The Impact of Ar or N2 Atmosphere on the Structure of Bi-Fe-Carbon Xerogel Based Composites as Electrode Material for Detection of Pb2+ and H2O2

In this study, bismuth- and iron-embedded carbon xerogels (XG) were obtained using a modified resorcinol formaldehyde sol-gel synthesis method followed by additional enrichment with iron content. Pyrolysis treatment was performed at elevated temperatures under Ar or N2 atmosphere to obtain nanocomposites with different reduction yields (XGAr or XGN). The interest was focused on investigating the extent to which changes in the pyrolysis atmosphere of these nanocomposites impact the structure, morphology, and electrical properties of the material and consequently affect the electroanalytical performance. The structural and morphological particularities derived from X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) measurements revealed the formation of the nanocomposite phases, mostly metal/oxide components. The achieved performances for the two modified electrodes based on XG treated under Ar or N2 atmosphere clearly differ, as evidenced by the electroanalytical parameters determined from the detection of heavy metal cations (Pb2+) or the use of the square wave voltammetry (SWV) technique, biomarkers (H2O2), or amperometry. By correlating the differences obtained from electroanalytical measurements with those derived from morphological, structural, and surface data, a few utmost important aspects were identified. Pyrolysis under Ar atmosphere favors a significant increase in the α-Fe2O3 amount and H2O2 detection performance (sensitivity of 0.9 A/M and limit of detection of 0.17 μM) in comparison with pyrolysis under N2 (sensitivity of 0.5 A/M and limit of detection of 0.36 μM), while pyrolysis under N2 atmosphere leads to an increase in the metallic Bi amount and Pb2+ detection performance (sensitivity of 8.44 × 103 A/M and limit of detection of 33.05 pM) in comparison with pyrolysis under Ar (sensitivity of 6.47·103 A/M and limit of detection of 46.37 pM).

Facile and Affordable Design of MXene-Co3 O4 -Based Nanocomposites for Detection of Hydrogen Peroxide in Cancer Cells: Toward Portable Tool for Cancer Management

Hydrogen peroxide (H2 O2 ) is a primary reactive oxygen species (ROS) that can act as a chemical signal in developing and progressing serious and life-threatening diseases like cancer. Due to the stressful nature of H2 O2 , there is an urgent need to develop sensitive analytical approaches to be applied to various biological matrices. Herein, a portable point-of-care electrochemical system based on MXene-Co3 O4 nanocomposites to detect H2 O2 in different cancer cell-lines is presented. The developed sensor is affordable, disposable, and highly selective for H2 O2 detection. This approach achieves a dynamic linear range of 75 µm with a LOD of 0.5 µm and a LOQ of 1.6 µm. To improve the practical application, the level of ROS is evaluated both in cancer cell lines MDA-MB-231 and DU145, respectively, to breast and prostate cancers, and in healthy HaCat cells. Moreover, the same cancer cells are treated with transforming growth factor-β1, and MXene-Co3 O4 modified strip is capable to monitorROS variation. The results are satisfactory compared with the cellular ROS fluorescent assay based on DCFH/DCFH-DA. These results open new perspectives for real-time monitoring of cancer progression and the efficacy of the therapy.

A non-enzymatic electrochemical hydrogen peroxide sensor based on copper oxide nanostructures

This article describes the synthesis of nanostructured copper oxide on copper wires and its application for the detection of hydrogen peroxide. Copper oxide petal nanostructures were obtained by a one-step hydrothermal oxidation method. The resulting coating is uniform and dense and shows good adhesion to the wire surface. Structure, surface, and composition of the obtained samples were studied using field-emission scanning electron microscopy along with energy-dispersive spectroscopy and X-ray diffractometry. The resulting nanostructured samples were used for electrochemical determination of the H₂O₂ content in a 0.1 M NaOH buffer solution using cyclic voltammetry, differential pulse voltammetry, and i-t measurements. A good linear relationship between the peak current and the concentration of H₂O₂ in the range from 10 to 1800 μM was obtained. The sensitivity of the obtained CuO electrode is 439.19 μA·mM^-1. The calculated limit of detection is 1.34 μM, assuming a signal-to-noise ratio of 3. The investigation of the system for sensitivity to interference showed that the most common interfering substances, that is, ascorbic acid, uric acid, dopamine, NaCl, glucose, and acetaminophen, do not affect the electrochemical response. The real milk sample test showed a high recovery rate (more than 95%). According to the obtained results, this sensor is suitable for practical use for the qualitative detection of H₂O₂ in real samples, as well as for the quantitative determination of its concentration.

