABs) have attracted substantial research interest as one of the best candidate power sources for electric vehicles, grid-scale energy storage, and portable electronics owing to their high theoretical capacity, low cost, and environmental benignity. However, the realization of ERZABs with long cycle life and high energy and power densities is still a considerable challenge. The electrolyte, which serves as the ionic conductor, is one of the core components of ERZABs, as it plays a significant role during the discharge-charge process and greatly influences the rechargeability, operating voltage, lifespan, power density, and safety of ERZABs. Herein, the fundamental electrochemistry of electrolyte materials for ERZABs and the associated challenges are presented. Furthermore, recent advances in electrolyte materials for ERZABs, including alkaline aqueous electrolytes, nonalkaline electrolytes, ionic liquids, and semisolid-state electrolytes are discussed. This work aims to provide insights into the future exploration of high-performance electrolytes and thus promote the development of ERZABs.

Bimetallic Sulfide with Controllable Mg Substitution Anchored on CNTs as Hierarchical Bifunctional Catalyst toward Oxygen Catalytic Reactions for Rechargeable Zinc-Air Batteries

The exploitation of high-efficiency and cheap bifunctional cathode electrocatalyst is of significant importance to rechargeable zinc-air batteries. In this paper, a bimetallic sulfide coupled with a CNT ((Co, Mg)S₂@CNTs) hybrid catalyst is developed via a proposed vulcanization process. The (Co, Mg)S₂@CNTs) with controllable Mg substitution has a tailored crystal structure (amorphous and crystalline), which catalyzes the oxygen reduction/evolution reaction (ORR/OER). The active sites of CoS₂@CNTs are activated by doping Mg ions, which accelerates the kinetics of the oxygen adsorption for ORR and oxygen desorption for OER. Meanwhile, the hybrid catalyst exhibits a unique hierarchal morphology and a "catalytic buffer", which further accelerate the mass transfer of catalytic processes. In addition, the outer wall of CNTs as substrate effectively avoid the agglomeration of (Co, Mg)S₂ particles by reasonably providing adsorption sites. The inner and outer walls of CNTs form a high-speed conduction pathway, quickly transferring the electrons produced by oxygen catalytic reactions. As a result, the (Co, Mg)S₂@CNTs exhibit an ORR performance comparable with commercial catalyst Pt/C-RuO₂ and remarkable OER performance (E_j=10 = 1.59 V). The high power density of 268 mW cm^-2 and long-term charge/discharge stability of the zinc-air battery proves the feasibility of (Co, Mg)S₂@CNTs application in high-power devices.

A database of battery materials auto-generated using ChemDataExtractor

A database of battery materials is presented which comprises a total of 292,313 data records, with 214,617 unique chemical-property data relations between 17,354 unique chemicals and up to five material properties: capacity, voltage, conductivity, Coulombic efficiency and energy. 117,403 data are multivariate on a property where it is the dependent variable in part of a data series. The database was auto-generated by mining text from 229,061 academic papers using the chemistry-aware natural language processing toolkit, ChemDataExtractor version 1.5, which was modified for the specific domain of batteries. The collected data can be used as a representative overview of battery material information that is contained within text of scientific papers. Public availability of these data will also enable battery materials design and prediction via data-science methods. To the best of our knowledge, this is the first auto-generated database of battery materials extracted from a relatively large number of scientific papers. We also provide a Graphical User Interface (GUI) to aid the use of this database.

Synthesis of Ti4O7/Ti3O5 Dual-Phase Nanofibers with Coherent Interface for Oxygen Reduction Reaction Electrocatalysts

