Research Progress of Non-Noble Metal Catalysts for Carbon Dioxide Methanation

The extensive utilization of fossil fuels has led to a rapid increase in atmospheric CO2 concentration, resulting in various environmental issues. To reduce reliance on fossil fuels and mitigate CO2 emissions, it is important to explore alternative methods of utilizing CO2 and H2 as raw materials to obtain high-value-added chemicals or fuels. One such method is CO2 methanation, which converts CO2 and H2 into methane (CH4), a valuable fuel and raw material for other chemicals. However, CO2 methanation faces challenges in terms of kinetics and thermodynamics. The reaction rate, CO2 conversion, and CH4 yield need to be improved to make the process more efficient. To overcome these challenges, the development of suitable catalysts is essential. Non-noble metal catalysts have gained significant attention due to their high catalytic activity and relatively low cost. In this paper, the thermodynamics and kinetics of the CO2 methanation reaction are discussed. The focus is primarily on reviewing Ni-based, Co-based, and other commonly used catalysts such as Fe-based. The effects of catalyst supports, preparation methods, and promoters on the catalytic performance of the methanation reaction are highlighted. Additionally, the paper summarizes the impact of reaction conditions such as temperature, pressure, space velocity, and H2/CO2 ratio on the catalyst performance. The mechanism of CO2 methanation is also summarized to provide a comprehensive understanding of the process. The objective of this paper is to deepen the understanding of non-noble metal catalysts in CO2 methanation reactions and provide insights for improving catalyst performance. By addressing the limitations of CO2 methanation and exploring the factors influencing catalyst effectiveness, researchers can develop more efficient and cost-effective catalysts for this reaction.

Modified fischer-tropsch synthesis: A review of highly selective catalysts for yielding olefins and higher hydrocarbons

Global warming, fossil fuel depletion, climate change, as well as a sudden increase in fuel price have motivated scientists to search for methods of storage and reduction of greenhouse gases, especially CO2. Therefore, the conversion of CO2 by hydrogenation into higher hydrocarbons through the modified Fischer–Tropsch Synthesis (FTS) has become an important topic of current research and will be discussed in this review. In this process, CO2 is converted into carbon monoxide by the reverse water-gas-shift reaction, which subsequently follows the regular FTS pathway for hydrocarbon formation. Generally, the nature of the catalyst is the main factor significantly influencing product selectivity and activity. Thus, a detailed discussion will focus on recent developments in Fe-based, Co-based, and bimetallic catalysts in this review. Moreover, the effects of adding promoters such as K, Na, or Mn on the performance of catalysts concerning the selectivity of olefins and higher hydrocarbons are assessed.

Cerium d-Block Element (Co, Ni) Bimetallic Oxides as Catalysts for the Methanation of CO2: Effect of Pressure

Nickel– and cobalt–cerium bimetallic oxides were used as catalysts for the methanation of CO2 under pressure. The catalysts’ activity increases with pressure and an increase of just 10 bar is enough to double the yield of methane and to significantly improve the selectivity. The best results were those obtained over nickel–cerium bimetallic oxides, but the effect of pressure was particularly relevant over cobalt–cerium bimetallic oxides, which yield to methane increases from almost zero at atmospheric pressure to 50–60% at 30 bar. Both catalyst types are remarkably competitive, especially those containing nickel, which were always more active than a commercial rhodium catalyst used as a reference (5wt.% Rh/Al2O3) and tested under the same conditions. For the cobalt–cerium bimetallic oxides, the existence of a synergetic interaction between Co and CoO and the formation of cobalt carbides seems to play an important role in their catalytic behavior. Correlation between experimental reaction rates and simulated data confirms that the catalysts’ behavior follows the Langmuir–Hinshelwood–Hougen–Watson kinetic model, but Le Chatelier’s principle is also important to understand the catalysts’ behavior under pressure. A catalyst recycle study was also performed. The results obtained after five cycles using a nickel–cerium catalyst show insignificant variations in activity and selectivity, which are important for any type of practical application.

Structural and Valence State Modification of Cobalt in CoPt Nanocatalysts in Redox Conditions

Platinum is the primary catalyst for many chemical reactions in the field of heterogeneous catalysis. However, platinum is both expensive and rare. Therefore, it is advantageous to combine Pt with another metal to reduce cost while also enhancing stability. To that end, Pt is often combined with Co to form Co-Pt nanocrystals. However, dynamical restructuring effects that occur during reaction in Co-Pt ensembles can impact catalytic properties. In this study, model Co₂Pt₃ nanoparticles supported on carbon were characterized during a redox cycle with two in situ approaches, namely, X-ray absorption spectroscopy (XAS) and scanning transmission electron microscopy (STEM) using a multimodal microreactor. The sample was exposed to temperatures up to 500 °C under H₂, and then to O₂ at 300 °C. Irreversible segregation of Co in the Co₂Pt₃ particles was seen during redox cycling, and substantial changes of the oxidation state of Co were observed. After H₂ treatment, a fraction of Co could not be fully reduced and incorporated into a mixed Co-Pt phase. Reoxidation of the sample increased Co segregation, and the segregated material had a different valence state than in the fresh, oxidized sample. This in situ study describes dynamical restructuring effects in CoPt nanocatalysts at the atomic scale that are crucial to understand in order to improve the design of catalysts used in major chemical processes.

Catalysts for the Conversion of CO2 to Low Molecular Weight Olefins-A Review

There is a large worldwide demand for light olefins (C₂⁼-C₄⁼), which are needed for the production of high value-added chemicals and plastics. Light olefins can be produced by petroleum processing, direct/indirect conversion of synthesis gas (CO + H₂) and hydrogenation of CO₂. Among these methods, catalytic hydrogenation of CO₂ is the most recently studied because it could contribute to alleviating CO₂ emissions into the atmosphere. However, due to thermodynamic reasons, the design of catalysts for the selective production of light olefins from CO₂ presents different challenges. In this regard, the recent progress in the synthesis of nanomaterials with well-controlled morphologies and active phase dispersion has opened new perspectives for the production of light olefins. In this review, recent advances in catalyst design are presented, with emphasis on catalysts operating through the modified Fischer-Tropsch pathway. The advantages and disadvantages of olefin production from CO₂ via CO or methanol-mediated reaction routes were analyzed, as well as the prospects for the design of a single catalyst for direct olefin production. Conclusions were drawn on the prospect of a new catalyst design for the production of light olefins from CO₂.

The Influence of Preparation Method on the Physicochemical Characteristics and Catalytic Activity of Co/TiO2 Catalysts

Two Co/TiO2 catalysts with 7% CoO/g loading were prepared using equilibrium deposition filtration and the dry impregnation method. The two catalysts were characterized with various physicochemical techniques and tested for the degradation of sulfamethaxazole (SMX) using sodium persulfate (SPS) as the oxidant. It was found that the two catalysts exhibit different physicochemical characteristics. The equilibrium deposition filtration (EDF) catalyst had a higher dispersion of cobalt phase, more easily reduced Co(III) species, and a higher ratio of Co(III)/Co(II) species. The interactions between Co-deposited species and the titania surface were monitored with diffuse reflectance spectroscopy in all the preparation steps, and it was found that they increased during drying and calcination, while EDF favored the formation of surface species with strong interactions with the support. Finally, the EDF catalyst was more active for the degradation of sulfamethaxazole due to its better physicochemical characteristics.