Highly sensitive polyaniline-coated fiber gas sensors for real-time monitoring of ammonia gas

AIE paper shred for the detection of evolved amine vapor from putrefaction processes of fish

Seafood plays a major role in the human diet. During transportation, without proper storage and supply chain, its quality deteriorates easily. The post-harvesting processes such as the storage of food play a crucial role in human health. So it is highly imperative to have a technique for identifying food spoilage earlier to ensure the food safety and security of the consumers. Herein we have developed a highly selective and sensitive fluorescent 'Turn-on' probe 2-amino-5-nitrobenzo [d] thiazol-2-yl) imino)methylphenol ANT based on aggregation induced emission (AIE). ANT molecule possesses both restricted intramolecular rotation (RIR) and excited state intramolecular proton transfer (ESIPT) properties leading to fluorescent enhancement rather than aggregation caused quenching (ACQ). The probe shows high selectivity and sensitivity towards the NH3 vapor. This probe with the AIE property is employed for the real-time detection of NH3 in both aqueous and gaseous phases. ANT molecule is deposited on the paper shred by a physical method is utilized to monitor NH3 vapor from red snapper fish as a real-time sample during its degradation processes. After two days there is a ratiometric color change in the paper shred from yellow to orange for the fish stored at room temperature indicating its rotten and unpalatability nature. Paper shred is reused by immersing it into the tetrahydrofuran (THF), in which it retains its initial color due to deprotonation of NH3, keto to enol tautomerism discloses the reusability of the fluorescent probe. Studies carried out using UV-visible and fluorescence spectroscopy infer that the ANT probe has high affinity towards NH3 vapor.

Nitrogen in landfills: Sources, environmental impacts and novel treatment approaches

Nitrogen (N) accumulation in landfills is a pressing environmental concern due to its diverse sources and significant environmental impacts. However, there is relatively limited attention and research focus on N in landfills as it is overshadowed by other more prominent pollutants. This study comprehensively examines the sources of N in landfills, including food waste contributing to 390 million tons of N annually, industrial discharges, and sewage treatment plant effluents. The environmental impacts of N in landfills are primarily manifested in N2O emissions and leachate with high N concentrations. To address these challenges, this study presents various mitigation and management strategies, including N2O reduction measures and novel NH4+ removal techniques, such as electrochemical technologies, membrane separation processes, algae-based process, and other advanced oxidation processes. However, a more in-depth understanding of the complexities of N cycling in landfills is required, due to the lack of long-term monitoring data and the presence of intricate interactions and feedback mechanisms. To ultimately achieve optimized N management and minimized adverse environmental impacts in landfill settings, future prospects should emphasize advancements in monitoring and modeling technologies, enhanced understanding of microbial ecology, implementation of circular economy principles, application of innovative treatment technologies, and comprehensive landfill design and planning.

Porous Conductive Textiles for Wearable Electronics

Over the years, researchers have made significant strides in the development of novel flexible/stretchable and conductive materials, enabling the creation of cutting-edge electronic devices for wearable applications. Among these, porous conductive textiles (PCTs) have emerged as an ideal material platform for wearable electronics, owing to their light weight, flexibility, permeability, and wearing comfort. This Review aims to present a comprehensive overview of the progress and state of the art of utilizing PCTs for the design and fabrication of a wide variety of wearable electronic devices and their integrated wearable systems. To begin with, we elucidate how PCTs revolutionize the form factors of wearable electronics. We then discuss the preparation strategies of PCTs, in terms of the raw materials, fabrication processes, and key properties. Afterward, we provide detailed illustrations of how PCTs are used as basic building blocks to design and fabricate a wide variety of intrinsically flexible or stretchable devices, including sensors, actuators, therapeutic devices, energy-harvesting and storage devices, and displays. We further describe the techniques and strategies for wearable electronic systems either by hybridizing conventional off-the-shelf rigid electronic components with PCTs or by integrating multiple fibrous devices made of PCTs. Subsequently, we highlight some important wearable application scenarios in healthcare, sports and training, converging technologies, and professional specialists. At the end of the Review, we discuss the challenges and perspectives on future research directions and give overall conclusions. As the demand for more personalized and interconnected devices continues to grow, PCT-based wearables hold immense potential to redefine the landscape of wearable technology and reshape the way we live, work, and play.

