Extremely elastic and conductive N-doped graphene sponge for monitoring human motions

Highly compressible lamellar graphene/cellulose/sodium alginate aerogel via bidirectional freeze-drying for flexible pressure sensor

Graphene exhibits exceptional electrical properties, and aerogels made from it demonstrate high sensitivity when used in sensors. However, traditional graphene aerogels have poor biocompatibility and sustainability, posing potential environmental and health risks. Moreover, the stacking of their internal structures results in low compressive strength and fatigue resistance, which limits their further applications. In this study, green and sustainable cellulose nanofibers/sodium alginate/reduced graphene oxide aerogels (BCSRA) were synthesized, featuring a well-defined lamellar structure and a fiber cross-linked network, employing techniques such as bidirectional freeze-drying, ionic cross-linking, and thermal annealing. The unique internal architecture of BCSRA results in a compressive strength of up to 64.55 kPa at 70 % compression deformation and an extremely low density of merely 7.21 mg/cm3. Furthermore, BCSRA displays outstanding fatigue resistance, maintaining 82.17 % of its stress after 100 compression cycles at 70 % compressive strain and 86.99 % after 1000 cycles at 50 % compressive strain. Remarkably, when utilized as a flexible pressure sensor, BCSRA achieves a sensitivity of 5.71 kPa-1 and endures over 2200 cycles at 40 % compression, all while ensuring consistent electrical signal output. These properties underscore its significant potential for application in wearable flexible pressure sensors, capable of detecting various human movements.

Highly Compressible Elastic Aerogel Spring-Based Piezoionic Self-Powering Pressure Sensor for Multifunctional Wearable Electronics

To meet the rapid development of wearable flexible electronics, the multifunctional integrations into singe device are in extreme demand. In this paper, we developed novel self-powering multifunctional pressure sensors and supercapacitor-integrated device based on highly elastic silver nanowires@reduced graphene aerogel, being conductive to reduce integration difficulties and device size. Serving as an energy device, it behaves with a prominent specific capacitance of 146.6 F g−1, and excellent rate capability even at 500 mV s−1. The fabricated sensor demonstrates an excellent sensitivity of 2.54 kPa−1 and superior pressure-sensing stability up to 1000 compressive cycles. Piezoionization effect is suggested to reveal the sensing mechanism. Our research provides a new research direction in designing the integration of self-driving wearable electronics.

N-doped graphene foam obtained by microwave-assisted exfoliation of graphite

The synthesis of metal-free but electrochemically active electrode materials, which could be an important contributor to environmental protection, is the key motivation for this research approach. The progress of graphene material science in recent decades has contributed to the further development of nanotechnology and material engineering. Due to the unique properties of graphene materials, they have found many practical applications: among others, as catalysts in metal-air batteries, supercapacitors, or fuel cells. In order to create an economical and efficient material for energy production and storage applications, researchers focused on the introduction of additional heteroatoms to the graphene structure. As solutions for functionalizing pristine graphene structures are very difficult to implement, this article presents a facile method of preparing nitrogen-doped graphene foam in a microwave reactor. The influence of solvent type and microwave reactor holding time was investigated. To characterize the elemental content and structural properties of the obtained N-doped graphene materials, methods such as elemental analysis, high-resolution transmission electron microscopy, scanning electron microscopy, and Raman spectroscopy were used. Electrochemical activity in ORR of the obtained materials was tested using cyclic voltamperometry (CV) and linear sweep voltamperometry (LSV). The tests proved the materials’ high activity towards ORR, with the number of electrons reaching 3.46 for tested non-Pt materials, while the analogous value for the C-Pt (20 wt% loading) reference was 4.