Efficient Electrochemical Detection of Hydrogen Peroxide Based on Silver-Centered Preyssler-Type Polyoxometalate Hybrids

Four polyoxometalate (POM)-based organic-inorganic hybrid compounds, namely, (H₂bimb)₆H₈[((Mn(H₂O)₃(μ-bimb))_0.5(Mn(H₂O)₄)(Mn(H₂O)₅)_0.5(AgP₅W₃₀O₁₁₀))₂]·29H₂O (1), [(Cu(Hbimb)(H₂O)₂(μ-bimb)Cu(Hbimb)(H₂O))(Cu(H₂O)₂(μ-bimb)Cu(H₂O)₃)((Cu(H₂O)₂)_0.5(μ-bimb)(Cu(H₂O)₃)_0.5)H₂(AgP₅W₃₀O₁₁₀)]·12.5H₂O (2), (H₂bimb)₂H[(Zn(Hbimb)(H₂O)₄(Zn(Hbimb)(H₂O)₂)_0.5)₂(AgP₅W₃₀O₁₁₀)]·12H₂O (3), and (H₂bimb)₃H₂[(Ag(H₂O)₂)_0.5(Ag(Hbimb)Ag(Hbimb)(μ-bimb)Ag)(Ag(H₂O)₂)_0.5(AgP₅W₃₀O₁₁₀)]·7H₂O (4) (bimb = 1,4-bis(1H-imidazol-1-yl)benzene), were hydrothermally synthesized using a silver-centered Preyssler-type POM K₁₄[AgP₅W₃₀O₁₁₀]·18H₂O (abbreviated as K-{AgP₅W₃₀}) as a precursor. In 1-4, {AgP₅W₃₀} clusters integrating the merits of Ag⁺ and {P₅W₃₀} units are modified by different transition metal (TM)-organic fragments to extend the structures into three-dimensional frameworks. As nonenzymatic electrochemical sensor materials, 1-4 show good electrocatalytic activity, high sensitivity, and a low detection limit for detecting hydrogen peroxide (H₂O₂); 4 possesses the highest sensitivity of 195.47 μA·mM^-1·cm^-2 for H₂O₂ detection. Most importantly, the average level of H₂O₂ detection of these {AgP₅W₃₀}-based materials outperforms that of Na-centered Preyssler-type {NaP₅W₃₀} and most Keggin-type POM-based materials. The performances of such {AgP₅W₃₀} materials mainly stem from the unique advantage of high-negatively charged {AgP₅W₃₀} clusters together with the good synergistic effect between {AgP₅W₃₀} and TMs. This work expands on the research of high-efficiency POM-based nonenzymatic electrochemical H₂O₂ sensors using Ag-containing POMs with high negative charges, which is also of great theoretical and practical significance to carry out health monitoring and environmental analysis.

A facile construction of Ag/MoSe2 composite based non-enzymatic amperometric sensor for hydrogen peroxide

We report an electrochemical non-enzymatic method for hydrogen peroxide (H2O2) detection based on Ag nanoparticle-decorated MoSe2 (Ag/MoSe2-500) hybrid nanostructures. These hybrid nanocomposites are easily prepared by in-situ reduction of Ag+...

