Optimum selective separation of Cu(ii) using 3D ordered macroporous chitosan films with different pore sizes

Advanced technologies in water treatment: Chitosan and its modifications as effective agents in the adsorption of contaminants

Chitosan, derived from the abundant biopolymer chitin, has emerged as a promising option for water treatment due to its intrinsic bioavailability. This review emphasizes the notable characteristics of chitosan, which allow for various modifications, expanding its applications. The polymer's effectiveness in adsorbing contaminants, particularly in advanced water treatment technologies, is highlighted. The review underscores the potential of chitosan-based hybrid materials, including nanocomposites, hydrogels, membranes, films, sponges, nanoparticles, microspheres, and flakes, as innovative alternatives to traditional chemical-based adsorbents. The advantages of using these materials in wastewater treatment, especially in removing heavy metals, dyes, and emerging compounds, are explored. The study delves into the mechanisms involved in wastewater treatment with chitosan, emphasizing the interactions between the polymer and various contaminants. Additionally, the application of chitosan as a contaminant removal agent in a post-pandemic context is addressed, considering the challenges related to waste management and environmental preservation. The analysis highlights the potential contribution of chitosan in mitigating environmental impacts post-pandemic, offering practical solutions for treating contaminated effluents and promoting sustainability. The study addresses current obstacles and prospects for chitosan-based wastewater treatment, emphasizing its promising role in sustainable water management.

Crown Ether Grafted Graphene Oxide/Chitosan/Polyvinyl Alcohol Nanofiber Membrane for Highly Selective Adsorption and Separation of Lithium Ion

Nanofiber membranes were successfully prepared with crown ether (CE) functionalized graphene oxide (GO), chitosan (CS), and polyvinyl alcohol (PVA) by low-temperature thermally induced liquid-liquid phase separation. The physical and chemical properties and adsorption performance of nanofiber membrane were studied through SEM, FT-IR, XRD, and static adsorption experiments. The results show that the specific surface area of the nanofiber membrane is as high as 101.5 m2∙g-1. The results of static adsorption experiments show that the maximum adsorption capacity of the nanofiber membrane can reach 168.50 mg∙g-1 when the pH is 7.0. In the selective adsorption experiment, the nanofiber membrane showed high selectivity for Li+ in salt lake brine. After five cycles, the material still retains 88.31% of the adsorption capacity. Therefore, it is proved that the material has good regeneration ability.

Honeycomb-like porous chitosan films prepared via phase transition of poly(N-isopropylacrylamide) during water evaporation under ambient conditions

Honeycomb-like porous chitosan (CS) films are attractive tools for developing functional materials for filters, catalyses, adsorbents, biomaterials, etc. A simple method for fabricating honeycomb-like porous CS films without special reagents, facilities, and techniques would make them accessible. Here we introduce an easily available method for fabricating honeycomb-like CS films without a strong acid/base, toxic reagents, or special facilities/techniques. An aqueous solution containing CS and poly(N-isopropylacrylamide) (PNIPAm) was allowed to stand at 25 °C to evaporate water. After 3 days, CS–PNIPAm composite films with homogenously phase-separated PNIPAm particles were obtained. The PNIPAm particles were removed by immersion in methanol, and the resulting films dried under reduced pressure to become honeycomb-like porous CS films. The pore size could be varied in the range of 0.5–3.0 μm by altering the CS concentration and the molecular weight of CS where the pore size was reduced under conditions with stronger interaction between CS molecules. We reveal that the key to success with this system is the decrease of lower critical solution temperature (LCST) of PNIPAm with water evaporation. In addition, we confirmed the removed PNIPAm was recyclable in this system. Furthermore, we found this method was also applicable to alginate. The proposed facile method for fabricating honeycomb-like porous polymeric films could provide various functional porous materials.

A simple method for fabricating honeycomb-like porous chitosan films without special reagents, facilities, and techniques was achieved by using poly(N-isopropylacrylamide).