Large-scale production of chiral nematic microspheres

The membrane emulsification technique enables the self-assembly of cellulose nanocrystals (CNCs) confined within a spherical geometry for large-scale production. The resulting solid microspheres show long-range ordering with chiral nematic structures, and this fascinating hierarchical architecture can even be transferred to mesoporous carbon or silica microparticles by a sacrificial template method.

Relaxing Wrinkles in Jammed Interfacial Assemblies

Dynamic covalent bonding has emerged as a mean by which stresses in a network can be relaxed. Here, the strength of the bonding of ligands to nanoparticles at the interface between two immiscible liquids affect the same results in jammed assemblies of nanoparticle surfactants. Beyond a critical degree of overcrowding induced by the compression of jammed interfacial assemblies, the bonding of ligands to nanoparticles (NPs) can be broken, resulting in a desorption of the NPs from the interface. This reduces the areal density of nanoparticle surfactants at the interface, allowing the assemblies to relax, not to a fluid state but rather another jammed state. The relaxation of the wrinkles caused by the compression reflects the tendency of these assemblies to eliminate areas of high curvature, favoring a more planar geometry. This enabled the generation of giant vesicular and multivesicular structures from these assemblies.

Synthesis, characterization and adsorption behavior of modified cellulose nanocrystals towards different cationic dyes

Green and efficient removal of polluted materials are essential for the sustainability of a clean and green environment. Nanomaterials, particularly cellulose nanocrystals (CNCs), are abundant in nature and can be extracted from various sources, including cotton, rice, wheat, and plants. CNCs are renewable biomass materials with a high concentration of polar functional groups. This study used succinic anhydride to modify the surface of native cellulose nanocrystals (NCNCs). Succinic anhydride has been frequently used in adhesives and sealant chemicals for a long time, and here, it is evaluated for dye removal performance. The morphology and modification of CNCs studied using FTIR, TGA & DTG, XRD, SEM, AFM, and TEM. The ability of modified cellulose nanocrystals (MCNCs) to adsorb cationic golden yellow dye and methylene blue dye was investigated. The MCNCs exhibited high adsorption affinity for the two different cationic dyes. The maximum adsorption efficiency of NCNCs and MCNCs towards the cationic dye was 0.009 and 0.156 wt%. The investigation for adhesive properties is based on the strength and toughness of MCNCs. MCNCs demonstrated improved tensile strength (2350 MPa) and modulus (13.9 MPa) using E-51 epoxy system and a curing agent compared to 3 wt% composites. This research lays the groundwork for environmentally friendly fabrication and consumption in the industrial sector.

Role of silica-based porous cellulose nanocrystals in improving water absorption and mechanical properties

Epoxy resins are important thermosetting polymers. They are widely used in many applications i.e., adhesives, plastics, coatings and sealers. Epoxy molding compounds have attained dominance among common materials due to their excellent mechanical properties. The sol-gel simple method was applied to distinguish the impact on the colloidal time. The properties were obtained with silica-based fillers to enable their mechanical and thermal improvement. The work which we have done here on epoxy-based nanocomposites was successfully modified. The purpose of this research was to look into the effects of cellulose nanocrystals (CNCs) on various properties and applications. CNCs have recently attracted a lot of interest in a variety of industries due to their high aspect ratio, and low density which makes them perfect candidates. Adding different amounts of silica-based nanocomposites to the epoxy system. Analyzed with different techniques such as Fourier-transformed infrared spectroscope (FTIR), thermogravimetric analysis (TGA) and scanning electronic microscopic (SEM) to investigate the morphological properties of modified composites. The various %-age of silica composite was prepared in the epoxy system. The 20% of silica was shown greater enhancement and improvement. They show a better result than D-400 epoxy. Increasing the silica, the transparency of the films decreased, because clustering appears. This shows that the broad use of CNCs in environmental engineering applications is possible, particularly for surface modification, which was evaluated for qualities such as absorption and chemical resistant behavior.