Highly sensitive Cu-ethylenediamine/PANI composite sensor for NH3 detection at room temperature

Ammonia detection is needed in several sectors including environmental monitoring, automobile industry, and in medical diagnosis. Conducting polymers, such as polyaniline (PANI), have been utilized to develop NH₃ sensors operating at room temperature. However, the performance of these sensors in terms of sensitivity and selectivity need improvement. Functionalization of conducting PANI with metal nanocomposites have shown improved sensor performance. In this work, we report a highly sensitive copper-based nanocomposite for NH₃ detection. The novelty lies in utilization of copper-ethylenediamine (Cu-en) nanocomposite functionalized over PANI for gas sensing. Resistance of the 20 wt% Cu-en with PANI increased 3.8 times upon exposure to 100 ppm of NH₃. The nanocomposite sensor detected NH₃ concentrations as low as 2 ppm. Further, the sensing mechanism was studied by in-situ IV characteristics and impedance spectroscopy during NH₃ exposure. NH₃ showed ionic interaction with PANI, and Cu²⁺. The strong affinity of Cu²⁺ for the lone pair of NH₃ enhanced the sensor response from 0.78 to 3.8 for 100 ppm of NH₃ at 20 °C. The sensor response was completely recovered after heating at 75 °C, which indicates reusability of the sensor. The sensor showed selectivity for NH₃ over ethanol and H₂S. The response was reasonably stable after bending the flexible sensor for 1000 times at a radius of 5 mm.

A Review of Electro Conductive Textiles Utilizing the Dip-Coating Technique: Their Functionality, Durability and Sustainability

The presented review summarizes recent studies in the field of electro conductive textiles as an essential part of lightweight and flexible textile-based electronics (so called e-textiles), with the main focus on a relatively simple and low-cost dip-coating technique that can easily be integrated into an existing textile finishing plant. Herein, numerous electro conductive compounds are discussed, including intrinsically conductive polymers, carbon-based materials, metal, and metal-based nanomaterials, as well as their combinations, with their advantages and drawbacks in contributing to the sectors of healthcare, military, security, fitness, entertainment, environmental, and fashion, for applications such as energy harvesting, energy storage, real-time health and human motion monitoring, personal thermal management, Electromagnetic Interference (EMI) shielding, wireless communication, light emitting, tracking, etc. The greatest challenge is related to the wash and wear durability of the conductive compounds and their unreduced performance during the textiles' lifetimes, which includes the action of water, high temperature, detergents, mechanical forces, repeated bending, rubbing, sweat, etc. Besides electrical conductivity, the applied compounds also influence the physical-mechanical, optical, morphological, and comfort properties of textiles, depending on the type and concentration of the compound, the number of applied layers, the process parameters, as well as additional protective coatings. Finally, the sustainability and end-of-life of e-textiles are critically discussed in terms of the circular economy and eco-design, since these aspects are mainly neglected, although e-textile' waste could become a huge problem in the future when their mass production starts.

Preparation and Characterization of PEDOT:PSS/TiO2 Micro/Nanofiber-Based Gas Sensors

