Development of electrochemical sensors for quick detection of environmental (soil and water) NPK ions

All over the world, technology is becoming more and more prevalent in agriculture. Different types of instruments are already being used in this sector. For the time being, every farmer is trying to produce more crops on a piece of land. Eventually, soil loses its nutrients; however, to grow more crops, farmers use more fertilizers without knowing the proper conditions of the soil in real time. To overcome this issue, many scientists have recently focused on developing electrochemical sensors to detect macronutrients, i.e., nitrogen (N), phosphorus (P), and potassium (K), in soil or water rapidly. In this review, we focus mainly on the recent developments in electrochemical sensors used for the detection of nutrients (NPK) in different types of samples. As it is outlined, the use of smart and portable electrochemical sensors can be helpful for the reduction of excess fertilizer and can play a vital role in maintaining suitable conditions in soils and water. We are optimistic that this review can guide researchers in the development of a portable and suitable NPK detection system for soil nutrients.

Recent advances in aptamer-based biosensors for potassium detection

Maintaining a stable level of potassium is crucial for proper bodily function because even a slight imbalance can result in serious disorders like hyperkalemia and hypokalemia. Therefore, detecting and monitoring potassium ion (K+) levels are of utmost importance. Various biosensors have been developed for rapid K+ detection, with aptamer-based biosensors garnering significant attention due to their high sensitivity and specificity. This review focuses on aptamer-based biosensors for K+ detection, providing an overview of their signal generation strategies, including electrochemical, field-effect transistor, nanopore, colorimetric, and fluorescent systems. The analytical performance of these biosensors is evaluated comprehensively. In addition, factors that affect their efficiency, such as their physicochemical properties, regeneration for reusability, and linkers/spacers, are listed. Lastly, this review examines the major challenges faced by aptamer-based biosensors in K+ detection and discusses potential future developments.

A theoretical and experimental study of polyaniline/GCE and DNA G-quadruplex conformation as an impedimetric biosensor for the determination of potassium ions

An electrochemical aptasensor has been developed to determine K⁺ using electrochemical impedance spectroscopy. The polyaniline (PANI) coating was first electrodeposited on a GCE. Then, the potassium-selective aptamer [G₃(T₂AG₃)₃] was adsorbed through an electrostatic force between PANI and aptamer. In the presence of K⁺, the single-stranded DNA is folded into the G-quadruplex configuration, which acts as a barrier against electron transfer at the GCE surface. AFM and FE-SEM images characterize the surface morphology at each fabrication stage. As the K⁺ concentration increased, the charge transfer resistance (R_ct) increased, and the plot of ΔR_ct versus the logarithm of the K⁺ concentration is linear over a wide range of 10 pM-60 μM with a low detection limit of 3.7 pM. Finally, the proposed sensor was used to determine K⁺ in water, serum, urine, and fruit samples. Moreover, the binding stability of the aptamer/PANI and K⁺/Aptamer/PANI and the interactions between the aptamer and PANI were analyzed through molecular dynamics simulation.

The dynamicity of light-up aptamers in one-pot in vitro diagnostic assays

Light-up aptamers are aptamers that ignite the fluorescence emission of certain dyes upon binding. Widely harnessed in in vivo imaging, the binding capacity of the light-up aptamers can also be deployed in in vitro diagnostic assays, engendering a mix-and-read format. Intrigued by this, I intend to provide an overview of the various formats of diagnostic assays developed using light-up aptamers from the direct modulation of the light-up aptamers, split aptamer-based configuration, strand displacement, in vitro transcription-based one-pot diagnostic assay, CRISPR-Cas system to the measurement of the ion reliance. The incorporation of the light-up aptamers into each configuration is expounded and further supported by describing the exemplary assays developed thus far. It is anticipated that the present study can be enlightening to any researchers who aspire to embark on the development of one-pot in vitro diagnostic assays based on light-up aptamers.

Electrochemical Detection of Electrolytes Using a Solid-State Ion-Selective Electrode of Single-Piece Type Membrane

This study aimed to develop simple electrochemical electrodes for the fast detection of chloride, sodium and potassium ions in human serum. A flat thin-film gold electrode was used as the detection electrode for chloride ions; a single-piece type membrane based solid-state ion-selective electrode (ISE), which was formed by covering a flat thin-film gold electrode with a mixture of 7,7,8,8-tetracyanoquinodimethane (TCNQ) and ion-selective membrane (ISM), was developed for sodium and potassium ions detection. Through cyclic voltammetry (CV) and square-wave voltammetry (SWV), the detection data can be obtained within two minutes. The linear detection ranges in the standard samples of chloride, sodium, and potassium ions were 25-200 mM, 50-200 mM, and 2-10 mM, with the average relative standard deviation (RSD) of 0.79%, 1.65%, and 0.47% and the average recovery rates of 101%, 100% and 96%, respectively. Interference experiments with Na+, K+, Cl-, Ca2+, and Mg2+ ions demonstrated that the proposed detection electrodes have good selectivity. Moreover, the proposed detection electrodes have characteristics such as the ability to be prepared under relatively simple process conditions, excellent detection sensitivity, and low RSD, and the detection linear range is suitable for the Cl-, Na+ and K+ concentrations in human serum.

From Small Molecules Toward Whole Cells Detection: Application of Electrochemical Aptasensors in Modern Medical Diagnostics

This paper focuses on the current state of art as well as on future trends in electrochemical aptasensors application in medical diagnostics. The origin of aptamers is presented along with the description of the process known as SELEX. This is followed by the description of the broad spectrum of aptamer-based sensors for the electrochemical detection of various diagnostically relevant analytes, including metal cations, abused drugs, neurotransmitters, cancer, cardiac and coagulation biomarkers, circulating tumor cells, and viruses. We described also possible future perspectives of aptasensors development. This concerns (i) the approaches to lowering the detection limit and improvement of the electrochemical aptasensors selectivity by application of the hybrid aptamer-antibody receptor layers and/or nanomaterials; and (ii) electrochemical aptasensors integration with more advanced microfluidic devices as user-friendly medical instruments for medical diagnostic of the future.

Advances in Electrochemical Aptasensors Based on Carbon Nanomaterials

Carbon nanomaterials offer unique opportunities for the assembling of electrochemical aptasensors due to their high electroconductivity, redox activity, compatibility with biochemical receptors and broad possibilities of functionalization and combination with other auxiliary reagents. In this review, the progress in the development of electrochemical aptasensors based on carbon nanomaterials in 2016–2020 is considered with particular emphasis on the role of carbon materials in aptamer immobilization and signal generation. The synthesis and properties of carbon nanotubes, graphene materials, carbon nitride, carbon black particles and fullerene are described and their implementation in the electrochemical biosensors are summarized. Examples of electrochemical aptasensors are classified in accordance with the content of the surface layer and signal measurement mode. In conclusion, the drawbacks and future prospects of carbon nanomaterials’ application in electrochemical aptasensors are briefly discussed.