Electrocatalysts play an important role in oxygen reduction reaction (ORR) in promoting the reaction process. Although commercial Pt/C exhibits excellent performance in ORR, the low duration, high cost, and poor methanol tolerance seriously restrict its sustainable development and application. Ti_nO_2n-1 (3 ≤ n ≤ 10) is a series of titanium sub-oxide materials with excellent electrical conductivity, electrochemical activity, and stability, which have been widely applied in the field of energy storage and catalysis. Herein, we design and synthesize Ti₄O₇/Ti₃O₅ (T4/T3) dual-phase nanofibers with excellent ORR catalytic performance through hydrothermal growth, which is followed by a precisely controlled calcination process. The H₂Ti₃O₇ precursor with uniform size can be first obtained by optimizing the hydrothermal growth parameters. By precisely controlling the amount of reducing agent, calcination temperature, and holding time, the T4/T3 dual-phase nanofibers with uniform morphology and coherent interfaces can be obtained. The orientation relationships between T4 and T3 are confirmed to be [ 001 ] T 3 / / [ 031 ] T 4 , ( 100 ) T 3 / / ( 92 6 ¯ ) T 4 , and ( 010 ) T 3 / / ( 1 2 ¯ 6 ) T 4 , respectively, based on comprehensive transmission electron microscopy (TEM) investigations. Furthermore, such dual-phase nanofibers exhibit the onset potential and half-wave potential of 0.90 V and 0.75 V as the ORR electrocatalysts in alkaline media, respectively, which illustrates the excellent ORR catalytic performance. The rotating ring-disk electrode (RRDE) experiment confirmed the electron transfer number of 3.0 for such catalysts, which indicates a mixture of two electron and four electron transfer reaction pathways. Moreover, the methanol tolerance and cycling stability of the catalysts are also investigated accordingly.

Pollen-derived porous carbon decorated with cobalt/iron sulfide hybrids as cathode catalysts for flexible all-solid-state rechargeable Zn-air batteries

The development of flexible all-solid-state rechargeable Zn-air batteries (FS-ZABs) for wearable applications faces challenges from the balance between performance and flexibility of the battery; efficient cathode catalyst and reasonable electrode construction design are key factors. Herein, a low-cost pollen derived N,S co-doped porous carbon decorated with Co9S8/Fe3S4 nanoparticle hybrids (Co-Fe-S@NSRPC) has been synthesized. Owing to the active Co9S8/Fe3S4 nanoparticles, N,S co-doping, and large specific area of the pollen derived porous carbon matrix, the Co-Fe-S@NSRPC composite exhibits an excellent bifunctional catalytic activity with a small potential gap (ΔE = 0.80 V) between the half-wave potential for the ORR (0.80 V) and the potential at 10 mA cm-2 for the OER (1.60 V), and endows a liquid Zn-air battery with a high power density of 138 mW cm-2, a larger specific capacity of 891 mA h g-1 and a stable rechargeability of up to 331 cycles. Based on the Co-Fe-S@NSRPC cathode catalyst, a 2D coplanar FS-ZAB has been fabricated with specially designed parallel narrow strip electrodes alternately arrayed on a polyacrylamide polyacrylic acid copolymer hydrogel solid electrolyte. The presented FS-ZAB exhibits excellent battery performance with high open-circuit-voltage (1.415 V), competitive peak power density (78 mW cm-2), large specific capacity (785 mA h g-1) and stable rechargeability (150 cycles), offers robust flexibility to maintain stable charge/discharge capacity under different bending deformations, and provides convenient coplanar integrability to realize parallel or series connection of multiple cells in a relatively small area.

Plasma-Assisted Surface Modification on the Electrode Interface for Flexible Fiber-Shaped Zn-Polyaniline Batteries

A novel flexible fiber-shaped zinc-polyaniline battery (FZPB) is proposed to enhance the electrochemical performance, mass loading, and stability of polyaniline cathodes. To this end, electron-cyclotron-resonance oxygen plasma-modified carbon fibers are employed. During plasma treatment, on the carbon-fiber surface, O₂⁺ plasma breaks the C-C, C-H, and C-N bonds to form C radicals, while the O₂ molecules are broken down to reactive oxygen species (O⁺, O²⁺, O₂⁺, and O₂²⁺). The C radicals and the reactive oxygen species are combined to homogeneously form oxygen functional groups, such as -OH, -COOH, and -C═O. The surface area and total pore volume of the treated carbon fibers increase as the plasma attacks. During electrodeposition, aniline interacts with the oxygen functional groups to form N-O and N-H bonds and π-π stacking, resulting in a homogeneous and high-loading polyaniline structure and improved adhesion between polyaniline and carbon fibers. In an FZPB, the cathode with plasma-treated carbon fibers and a polyaniline loading of 0.158 mg mg_CF^-1 (i.e., 2.36 mg cm_CF^-1) exhibits a capacity retention of 95.39% after 200 cycles at 100 mA g^-1 and a discharge capacity of 83.96 mA h g^-1 at such a high current density of 2000 mA g^-1, which are ∼1.67 and 1.24 times those of the pristine carbon-fiber-based one, respectively. Furthermore, the FZPB exhibits high flexibility with a capacity retention of 86.4% after bending to a radius of 2.5 mm for 100 cycles as a wearable energy device.