In this study, we employed electrospinning technology and in situ polymerization to prepare wearable and highly sensitive PVP/PEDOT:PSS/TiO₂ micro/nanofiber gas sensors. PEDOT, PEDOT:PSS, and TiO₂ were prepared via in situ polymerization and tested for characteristic peaks using energy-dispersive X-ray spectroscopy (EDS) and Fourier transform infrared spectroscopy (FT-IR), then characterized using a scanning electron microscope (SEM), a four-point probe resistance measurement, and a gas sensor test system. The gas sensitivity was 3.46–12.06% when ethanol with a concentration between 12.5 ppm and 6250 ppm was measured; 625 ppm of ethanol was used in the gas sensitivity measurements for the PEDOT/composite conductive woven fabrics, PVP/PEDOT:PSS nanofiber membranes, and PVP/PEDOT:PSS/TiO₂ micro/nanofiber gas sensors. The latter exhibited the highest gas sensitivity, which was 5.52% and 2.35% greater than that of the PEDOT/composite conductive woven fabrics and PVP/PEDOT:PSS nanofiber membranes, respectively. In addition, the influence of relative humidity on the performance of the PVP/PEDOT:PSS/TiO₂ micro/nanofiber gas sensors was examined. The electrical sensitivity decreased with a decrease in ethanol concentration. The gas sensitivity exhibited a linear relationship with relative humidity lower than 75%; however, when the relative humidity was higher than 75%, the gas sensitivity showed a highly non-linear correlation. The test results indicated that the PVP/PEDOT:PSS/TiO₂ micro/nanofiber gas sensors were flexible and highly sensitive to gas, qualifying them for use as a wearable gas sensor platform at room temperature. The proposed gas sensors demonstrated vital functions and an innovative design for the development of a smart wearable device.

Smart Electronic Textiles for Wearable Sensing and Display

Increasing demand of using everyday clothing in wearable sensing and display has synergistically advanced the field of electronic textiles, or e-textiles. A variety of types of e-textiles have been formed into stretchy fabrics in a manner that can maintain their intrinsic properties of stretchability, breathability, and wearability to fit comfortably across different sizes and shapes of the human body. These unique features have been leveraged to ensure accuracy in capturing physical, chemical, and electrophysiological signals from the skin under ambulatory conditions, while also displaying the sensing data or other immediate information in daily life. Here, we review the emerging trends and recent advances in e-textiles in wearable sensing and display, with a focus on their materials, constructions, and implementations. We also describe perspectives on the remaining challenges of e-textiles to guide future research directions toward wider adoption in practice.

Microfluidic devices based on textile threads for analytical applications: state of the art and prospects

Microfluidic devices based on textile threads have interesting advantages when compared to systems made with traditional materials, such as polymers and inorganic substrates (especially silicon and glass). One of these significant advantages is the device fabrication process, made more cheap and simple, with little or no microfabrication apparatus. This review describes the fundamentals, applications, challenges, and prospects of microfluidic devices fabricated with textile threads. A wide range of applications is discussed, integrated with several analysis methods, such as electrochemical, colorimetric, electrophoretic, chromatographic, and fluorescence. Additionally, the integration of these devices with different substrates (e.g., 3D printed components or fabrics), other devices (e.g., smartphones), and microelectronics is described. These combinations have allowed the construction of fully portable devices and consequently the development of point-of-care and wearable analytical systems.

Wash-Durable Conductive Yarn with Ethylene Glycol-Treated PEDOT:PSS for Wearable Electric Heaters

Recently, wearable electric heaters with high durability and low-power operation have attracted much attention due to their potential to change traditional approaches for personal heating management and thermal therapy systems. Here, we report textile-based wearable heaters based on highly durable conductive yarns, which were transformed from traditional cotton yarns through a facile dyeing process of poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) and ethylene glycol (EG). With the EG post-treatment, the conductive yarns exhibited an electrical conductivity of ∼76 S cm^-1 and good stability under repeated cycles of washing and drying. The heating elements made from the conductive yarns showed an excellent distribution of temperature and could be heated up to 150 °C at a sufficiently low driving voltage of 5 V. Also, the heating elements showed stable Joule heating performance under repeated bending stress and 2000 cycles of stretching and releasing. To demonstrate its practical use for on-body heating systems, a lightweight and air-breathable thermal wristband was demonstrated by sewing the conductive yarns onto a fabric with a simple circuit structure. From these results, we believe that our strategy to obtain highly conductive and durable yarns can be utilized in various applications, including medical heat therapy and personal heating management systems.