Nanolatex architectonics: Influence of cationic charge density and size on their adsorption onto surfaces with a 2D or 3D distribution of anionic groups

HYPOTHESIS

It is theoretically predicted and hypothesized that the charge density and size of spherical nanoparticles are the key factors for their adsorption onto oppositely charged surfaces. It is also hypothesized that the morphology and charge of the surface are of great importance. In-plane 2D (silica) or a volumetric 3D (regenerated TEMPO-oxidized cellulose model surfaces) distribution of charged groups is expected to influence charge compensation and, thus, the adsorption behavior.

EXPERIMENTS

In this work, self-stabilized nanolatexes with a range of cationic charge densities and sizes were synthesized through reversible addition - fragmentation chain-transfer (RAFT) polymerization coupled with polymerization-induced self-assembly (PISA). Their adsorption onto silica and anionic cellulose model surfaces was investigated using stagnation point adsorption reflectometry (SPAR) and quartz crystal microbalance with dissipation (QCM-D).

FINDINGS

Experiments and theory agree and show that the size of the nanolatex and the difference in charge density compared to the substrate determine the charge compensation and, thus, the surface coverage. Highly charged or large nanolatexes overcompensate the surface charge of non-porous substrates leading to a significant repulsive zone where other particles cannot adsorb. For porous substrates like cellulose, the vertical distribution of charged groups in the 3D volume prevents overcompensation and thus increases the adsorption. This systematic study investigates the isolated effect of surface charge and size and paves the way for on-demand particles specifically designed for a surface with particular characteristics.

Incorporation of Polymer-Grafted Cellulose Nanocrystals into Latex-Based Pressure-Sensitive Adhesives

While the improvement of water-based adhesives with renewable additives is important as industry shifts toward more sustainable practices, a complete understanding of how the compatibility between additives and polymers affects adhesive performance is currently lacking. To elucidate these links, cellulose nanocrystals (CNCs) were first functionalized via surface-initiated atom-transfer radical polymerization with the hydrophobic polymers poly(butyl acrylate) (PBA) and poly(methyl methacrylate) (PMMA) to facilitate their incorporation into latex-based pressure-sensitive adhesives (PSAs). Next, PBA latexes were synthesized using seeded semibatch emulsion polymerization with unmodified or polymer-grafted CNCs added in situ at a loading of 0.5 or 1 phm (parts per hundred parts of monomer). Viscosity and electron microscopy suggested that the polymer-grafted CNCs were incorporated inside or on the latex particles. PSAs containing any CNC type had one or more improved properties (compared to the no-CNC "base case"); CNCs with a low degree of polymerization (DP) grafts exhibited improved tack (up to 2.5-fold higher) and peel strength (up to 6-fold higher) relative to PSAs with unmodified CNCs. The best performing PSA contained the low DP PMMA-grafted CNCs, which is attributed to the higher glass transition temperature and the higher wettability of the PMMA grafts compared to PBA, and the more uniform dispersion of polymer-grafted CNCs throughout the PSA film. In contrast, PSAs containing CNCs with high DP grafts resulted in reduced tack and peel strength (compared to low DP grafts) due to enhanced CNC aggregation. Unfortunately, all PSAs containing polymer-grafted CNCs exhibited inferior shear strength relative to PSAs with unmodified CNCs (and comparable shear strength to the no-CNC "base case"). Collectively, these results provide guidelines for future optimization of more sustainable latex-based PSAs.

Cellulose or chitin nanofibril-stabilized latex for medical adhesion via tailoring colloidal interactions

The objective of this research is to develop a functional medical adhesive from natural nanofibril-stabilized latex through an aqueous process. Surface charged cellulose or chitin nanofibrils are used to form Pickering emulsions of acrylic monomers, followed by in situ polymerization. Charged initiators are selected to tailor the interactions between them and nanofibrils, and it is found that the repulsive electrostatic interactions play a key role in stabilizing the heterogeneous system. As a result, poly(2-ethylhexyl acrylate-co-methyl methacrylate) latexes are successfully prepared for surfactant-free adhesives with a high shear strength of 72.0 ± 6.5 kPa. In addition, drug can be easily incorporated in the nanopaper substrate or adhesive layer to form a medical tape, exhibiting long-term drug release and antibacterial behaviors. We managed developing a facile method to integrate green synthesis, versatile functionalities and excellent adhesion into one adhesive, which remains a great challenge.