Determination of dopamine based on a temperature-sensitive PMEO2MA and Au@rGO-MWCNT nanocomposite-modified electrode

First, the nanocomposite Au@rGO-MWCNT was synthesized by a hydrothermal method. Next, a temperature-controlled composite sensing film was prepared by composite modification of poly(2-(2-methoxyethoxy)ethyl methacrylate) (PMEO₂MA) and Au@rGO-MWCNT on a glassy carbon electrode (GCE). This sensor was shown to exhibit good temperature sensitivity and reversibility to dopamine. When the testing temperature is lower than the lower critical solution temperature (LCST) of the polymer, the PMEO₂MA chain is in a stretched state, which increases the distance between the Au@rGO layers and leads to the inability of MWCNTs in one layer to contact another Au@rGO layer and to low conductivity. Therefore, in this state, dopamine cannot detect an electrochemical signal, and it is termed an "off" state. When the temperature is higher than the LCST of the polymer, the PMEO₂MA chain shrinks, allowing the MWCNTs to make contact with another layer of Au@rGO; the electron transfer rate of the modified film increases, and the electrochemical behavior of dopamine turns to an "on" state. Moreover, the sensor has a wide detection range (0.1 to 9.0 μM and 9.0 to 239.0 μM), and the limit of detection of dopamine is as low as 30 nM. This method has been successfully applied to the determination of dopamine in human serum samples. The on-off sensor provides a new avenue for the application of temperature-sensitive polymers.

Crumpled Graphene/Poly (azure I) Modified Electrode for Non-enzymatic Detection of Hydrogen Peroxide Secreted from Tumor Cells

Hydrogen peroxide (H₂O₂), an important representatives of reactive oxygen species, its aberrant expression is related to many diseases, including cancers. Therefore, it is very significant to design a reliable method for the real-time detection of endogenous H₂O₂. Herein, we describe preparing a poly (azure I)/crumpled graphene (cGN) modified electrode by an electro-polymerization method. The results showed that this electrode presented obvious electrocatalytic effect on the reduction of H₂O₂. Amperometric method was employed to monitor H₂O₂, and the amperometric response exhibited a good linear relationship with its concentration in the range of 8.0 × 10^-6 - 1.25 × 10^-3 mol/L; the detection limit reached to 6.7 × 10^-7 mol/L (S/N = 3). Furthermore, this modified also displayed good selectivity, long-term stability and a high anti-interference ability. Excitingly, the established method could be successfully used to detect H₂O₂ in human serum samples, and measured H₂O₂ secreted from living MCF-7 cells. It could have potential use in cancer diagnosis.

Biosensing platform on ferrite magnetic nanoparticles: Synthesis, functionalization, mechanism and applications

Ferrite magnetic nanoparticles (FMNPs) are gaining popularity to design biosensors for high-performance clinical diagnosis. The fusion of information shows that FMNPs based biosensors require well-tuned FMNPs as detection probes to produce large and specific biological signals with minimal non-specific binding. Nevertheless, there is a noticeable lacuna of information to solve the issues related to suitable synthesis route, particle size reduction, functionalization, sensitivity towards targeted intercellular biological tiny particles, and lower signal-to-noise ratio. Therefore it allows exploring unique characteristics of FMNPs to design a suitable sensing device for intracellular measurements and diseases detection. This review focuses on the extensively used synthesis routes, their advantages and limitations, crystalline structure, functionalization, along with recent applications of FMNPs in biosensors, taking into consideration their analytical figures of merit and range of linearity. This work also addresses the current progress, key factors for sensitivity, selectivity and productivity improvement along with the challenges, future trends and perspectives of FMNPs based biosensors.

Detection Technologies for Reactive Oxygen Species: Fluorescence and Electrochemical Methods and Their Applications

Reactive oxygen species (ROS) have been found in plants, mammals, and natural environmental processes. The presence of ROS in mammals has been linked to the development of severe diseases, such as diabetes, cancer, tumors, and several neurodegenerative conditions. The most common ROS involved in human health are superoxide (O2•-), hydrogen peroxide (H2O2), and hydroxyl radicals (•OH). Organic and inorganic molecules have been integrated with various methods to detect and monitor ROS for understanding the effect of their presence and concentration on diseases caused by oxidative stress. Among several techniques, fluorescence and electrochemical methods have been recently developed and employed for the detection of ROS. This literature review intends to critically discuss the development of these techniques to date, as well as their application for in vitro and in vivo ROS detection regarding free-radical-related diseases. Moreover, important insights into and further steps for using fluorescence and electrochemical methods in the detection of ROS are presented.