Fluid-Assisted Sorted Assembly of Graphene on Polymer

The significant size distribution of as-synthesized nanomaterials presents a challenge for reproducable and reliable applications. In this paper, we report a fluidic-assisted sorted assembly method in which nanomaterial sorting and enhanced assembly can be achieved simultaneously. As a proof of concept, a two-dimensional (2D) graphene flake, with a large size variation, was chosen as the target nanomaterial system. This study synergizes a novel fluidic assembly design, suspending a rotating disk over a polydimethylsiloxane (PDMS) substrate, and a computational fluid dynamics (CFD) model using Ansys CFX to disclose the mechanism of sorted assembly. By controlling the rotating speed and the gap between the disk and the substrate, the flow field is altered. In contrast to centrifugal sorting, where larger particles move outward, in this study, the size of assembled graphene flake (average lateral size, X_c) reduces significantly from the center (X_c = 3 μm) to the edge of the disk (X_c = 2 μm). The particle sorting process is dictated by the fluid shear-stress, with higher shear-stress leading to smaller particles, while the assembly process is mainly dominated by the pressure field with higher pressure magnitude leading to better assembly. Near the edge of the disk, enhanced particle sorting is coupled with an enhanced assembly where a continuous graphene film with smaller X_c can be formed. To prove the potential application of this method, an ultrasensitive strain sensor with one of the lowest detection limits, 0.02%, is demonstrated. This research presents a novel route toward large-scale and cost-effective manufacturing of nanomaterial-based flexible electronics.

Extending the pressure sensing range of porous polypyrrole with multiscale microstructures

Polymer-based piezoresistive sensors that combine the flexibility and stretchability of organic polymers have received considerable attention in flexible and wearable sensing systems. Generally, highly sensitive pressure sensors have a limited pressure sensing range, while pressure sensors with a wide pressure response range usually have limited pressure resolution. Herein, we used a polypyrrole (PPy) sponge with multiscale porous structures to extend the pressure sensing range of PPy-based piezoresistive sensors. The multiscale microstructures with different sizes will sink in sequence after increasing the external pressure and therefore exhibit a wide pressure response range. Our results show that the piezoresistive composite has a superior sensitivity of 28 kPa-1 and a broad stress range of 0-60 kPa. Moreover, the composite displays a stable, repeatable and durable performance over 16 000 cycles. It can be used to monitor diverse body part motions, including vocalization, pulse beating and joint bending. This work provides an effective strategy to extend the pressure sensing range of polymer-based piezoresistive sensors in the manner of structure design rather than modifying the intrinsic properties of active materials.

An implantable and versatile piezoresistive sensor for the monitoring of human-machine interface interactions and the dynamical process of nerve repair

Flexible wearable and implantable piezoresistive sensors have attracted lots of attention in the applications of healthcare monitoring, disease diagnostics, and human-machine interactions. However, the restricted sensing range, low sensing sensitivity at small strains, limited mechanical stability at high strains, and sophisticated fabrication processes restrict the far-reaching applications of these sensors for ultrasensitive full-range healthcare monitoring. In this work, an implantable and versatile piezoresistive sensor was developed from a series of conductive composites. The conductive composites, hydroxyethyl cellulose (HEC)/soy protein isolate (SPI)/polyaniline (PANI) sponges (HSPSs), were prepared by lyophilization of HEC/SPI solution and then in situ polymerization of aniline. The sensitivity, response time, and mechanical robustness of the HSPS sensors were characterized, and they can achieve a gauge factor of -0.29, a response time of 0.14 s, and sensing stability for at least 100 cycles. The HSPS sensors could efficiently work in vivo for 4 weeks for the measurement of stimuli, without severe inflammatory reaction. When the versatile HSPS sensors were attached to different parts of the human body, they could detect a variety of human motions including coughing, bending of fingers and elbow, abdominal breathing and walking. Notably, the HSPS sensors could be used to monitor the nerve repair in rats and the results are highly consistent with the electrophysiological data. At the same time a new score system was developed to evaluate rat nerve repair. These results indicate that the HSPS sensors exhibit good biocompatibility, sensitivity, sensing stability and fast response time. The HSPS sensors can be used not only as implantable sensors in vivo but also for analyzing human body motions. Furthermore, they provide an effective sensor device and a real-time, dynamic method for evaluating nerve repair without damage and death of animals. Hence, HSPSs might have great potential in in vivo detection, monitoring of human-machine interfacing interactions and the nerve tissue engineering field.