Nanocellulose in Heterogeneous Water-Based Polymerization for Wood Adhesives

The interest in the development of biobased adhesives has increased due to environmental concerns. Moreover, as the production of engineered wood products (EWPs) is expected to grow, the wood adhesives market needs to transit toward formaldehyde-free products. Cellulose nanoparticles (CNPs) are a material with unique properties and advantages for producing hybrid materials as biobased wood adhesives. Besides their traditional use as reinforcing additives, CNPs can be incorporated at the beginning of the polymerization reaction to form in situ polymerized hybrid adhesives with better mechanical and physicochemical properties than the neat adhesive. Despite their outstanding characteristics, CNPs are still an emerging nanomaterial in the wood adhesive field, and the studies are incipient. This review explores the utilization of CNPs in heterogeneous polymerization for the production of polyvinyl acetate, polymeric isocyanates, waterborne polyurethane systems, and other waterborne polymer latexes. The main challenges are discussed, and some recommendations are set down for the manufacture of these novel hybrid nanocomposites.

Swelling-based preparation of polypropylene nanocomposite with non-functionalized cellulose nanofibrils

Dispersion of nanofillers in a polymer matrix is one of the most important steps in preparing polymer nanocomposites. However, hydrophobic polymers and hydrophilic nanofillers are intrinsically incompatible, making it difficult to mix them homogeneously. Here, we propose the swelling-based particle adsorption method (SPA) providing a simple route to disperse cellulose nanofibrils (CNFs) within incompatible polypropylene (PP) matrix without surface functionalization of CNFs. The SPA enables CNFs to adsorb onto the surface of PP particles using a small amount of solvent. PP/CNFs composite films fabricated from the SPA showed increased Young's modulus by 80%, which agrees well with a theoretical prediction proving nano-dispersed. Furthermore, simply mixing a bit of polypropylene-graft-maleic anhydride can improve the tensile strength by 30% and the elongation at break by 10-fold than that of PP/CNFs composites. The SPA can be universally applied to any incompatible polymer-nanofiller pairs for the fabrication of nanocomposite materials.

Polysaccharide-Based Nanoparticles as Pickering Emulsifiers in Emulsion Formulations and Heterogenous Polymerization Systems

Bio-based Pickering emulsifiers are a nontoxic alternative to surfactants in emulsion formulations and heterogenous polymerizations. Recent demand for biocompatible and sustainable formulations has accelerated academic interest in polysaccharide-based nanoparticles as Pickering emulsifiers. Despite the environmental advantages, the inherent hydrophilicity of polysaccharides and their nanoparticles limits efficiency and application range. Modification of the polysaccharide surface is often required in the development of ultrastable, functional, and water-in-oil (W/O) systems. Complex surface modification calls into question the sustainability of polysaccharide-based nanoparticles and is identified as a significant barrier to commercialization. This review summarizes the use of nanocelluloses, -starches, and -chitins as Pickering emulsifiers, highlights trends and best practices in surface modification, and provides recommendations to expedite commercialization.

Dextran-Coated Latex Nanoparticles via Photo-RAFT Mediated Polymerization Induced Self-Assembly

Polysaccharide coated nanoparticles represent a promising class of environmentally friendly latex to replace those stabilized by small toxic molecular surfactants. We report here an in situ formulation of free-surfactant core/shell nanoparticles latex consisting of dextran-based diblock amphiphilic copolymers. The synthesis of copolymers and the immediate latex formulation were performed directly in water using a photo-initiated reversible addition fragmentation chain transfer-mediated polymerization induced self-assembly strategy. A hydrophilic macromolecular chain transfer-bearing photosensitive thiocarbonylthio group (eDexCTA) was first prepared by a modification of the reducing chain end of dextran in two steps: (i) reductive amination by ethylenediamine in the presence of sodium cyanoborohydride, (ii) then introduction of CTA by amidation reaction. Latex nanoparticles were then formulated in situ by chain-extending eDexCTA using 2-hydroxypropyl methacrylate (HPMA) under 365 nm irradiation, leading to amphiphilic dextran-b-poly(2-hydroxypropyl methacrylate) diblock copolymers (DHX). Solid concentration (SC) and the average degree of polymerization - Xn-- of PHPMA block (X) were varied to investigate their impact on the size and the morphology of latex nanoparticles termed here SCDHX. Light scattering and transmission electron microscopy analysis revealed that SCDHX form exclusively spherical nano-objects. However, the size of nano-objects, ranging from 20 nm to 240 nm, increases according to PHPMA block length.

Silica-Supported Styrene-Co-Divinylbenzene Pickering Emulsion Polymerization: Tuning Surface Charge and Hydrophobicity by pH and Co-Aid Adsorption

In this work, polymerizations of styrene (St) in the presence of divinylbenzene (DVB) as a crosslinking agent and sodium 4-vinylbenzenesulfonate (VBS) have been performed in Pickering emulsions, using silica nanoparticles (SNps) as stabilizing agents and ammonium persulfate as a hydrophilic initiator. In oil-in-water Pickering emulsions with alkaline continuous phase (pH = 9) at 1, 2, and 3 wt% DVB (relative to St), polydisperse spheroid copolymer submicronic nanoparticles were obtained. Comparatively, polymerizations performed in Pickering emulsions with acidic continuous phase (pH = 5) allowed preparing St-co-DVB microspheres with core–shell structures at 1 wt% DVB and St-co-DVB hybrid monoliths with bi-continuous morphologies at 2 and 3 wt% DVB. It is noteworthy that this work reports Pickering emulsion polymerization as a new strategy for preparing hybrid percolated scaffolds with bi-continuous porosity. The proposed mechanisms originated by pH, DVB, and VBS and the drastic impact caused on the final morphology obtained, either hybrid particles or monoliths, are discussed herein.

Creaming Layers of Nanocellulose Stabilized Water-Based Polystyrene: High-Solids Emulsions for 3D Printing

Oil-in-water emulsions stabilized using cellulose nanofibrils (CNF) form extremely stable and high-volume creaming layers which do not coalesce over extended periods of time. The stability is a result of the synergistic action of Pickering stabilization and the formation of a CNF percolation network in the continuous phase. The use of methyl cellulose (MC) as a co-emulsifier together with CNF further increases the viscosity of the system and is known to affect the droplet size distribution of the formed emulsion. Here, we utilize these highly stable creaming layer systems for in situ polymerization of styrene with the aim to prepare an emulsion-based dope for additive manufacturing. We show that the approach exploiting the creaming layer enables the effortless water removal yielding a paste-like material consisting of polystyrene beads decorated with CNF and MC. Further, we report comprehensive characterization that reveals the properties and the performance of the creaming layer. Solid-state NMR measurements confirmed the successful polymerization taking place inside the nanocellulosic network, and size exclusion chromatography revealed average molecular weight (Mw) of polystyrene as approximately 700,000 Da. Moreover, the amount of the leftover monomer was found to be less than 1% as detected by gas chromatography. The dry solids content of the paste was ∼20% which is a significant increase compared to the solids content of the original CNF dispersion (1.7 wt%). The shrinkage of the CNF, MC and polystyrene structures upon drying—an often-faced challenge—was found to be acceptable for this composite containing highly hygroscopic biobased materials. At best, the two dimensional shrinkage was no more than ca. 20% which is significantly lower than the shrinkage of pure CNF being as high as 50%. The paste, which is a composite of biobased materials and a synthetic polymer, was demonstrated in direct-ink-writing to print small objects. With further optimization of the formulation, we find the emulsion templating approach as a promising route to prepare composite materials.

Green Hydrophilic Capsules from Cellulose Nanocrystal-Stabilized Pickering Emulsion Polymerization: Morphology Control and Spongelike Behavior

Pickering inverse emulsions of hydroxyl oligoethylene glycol methacrylate were stabilized in isopropyl myristate, a biofriendly oil, using surface-modified cellulose nanocrystals (CNCs) as stabilizing particles. The emulsions were further polymerized by free or controlled radical polymerization (ATRP), taking advantage of the bromoisobutyrate functions grafted on the CNC surface. Suspension polymerization of the emulsion led to full bead or empty capsule morphologies, depending on the initiation locus. The thickness of the CNC shell surrounding the polymerized emulsions could be tuned by modulating the aggregation state of the CNCs after their surface modification. An increase from 6 to 40 CNC layers helped improve the compression moduli of the beads from a dozen to hundreds of kPa.

Nanocellulose in Emulsions and Heterogeneous Water-Based Polymer Systems: A Review

Nanocelluloses (i.e., bacterial nanocellulose, cellulose nanocrystals, and cellulose nanofibrils) are cellulose-based materials with at least one dimension in the nanoscale. These materials have unique and useful properties and have been shown to assemble at oil-water interfaces and impart new functionality to emulsion and latex systems. Herein, the use of nanocellulose in both emulsions and heterogeneous water-based polymers is reviewed, including dispersion, suspension, and emulsion polymerization. Comprehensive tables describe past work employing nanocellulose as stabilizers or additives and the properties that can be tailored through the use of nanocellulose are highlighted. Even at low loadings, nanocellulose offers an unprecedented level of control as a property modifier for a range of emulsion and polymer applications, influencing, for example, emulsion type, stability, and stimuli-responsive behavior. Nanocellulose can tune polymer particle properties such as size, surface charge, and morphology, or be used to produce capsules and polymer nanocomposites with enhanced mechanical, thermal, and adhesive properties. The role of nanocellulose is discussed, and a perspective for future direction is presented.

Synergistic impact of cellulose nanocrystals with multiple resins on thermal and mechanical behavior

The cellulose nanocrystals (CNCs) surface modified with phenolic and acrylic resins were investigated for different properties such as thermally stability and adhesive property, the mechanical properties of CNCs and interactions of the resulting materials at a micro-level are very important. Phenolic resins are of great interest due to their smooth structure, low thermal conductivity and good thermal insulation. However, the high spray rates and poor mechanical properties limit its use for external insulation of buildings. Acrylic resins are used as a matrix resin for adhesives and composites due to their adhesion, mechanical properties, and their good chemical resistance. The brittleness of acrylic resins makes them less attractive than the structural materials, being much harder. For this reason, most of the resins are modified with suitable elastomers, which act as hardeners. Therefore, treatment of these compounds is necessary. In this research paper, the effect of CNCs surface on phenolic and acrylic resins were investigated to obtain an optimized surface using three different weight (wt%) ratios of CNCs. Scanning electronic microscopy (SEM), X-rays diffraction (XRD), Thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR) were used to characterize the structure, and investigate different properties of CNCs. Furthermore, the Zwick/Roell Z020 model was used to investigate the adhesion properties of the phenolic and acrylic resins with CNCs.

Engineered Multilayer Microcapsules Based on Polysaccharides Nanomaterials

The preparation of microcapsules composed by natural materials have received great attention, as they represent promising systems for the fabrication of micro-containers for controlled loading and release of active compounds, and for other applications. Using polysaccharides as the main materials is receiving increasing interest, as they constitute the main components of the plant cell wall, which represent an ideal platform to mimic for creating biocompatible systems with specific responsive properties. Several researchers have recently described methods for the preparation of microcapsules with various sizes and properties using cell wall polysaccharide nanomaterials. Researchers have focused mostly in using cellulose nanomaterials as structural components in a bio-mimetic approach, as cellulose constitutes the main structural component of the plant cell wall. In this review, we describe the microcapsules systems presented in the literature, focusing on the works where polysaccharide nanomaterials were used as the main structural components. We present the methods and the principles behind the preparation of these systems, and the interactions involved in stabilizing the structures. We show the specific and stimuli-responsive properties of the reported microcapsules, and we describe how these characteristics can be exploited for specific applications.

Bottom-up assembly of nanocellulose structures

Nanocelluloses, both cellulose nanofibrils and cellulose nanocrystals, are gaining research traction due to their viability as key components in commercial applications and industrial processes. Significant efforts have been made to understand both the potential of assembling nanocelluloses, and the limits and prospectives of the resulting structures. This Review focuses on bottom-up techniques used to prepare nanocellulose-only structures, and details the intermolecular and surface forces driving their assembly. Additionally, the interactions that contribute to their structural integrity are discussed along with alternate pathways and suggestions for improved properties. Six categories of nanocellulose structures are presented: (1) powders, beads, and droplets; (2) capsules; (3) continuous fibres; (4) films; (5) hydrogels; and (6) aerogels and dried foams. Although research on nanocellulose assembly often focuses on fundamental science, this Review also provides insight on the potential utilization of such structures in a wide array of applications.

Nanocellulose: From Fundamentals to Advanced Applications

Over the past few years, nanocellulose (NC), cellulose in the form of nanostructures, has been proved to be one of the most prominent green materials of modern times. NC materials have gained growing interests owing to their attractive and excellent characteristics such as abundance, high aspect ratio, better mechanical properties, renewability, and biocompatibility. The abundant hydroxyl functional groups allow a wide range of functionalizations via chemical reactions, leading to developing various materials with tunable features. In this review, recent advances in the preparation, modification, and emerging application of nanocellulose, especially cellulose nanocrystals (CNCs), are described and discussed based on the analysis of the latest investigations (particularly for the reports of the past 3 years). We start with a concise background of cellulose, its structural organization as well as the nomenclature of cellulose nanomaterials for beginners in this field. Then, different experimental procedures for the production of nanocelluloses, their properties, and functionalization approaches were elaborated. Furthermore, a number of recent and emerging uses of nanocellulose in nanocomposites, Pickering emulsifiers, wood adhesives, wastewater treatment, as well as in new evolving biomedical applications are presented. Finally, the challenges and opportunities of NC-based emerging materials are discussed.

Encapsulation of Ionic Liquids for Tailored Applications

This spotlight article highlights the favorable impact encapsulation of ionic liquids (ILs) has on multiple advanced applications. ILs are molten salts with many attractive properties such as negligible vapor pressure, good thermal stability, and high ionic conductivity; however, their widespread implementation in advanced applications is hampered by their relatively high viscosity, which makes them difficult to handle and results in slow mass transfer rates. The ability to encapsulate IL in a shell holds potential to impact many applications, including separations, gas sequestration, and energy storage and management, given that the capsule structure provides high surface area compared to that of bulk IL and also allows handling of the IL as a solid. Herein, we discuss encapsulation of ILs using different approaches and highlight the contributions from our lab in both capsule preparation and application. Specifically, we have developed the ability to use 2D carbon nanoparticle surfactants and interfacial polymerization to prepare capsules of IL using both IL-in-water and IL-in-oil Pickering emulsions as templates. This facile, one-step method to encapsulate ILs gives structures with beneficial performance in supercapacitors, separations, and CO₂ sequestration, as discussed herein. We conclude this spotlight with an outlook on how to improve upon these systems for next-generation applications.

Microsuspension Polymerization of Styrene Using Cellulose Nanocrystals as Pickering Emulsifiers: On the Evolution of Latex Particles

We report a mechanistic study of the microsuspension polymerization of styrene stabilized by cellulose nanocrystals (CNCs) in its native form as well as graft-modified with copolymers of styrene and N-3-(dimethylamino)propyl methacrylamide (DMAPMAm) or N,N-(diethylamino)ethyl methacrylate (DEAEMA). Native CNCs and graft-modified CNCs were shown to form stable styrene emulsions with an average droplet diameter of 18-20 and 5-9 μm, respectively. Initiators of widely varying water solubilities [2,2'-azobisisobutyronitrile (AIBN), 2-2'-azobis(2,4-dimethylvaleronitrile) (Vazo-52), and lauroyl peroxide (LPO)] were employed for the polymerizations. The type of initiator and the type of CNC were shown to directly affect the microsuspension polymerization kinetics, particle size, and molecular weight distribution. Using AIBN and Vazo-52, submicron latex particles were observed in the final latex in addition to the desired 3-20 μm CNC-armored microsuspension particles. The resulting latex and microsuspension polystyrene particles were studied for their CNC coverage and surface charge. We found that the presence of CNCs in the aqueous phase did not lead to Pickering emulsion polymerization by heterogeneous nucleation.