A rapid and highly sensitive paper-based colorimetric device for the on-site screening of ammonia gas

A rapid and highly sensitive paper-based colorimetric device for the on-site detection of ammonia (NH₃) gas is presented in this study. The detection principle of this device is based upon a change of color from red to yellow on a paper that has been immobilized with a pH indicator, i.e., methyl orange (pK_a = 3.4), in the presence of NH₃ gas. The color signal of the device can be measured through the hue channel of an HSL system via the application of a smartphone. This device can detect the amount of NH₃ gas within 3 min. The linear relationship between the NH₃ gas concentration and the hue signal was found to be in the range from 6.0 to 54.0 ppbv with R² = 0.9971, and the limit of detection was found to be 2.0 ppbv. In addition, this device showed remarkably high selectivity to NH₃ gas amongst the other common volatile organic compounds and general gases that are present in environmental air without the assistance of any membrane material. Furthermore, we demonstrated the applicability of this device for the detection of total NH₃ gas at a chicken farm and in a laboratory, with relative standard deviations of 6.2% and 5.4%, respectively. The developed NH₃ gas device in the study is easy to operate and cost-effective, with the reduction of a large consumption of chemical reagents; also, its signals can be measured simply and then recorded through a smartphone. It is suitable for the application of routine on-site detection of NH₃ gas, especially concerning regions which have limited resources.

Bio-Inspired Electronic Textile Yarn-Based NO2 Sensor Using Amyloid-Graphene Composite

Graphene-based e-textile gas sensors have received significant attention as wearable electronic devices for human healthcare and environmental monitoring. Theoretically, more the attached graphene on the devices, better is the gas-sensing performance. However, it has been hampered by poor adhesion between graphene and textile platforms. Meanwhile, amyloid nanofibrils are reputed for their ability to improve adhesion between materials, including between graphene and microorganisms. Despite that fact, there has been no attempt to apply amyloid nanofibrils to fabricate graphene-based e-textiles. By biomimicking the adhesion ability of amyloid nanofibrils, herein, we developed a graphene-amyloid nanofibril hybrid e-textile yarn (RGO/amyloid nanofibril/CY) for the detection of NO₂. Compared to traditional e-textile yarn, the RGO/amyloid nanofibril/CY showed better performance in response time, sensing efficiency, sensitivity, and selectivity for NO₂. Last, we suggested a practical use of RGO/amyloid nanofibril/CY combined with a light-emitting diode as a wearable e-textile gas sensor.

Highly Conductive and Flexible Dopamine-Graphene Hybrid Electronic Textile Yarn for Sensitive and Selective NO2 Detection

Graphene-based electronic textile (e-textile) gas sensors have been developed for detecting hazardous NO₂ gas. For the e-textile gas sensor, electrical conductivity is a critical factor because it directly affects its sensitivity. To obtain a highly conductive e-textile, biomolecules have been used for gluing the graphene to the textile surface, though there remain areas to improve, such as poor conductivity and flexibility. Herein, we have developed a dopamine-graphene hybrid electronic textile yarn (DGY) where the dopamine is used as a bio-inspired adhesive to attach graphene to the surface of yarns. The DGY shows improved electrical conductivity (∼40 times) compared to conventional graphene-based e-textile yarns with no glue. Moreover, it exhibited improved sensing performance in terms of short response time (∼2 min), high sensitivity (0.02 μA/ppm), and selectivity toward NO₂. The mechanical flexibility and durability of the DGY were examined through a 1000-cycle bending test. For a practical application, the DGY was attempted to detect the NO_x emitted from vehicles, including gasoline, diesel, and fuel cell electric vehicles. Our results demonstrated that the DGYs-as a graphene-based e-textile gas sensor for detecting NO₂-are simple to fabricate, cheap, disposable, and mechanically stable.