Highly Porous Polymer Beads Coated with Nanometer-Thick Metal Oxide Films for Photocatalytic Oxidation of Bisphenol A

Highly porous metal oxide-polymer nanocomposites are attracting considerable interest due to their unique structural and functional features. A porous polymer matrix brings properties such as high porosity and permeability, while the metal oxide phase adds functionality. For the metal oxide phase to perform its function, it must be fully accessible, and this is possible only at the pore surface, but functioning surfaces require controlled engineering, which remains a challenge. Here, highly porous nanocomposite beads based on thin metal oxide nanocoatings and polymerized high internal phase emulsions (polyHIPEs) are demonstrated. By leveraging the unique properties of polyHIPEs, i.e., a three-dimensional (3D) interconnected network of macropores, and high-precision of the atomic-layer-deposition technique (ALD), we were able to homogeneously coat the entire surface of the pores in polyHIPE beads with TiO2-, ZnO-, and Al2O3-based nanocoatings. Parameters such as nanocoating thickness, growth per cycle (GPC), and metal oxide (MO) composition were systematically controlled by varying the number of deposition cycles and dosing time under specific process conditions. The combination of polyHIPE structure and ALD technique proved advantageous, as MO-nanocoatings with thicknesses between 11 ± 3 and 40 ± 9 nm for TiO2 or 31 ± 6 and 74 ± 28 nm for ZnO and Al2O3, respectively, were successfully fabricated. It has been shown that the number of ALD cycles affects both the thickness and crystallinity of the MO nanocoatings. Finally, the potential of ALD-derived TiO2-polyHIPE beads in photocatalytic oxidation of an aqueous bisphenol A (BPA) solution was demonstrated. The beads exhibited about five times higher activity than nanocomposite beads prepared by the conventional (Pickering) method. Such ALD-derived polyHIPE nanocomposites could find wide application in nanotechnology, sensor development, or catalysis.

Use of Emulsion-Templated, Highly Porous Polyelectrolytes for In Vitro Germination of Chickpea Embryos: a New Substrate for Soilless Cultivation

The application of highly porous and 3D interconnected microcellular polyelectrolyte polyHIPE (PE-PH) monoliths based on (3-acrylamidopropyl)-trimethylammonium chloride as soilless cultivation substrates for in vitro embryo culture is discussed. The embryo axes isolated from chickpea seeds are inoculated onto the surface of the monoliths and allowed to germinate. Germination study show that the newly disclosed PE-PH substrate performs much better than the conventionally used agar as the germination percentage, shoot and root length, fresh and dry weight as well as the number of leaves are enhanced. The PE-PHs exhibit a higher absorption capacity of the plant growth medium, that is, 36 g·g^–1 compared to agar, that is, 20 g·g^–1, and also survive autoclaving conditions without failing. The key advantage over standard agar substrates is that they can be reused several times and also without prior sterilization. These results suggest that PE-PHs with exceptional absorption/retention properties and robustness have great potential as soilless substrates for in vitro plant cultivation.

Voltammetric Determination of Hg2+, Zn2+, and Pb2+ Ions Using a PEDOT/NTA-Modified Electrode

A novel electrochemical sensor for determining trace levels of Hg²⁺, Pb²⁺, and Zn²⁺ ions in water using square wave voltammetry (SWV) is reported. The sensor is based on a platinum electrode (Pt) modified by poly(3,4-ethylenedioxythiophene) and N _α,N _α-bis-(carboxymethyl)-l-lysine hydrate (NTA lysine) PEDOT/NTA. The modified electrode surface (PEDOT/NTA) was prepared via the introduction of the lysine-NTA group to a PEDOT/N-hydroxyphthalimide NHP electrode. The (PEDOT/NTA) was characterized via cyclic voltammetry (CV), Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM). The effects of scan rates on the electrochemical properties of the polymer electrode were also investigated. The electrochemical results were used to estimate the coverage of the electrode polymer surface and its electrostability in background electrolyte solutions. