Study on adsorption of methylene blue by a novel composite material of TiO2 and alum sludge

Synthesis of graphite/rGO-modified fungal hyphae for chromium (VI) bioremediation process

Bioremediation is a promising technology that can eliminate the drawbacks of conventional treatment methods in removing harmful toxic metals including chromium(VI). Therefore, in this study, fungal hyphae modified with graphite and reduced graphene oxide were synthesized and assessed for their potential to bioremediate heavy metals for the first time in the literature. The effects of the carbon-based materials on microbial structure were characterized using scanning electron microscopy analysis. Thermogravimetric, RAMAN, X-ray diffraction, and enzymatic analyzes were performed to determine the role of functional groups. In addition, batch adsorption experiments utilizing response surface methodology were conducted to optimize operating parameters such as time (1-11 h), chromium (10-50 mg/L), and graphite/reduced graphene oxide (0.1-1 g/L). The maximum adsorption capacity with the graphene fungal hyphae was determined to be 568 mg.g-1, which is 9.7 times that of the crude fungal hyphae. The Cr(VI) removal for fungal hyphae-graphite and fungal hyphae-reduced graphene oxide biocomposites was 98.25% and 98.49%, respectively. The isothermal and kinetic results perfectly matched the 2nd order pseudo-model and Langmuir model in terms of the nature of the adsorption process. The laboratory scale test results indicate that fungal hyphae modified with graphite and reduced graphene oxide have a high adsorption capacity, suitable for the removal of chromium (VI) from wastewater.

Magnetic hydrochar grafted-chitosan for enhanced efficient adsorption of malachite green dye from aqueous solutions: Modeling, adsorption behavior, and mechanism analysis

Water pollution by organic dyes is one of the most serious environmental problems worldwide. Malachite green (MG) is considered as one the serious organic dyes which is discharged in wastewater by leather and textile manufacturing plants. MG dye can cause severe hazards to the environment and human health. Therefore, the removal of MG dye from wastewater is very important and essential. This study aims to synthesize a new magnetic hydrochar grafted to chitosan (MWSHC@CS) for the removal of MG dye from the aqueous solutions. Transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area, and Zeta potential analysis were used to characterize the synthesized MWSHC@CS. Batch experiments were conducted to optimize MG dye adsorption conditions, including adsorbent mass, pH, temperature, initial concentration, and contact time. The results revealed that MWSHC@CS had an excellent removal efficiency (96.47 %) for MG dye at the optimum condition (at m: 20 mg, pH: 7.5, t: 420 min, and T: 298 K). Adsorption isotherms outcomes revealed the MG adsorption data were best fit by the Langmuir model with a maximum adsorption capacity (420.02 mg/g). Adsorption kinetics outcomes exhibited that the adsorption process of MG dye fitted well to the Elovich model. The thermodynamic results revealed that the adsorption process was physical, exothermic, and spontaneous. The adsorption mechanisms of MG onto MWSHC@CS were hydrogen bonding, electrostatic interaction, and π-π interactions. Furthermore, MWSHC@CS showed excellent reusability for the removal of MG over five cycles of adsorption-desorption (83.76 %). In conclusion, the study provides a new, low-cost, and effective magnetic nanocomposite based on chitosan as a promising adsorbent for the high-performance removal of MG dye from aqueous solutions.

Application of modified water treatment residuals in water and wastewater treatment: A review

Large quantities of sludge known as water treatment residuals (WTRs) are generated from water treatment facilities across the world. Various attempts have been made to reuse these residuals. Among the different applications of WTRs, their reuse in water and wastewater treatment has received more attention. However, direct application of raw WTRs is associated with some limitations. In the last decade, in order to improve their characteristics, numerous investigators have modified WTRs by different methods. This paper reviews the different methods applied to WTRs to enhance their characteristics. The effects of these modifications on their characteristics are explained. The applications of modified WTRs as a filtration/adsorption medium for treating textile/dye wastewater, groundwater containing different anionic and cationic pollutants, storm water runoff, and as a substrate in constructed wetlands are presented in detail. Future research needs are highlighted. The review clearly indicates the potential of different modification methods to improve the removal of a variety of pollutants by WTRs from water and wastewater.

Extractability of Rice Husk Waste Using Green Gamma Radiation for Dye Elimination in Laboratory-Scale Sorption System: Equilibrium Isotherm and Kinetic Analysis

Nowadays, the use of natural materials and especially "waste" valorization has evolved and attracted the wide attention of scientists and academia. In this regard, the use of rice husk (RH) powder as a naturally abundant and cheap byproduct material is gaining superior attention. However, improving the physicochemical properties of such RH is still under research. In the current investigation, the modification of rice husk (RH) via γ-irradiation has shown to be a promising green tool to meet such a need. Clean, prepared, powdered RH samples were subjected to various γ-radiation doses, namely 5, 10, 15 and 25 kGy, and the corresponding samples were named as RH-0, RH-5, RH-10, RH-15, RH-15 and RH-25. Then, the samples were characterized via scanning electron microscopy (SEM). After irradiation, the samples showed an increase in their surface roughness upon increasing the γ-radiation up to 15 kGy. Furthermore, the sorption capacity of the irradiated RH samples was investigated for eliminating Urolene Blue (UB) dye as a model pharmaceutical effluent stream. The highest dye uptake was recorded as 14.7 mg/g, which corresponded to the RH-15. The adsorption operating parameters were also investigated for all of the studied systems and all adsorbents showed the same trend, of a superior adsorption capacity at pH 6.6 and high temperatures. Langmuir and Freundlich isotherm models were also applied for UB adsorption and an adequate fitted isotherm model was linked with Langmuir fitting. Moreover, the pseudo-second-order kinetic model provided the best fit for the adsorption data. Experimental assays confirmed that the UB dye could be successfully eradicated feasibly from the aqueous stream via a sustainable green methodology.

Chitin-Based Magnesium Oxide Biocomposite for the Removal of Methyl Orange from Water

In this work, a cost-effective chitin-based magnesium oxide (CHt@MgO) biocomposite with excellent anionic methyl orange (MO) dye removal efficiency from water was developed. The CHt@MgO biocomposite was characterized by FT-IR, XRD, SEM-EDX, and TGA/DTG. Results proved the successful synthesis of CHt@MgO biocomposite. Adsorption of MO on the CHt@MgO biocomposite was optimized by varying experimental conditions such as pH, amount of adsorbent (m), contact time (t), temperature (T), and initial MO concentration (C_o). The optimized parameters for MO removal by CHt@MgO biocomposite were as follows: pH, 6; m, 2 g/L; t, 120 min. Two common isotherm models (Langmuir and Freundlich) and three kinetic models (pseudo-first-order (PFO), pseudo-second-order (PSO), and intraparticle diffusion (IPD)) were tested for experimental data fitting. Results showed that Langmuir and PFO were the most suitable to respectively describe equilibrium and kinetic results on the adsorption of MO adsorption on CHt@MgO biocomposite. The maximum Langmuir monolayer adsorption capacity (q_m) on CHt@MgO biocomposite toward MO dye was 252 mg/g at 60 °C. The reusability tests revealed that CHt@MgO biocomposite possessed high (90.7%) removal efficiency after the fifth regeneration cycle.

Adsorptive Pattern Using Drinking Water Treatment Residual for Organic Effluent Abatement from Aqueous Solutions

Zeolite (ZSM-12) is a unique material obtained from the drinking water treatment plants' residual "alum sludge", as a result of using aluminum sulphate as a primary coagulant in the plants. Herein, alum sludge (AS) is initially dewatered and subjected for various calcination temperatures 400 °C, 600 °C and 800 °C and the corresponding materials are named as AS400, AS600 and AS800, respectively. Such calcination is provided to attain ZSM-12, which is considered a highly adsorptive material. The material characterization and morphology were investigated using scanning X-ray diffraction (XRD) and electron microscope (SEM) that confirm the presence of ZSM-12 and porosity of such prepared materials. Thereafter, such materials are introduced for phenol remediation from aqueous solution. The experimental data reveal that AS400 had the largest adsorption capacity (275 mg-_phenol/g), in comparison to the commercial adsorbent materials during 2 h of isotherm time. Such a result confirms the suitability of alum sludge residue to be a good candidate for environmental remediation. Furthermore, adsorption isotherm models were applied, and the data are well-fitted to the Langmuir isotherm model. In addition, thermodynamic parameters are investigated which verify the physisorption adsorption process and exothermic nature with a spontaneous reaction system.

Efficient adsorption of heavy metals from wastewater on nanocomposite beads prepared by chitosan and paper sludge

Chitosan was commonly used with inorganic salt and organic compounds to prepare adsorption material for water treatment. Different materials were mixed for the preparation, leading to a high cost for water treatment. Sludge from papermaking has abundant fiber and inorganic salt, which can reduce the addition of raw materials in preparing the adsorption material and thus lower the cost. This work used recycled industrial paper sludge to prepare adsorption material to remove heavy metals from wastewater. The adsorption properties of the prepared sludge-chitosan material for Cu²⁺ and Cr³⁺ in wastewater were investigated. The impacts of adsorption time, pH, and initial concentrations of Cu²⁺ and Cr³⁺ on adsorption amount were studied and optimized. The saturated adsorption capacity of sludge-chitosan material for Cu²⁺ and Cr³⁺ can reach 114.6 and 110.3 mg/g. The adsorption kinetics satisfied the pseudo-second-order model, indicating two modes, physical diffusion, and chem-sorption, in the heavy metal adsorption by the sludge-chitosan materials. Physical distribution has little Effect on chemical adsorption. The materials can be applied to treating Cu²⁺ and Cr³⁺ containing wastewater with the proposed cheap and readily available sludge-chitosan material. The results confirmed that sludge-chitosan material possessed good regeneration performance and was an ideal adsorbent.

Investigation on the feasibility of recycled polyvinylidene difluoride polymer from used membranes for removal of methylene blue: experimental and DFT studies

This study reports the feasibility of recycled polyvinylidene difluoride (PVDF) beads to decolourize methylene blue (MB) from aqueous streams. The beads were characterized using scanning electron microscopy (SEM), X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FT-IR) for its morphological and structural analysis. The effect of various process parameters such as adsorbent dose, initial concentration, contact time, and pH was studied. The first principle density functional theory (DFT) calculations were performed to investigate the underlying mechanism behind the adsorption process. The MB dye adsorption on recycled PVDF beads followed the pseudo-second-order kinetics and Langmuir isotherm, indicating the adsorption was chemical and monolayer. The maximum adsorption capacity obtained was 27.86 mg g^-1. The adsorption energy of MB-PVDF predicted from the DFT study was -64.7 kJ mol^-1. The HOMO-LUMO energy gap of PVDF decreased from 9.42 eV to 0.50 eV upon interaction with MB dye due to the mixing of molecular orbitals. The DFT simulations showed that the interaction of the MB dye molecule was from the electronegative N atom of the MB dye molecule, implying that electrostatic interactions occurred between the recycled PVDF beads and the positively charged quaternary ammonium groups in MB dye. The present study demonstrates the potential of recycled PVDF beads for a low-cost dye removal technique from textile wastewater.

Sulfhydryl Functionalized Magnetic Chitosan as an Efficient Adsorbent for High-Performance Removal of Cd(II) from Water: Adsorption Isotherms, Kinetic, and Reusability Studies

In this study, dimercaptosuccinic acid-functionalized magnetic chitosan (Fe3O4@CS@DMSA) was synthesized via in situ coprecipitation process and amidation reaction, aiming to eliminate cadmium (Cd(II)) ions from an aqueous environment. The structure, morphology, and particle size of the Fe3O4@CS@DMSA adsorbent were investigated using FTIR, TEM, EDX, TGA, zeta potential, and XRD techniques, and the obtained results approved the successful synthesis of the Fe3O4@CS@DMSA nanocomposite. The influence of external adsorption conditions such as pH solution, adsorbent mass, initial Cd(II) concentration, temperature, and contact time on the adsorption process was successfully achieved. Accordingly, pH: 7.6, contact time: 210 min, and adsorbent mass:10 mg were found to be the optimal conditions for best removal. The adsorption was analyzed using nonlinear isotherm and kinetic models. The outcomes revealed that the adsorption process obeyed the Langmuir and the pseudo-first-order models. The maximum adsorption capacity of Fe3O4@CS@DMSA toward Cd(II) ion was 314.12 mg/g. The adsorption mechanism of Cd(II) on Fe3O4@CS@DMSA nanocomposite is the electrostatic interaction. The reusability test of Fe3O4@CS@DMSA nanocomposite exhibited that the adsorption efficiency was 72% after the 5th cycle. Finally, this research indicates that the Fe3O4@CS@DMSA exhibited excellent characteristics such as high adsorption capacity, effective adsorption-desorption results, and easy magnetic separation and thus could be an effective adsorbent for removing Cd(II) ions from aqueous solutions.

Heterogeneous Photocatalytic Chlorination of Methylene Blue Using a Newly Synthesized TiO2-SiO2 Photocatalyst

The titanium dioxide-silicon dioxide (TiO2-SiO2) nanocomposite used for the study was synthesized using a sol-gel method followed by UV-treatment. The physicochemical properties of the synthesized catalyst, TiO2-SiO2 were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS) and photoluminescence (PL). The photocatalytic degradation of methylene blue (MB) dye was evaluated in the presence of TiO2-SiO2 and reactive chlorine species (RCS) under experimental conditions. By comparing the important reaction processes in the study, including photocatalysis, chlorination and photocatalytic chlorination, it was found out that the process of photocatalytic chlorination had the highest photodegradation efficiency (95% at 60 min) of the MB under optimum reaction conditions (MB = 6 mg L−1, catalyst = 0.1 g and pH = 4). The enhanced removal of MB from the aqueous medium was identified because of the synergy between chlorination and photocatalysis activated in the presence of TiO2-SiO2. The mechanism of the photocatalytic chlorination process was scrutinized in the presence of various RCS and reactive oxygen species (ROS) scavengers. Based on the experimental data attained, Na2S2O3 exhibited the highest inhibitory effect on the degradation efficiency of MB, indicating that the RCS is the main contributor to visible light-induced photodegradation of MB.

Guar gum based nanocomposites: Role in water purification through efficient removal of dyes and metal ions

Researchers nowadays are relentlessly on a race exploring sustainable materials and techniques for the sequestration of toxic dyes and metal ions from water bodies. Biopolymers such as guar gum, owing to its high abundance, low cost and non-toxicity, are potential candidates in this field. Plenty of hydroxyl groups in the polymer backbone enable guar gum to be functionalised or grafted in a versatile manner proving itself as an excellent starting substance for fabricating upgraded materials meant for diverse applications. This review offers a comprehensive coverage of the role of guar gum-based nanocomposites in removal of dyes and heavy metal ions from waste water through adsorption and photo-catalytic degradation. Isotherm and kinetics models, fabrication routes, characterisation techniques, swelling properties and reusability as well as adsorption and degradation mechanisms are outlined. A detailed analysis with convincing results suggests a good future perspective of implementation of these materials in real-time wastewater treatment technology.

A Molecularly Imprinted Fluorescence Sensor Based on the ZnO Quantum Dot Core-Shell Structure for High Selectivity and Photolysis Function of Methylene Blue

ZnO quantum dots and CuFe2O4 nanoparticles were synthesized by chemical precipitation. The ZCF composite was created by the solvothermal method. A new molecularly imprinted fluorescence sensor (ZCF@MB-MIP) with unique optical properties and specific MB recognition was successfully generated. ZCF@MB-MIPs were characterized by Fourier-transform infrared spectroscopy, transmission electron microscopy, and X-ray diffraction and were applied for the selective detection of methylene blue (MB). The optimal working time of ZCF@MB-MIPs was 15 min, and the optimal working concentration was 37 mg·L-1. The fluorescence intensity was linearly quenched within the 0-100 μmol·L-1 MB range, and the detection limit was 1.27 μmol·L-1. The imprinting factor of the sensor (IF, K MB-MIPs/N-MIPs) was 5.30. At the same time, a real-time monitoring system was established for the photodegradation process of MB, which had the effect of reflecting the degradation degree of MB at any given time. Hence, ZCF@MB-MIPs are a promising candidate for use in MB monitoring, and they also provides a new strategy for constructing a multifunctional fluorescence sensor with a high selectivity and photolysis function.

Synthesis, characterization and photo-catalytic activity of guar-gum-g-aliginate@silver bionanocomposite material

The green mechanism for the synthesis of nanoparticles and their application to the wastewater treatment is of inordinate curiosity to the research community. Herein we outline a novel method for the synthesis of silver nanoparticles via a green route using alginate-guar gum blend (GG-Alg@Ag) and their application to degrade methylene blue (MB) dye. The synthesized material was characterized by FTIR, XRD, SEM-EDX, TEM, TGA-DTG, AFM, and UV-vis techniques. A combination of RSM and CCD was employed to compute the system and optimized values of various interacting parameters such as exposure time (120 min), pH (4.98), dye concentration (194 mg L⁻¹), and catalyst dose (0.07 g) with a photodegradation capacity of 92.33% and desirability 1.0. The mechanism of degradation reaction was best elucidated by the pseudo-second-order model suggesting chemical deposition of MB on the GG-Alg@Ag surface through followed by the reduction mechanism in the occupancy of visible light. The optical studies indicated a value of 2.5 eV by Tauc's plot for bandgap energy (E_g) for GG-Alg@Ag bionanocomposite.

The green mechanism for the synthesis of nanoparticles and their application to the wastewater treatment is of inordinate curiosity to the research community.