Hemoglobin–metal2+ phosphate nanoflowers with enhanced peroxidase-like activities and their performance in the visual detection of hydrogen peroxide

Hemoglobin (Hgb)–metal²⁺ phosphate nanoflowers (Hgb–X²⁺-Nfs) were synthesized using Co²⁺, Zn²⁺, Ca²⁺, and Fe²⁺ separately as inorganic components, to generate a visual hydrogen peroxide (H₂O₂) biosensor for the first time.

Carbon Xerogel Nanostructures with Integrated Bi and Fe Components for Hydrogen Peroxide and Heavy Metal Detection

Multifunctional Bi- and Fe-modified carbon xerogel composites (CXBiFe), with different Fe concentrations, were obtained by a resorcinol-formaldehyde sol-gel method, followed by drying in ambient conditions and pyrolysis treatment. The morphological and structural characterization performed by X-ray diffraction (XRD), Raman spectroscopy, N2 adsorption/desorption porosimetry, scanning electron microscopy (SEM) and scanning/transmission electron microscopy (STEM) analyses, indicates the formation of carbon-based nanocomposites with integrated Bi and Fe oxide nanoparticles. At higher Fe concentrations, Bi-Fe-O interactions lead to the formation of hybrid nanostructures and off-stoichiometric Bi2Fe4O9 mullite-like structures together with an excess of iron oxide nanoparticles. To examine the effect of the Fe content on the electrochemical performance of the CXBiFe composites, the obtained powders were initially dispersed in a chitosan solution and applied on the surface of glassy carbon electrodes. Then, the multifunctional character of the CXBiFe systems is assessed by involving the obtained modified electrodes for the detection of different analytes, such as biomarkers (hydrogen peroxide) and heavy metal ions (i.e., Pb2+). The achieved results indicate a drop in the detection limit for H2O2 as Fe content increases. Even though the current results suggest that the surface modifications of the Bi phase with Fe and O impurities lower Pb2+ detection efficiencies, Pb2+ sensing well below the admitted concentrations for drinkable water is also noticed.

Cu2O-mediated assembly of electrodeposition of Au nanoparticles onto 2D metal-organic framework nanosheets for real-time monitoring of hydrogen peroxide released from living cells

The development of metal nanoparticles (MNP) combined with a metal-organic framework (MOF) has received more and more attention due to its excellent synergistic catalytic ability, which can effectively broaden the scope of catalytic reactions and enhance the catalytic ability. In this work, we developed a novel ternary nanocomposite named Cu₂O-mediated Au nanoparticle (Au NP) grown on MIL-53(Fe) for real-time monitoring of hydrogen peroxide (H₂O₂) released from living cells. First, Cu₂O-MIL-53(Fe) was prepared by redox assembly technology, which provided the growth template, and active sites for AuCl^4-. Au@Cu₂O-MIL-53(Fe)/GCE biosensor was prepared by further loading nano-Au uniformly on the surface of Cu₂O by electrochemical deposition. Compared to individual components, the hybrid nanocomposite showed superior electrochemical properties as electrode materials due to the synergistic effect between AuNPs, Cu₂O, and MIL-53(Fe). Electrochemical measurement showed that the Au@Cu₂O-MIL-53(Fe)/GCE biosensor presented a satisfactory catalytic activity towards H₂O₂ with a low detection limit of 1.01 μM and sensitivity of 351.57 μA mM^-1 cm^-2 in the linear range of 10-1520 μM. Furthermore, this biosensor was successfully used for the real-time monitoring of dynamic H₂O₂ activated by PMA released from living cells. And the great results of confocal fluorescence microscopy of the co-culture cells with PMA and Au@Cu₂O-MIL-53(Fe) verified the reliability of the biosensor, suggesting its potential application to the monitoring of critical pathological processes at the cellular level.