Efficient conversion of ethanol to 1-butanol and C5–C9 alcohols over calcium carbide

Eco-friendly solvent-based liquid-liquid extraction of phenolic acids from winery wastewater streams

This study proposes liquid-liquid extraction (LLE) for the recovery of phenolic acids from winery wastewater replacing common volatile organic compounds (VOCs) with environmentally friendly solvents. On one hand, terpenes (α-pinene and p-cymene) and terpenoids (eucalyptol and linalool) were selected as green solvents and compared to common VOCs (ethyl acetate or 1-butanol). On the other hand, gallic acid (GA), vanillic acid (VA), syringic acid (SA) and caffeic acid (CA) were selected as phenolic acids to be recovered. The extraction performance was evaluated under different operation conditions: solvent-to-feed ratio, initial concentration of phenolic acids and temperature. This work also evaluated the back-extraction whole process global recovery and solvent regeneration, by means of aqueous NaOH solution. Eucalyptol has shown the highest overall global extraction performance (21.07 % for GA, 93.21 % for VA, 78.79 % for SA, and 80.57 % for CA) and lower water solubility compared to the best performing VOC solvent (1-butanol). Therefore, eucalyptol can be a potential eco-friendly solvent to replace VOCs for sustainable phenolic acid recovery from winery wastewater. Finally, to ensure a clean water stream after the LLE, the traces of solvent were completely removed by electrooxidation with boron-doped diamond anode at a current density of 422.54 A/m2.

Potentials of bio-butanol conversion to valuable products

In the last decade, there was observed a growing demand for both n-butanol as a potential fuel or fuel additive, and propylene as the only raw material for production of alcohol and other more bulky propylene chemical derivatives with faster growing outputs (polymers, propylene oxide, and acrylic acid). The predictable oilfield depletion and the European Green Deal adoption stimulated interest in alternative processes for n-butanol production, especially those involving bio-based materials. Their commercialization will promote additional market penetration of n-butanol for its application as a basic chemical. We analyze briefly the current status of two most advanced bio-based processes, i.e. ethanol–to-n-butanol and acetone–butanol–ethanol (ABE) fermentation. In the second part of the review, studies of n-butanol and ABE conversion to valuable products are considered with an emphasis on the most perspective catalytic systems and variants of the future processes realization.

Structural Evolution of MOF-Derived RuCo, A General Catalyst for the Guerbet Reaction

Guerbet alcohols, a class of β-branched terminal alcohols, find widespread application because of their low melting points and excellent fluidity. Because of the limitations in the activity and selectivity of existing Guerbet catalysts, Guerbet alcohols are not currently produced via the Guerbet reaction but via hydroformylation of oil-derived alkenes followed by aldol condensation. In pursuit of a one-step synthesis of Guerbet alcohols from simple linear alcohol precursors, we show that MOF-derived RuCo alloys achieve over a million turnovers in the Guerbet reaction of 1-propanol, 1-butanol, and 1-pentanol. The active catalyst is formed in situ from ruthenium-impregnated metal-organic framework MFU-1. XPS and XAS studies indicate that the precatalyst is composed of Ru precursor trapped inside the MOF pores with no change in the oxidation state or coordination environment of Ru upon MOF incorporation. The significantly higher reactivity of Ru-impregnated MOF versus a physical mixture of Ru precursor and MOF suggests that the MOF plays an important role in templating the formation of the active catalyst and/or its stabilization. XPS reveals partial reduction of both ruthenium and MOF-derived cobalt under the Guerbet reaction conditions, and TEM/EDX imaging shows that Ru is decorated on the edges of dense nanoparticles, as well as thin nanoplates of CoOx. The use of ethanol rather than higher alcohols as a substrate results in lower turnover frequencies, and RuCo recovered from ethanol upgrading lacks nanostructures with plate-like morphology and does not exhibit Ru-enrichment on the surface and edge sites. Notably, 1H and 31P NMR studies show that through use of K3PO4 as a base promoter in the RuCo-catalyzed alcohol upgrading, the formation of carboxylate salts, a common side product in the Guerbet reaction, was effectively eliminated.

Transition metal-free and solvent-free calcium carbide promotes the formation of β-keto sulfoxide from acyl chloride and DMSO

A transition metal-free, solvent-free, cheap and readily available calcium carbide promoted one-pot reaction of acid chloride with dimethyl sulfoxide produced β-keto sulfoxide directly.

Ethanol Dehydrogenation: A Reaction Path Study by Means of Temporal Analysis of Products

Conventional fossil fuels such as gasoline or diesel should be substituted in the future by environmentally-friendly alternatives in order to reduce emissions in the transport sector and thus mitigate global warming. In this regard, iso-butanol is very promising as its chemical and physical properties are very similar to those of gasoline. Therefore, ongoing research deals with the development of catalytically-supported synthesis routes to iso-butanol, starting from renewably-generated methanol. This research has already revealed that the dehydrogenation of ethanol plays an important role in the reaction sequence from methanol to iso-butanol. To improve the fundamental understanding of the ethanol dehydrogenation step, the Temporal Analysis of Products (TAP) methodology was applied to illuminate that the catalysts used, Pt/C, Ir/C and Cu/C, are very active in ethanol adsorption. H2 and acetaldehyde are formed on the catalyst surfaces, with the latter quickly decomposing into CO and CH4 under the given reaction conditions. Based on the TAP results, this paper proposes a reaction scheme for ethanol dehydrogenation and acetaldehyde decomposition on the respective catalysts. The samples are characterized by means of N2 sorption and Scanning Transmission Electron Microscopy (STEM).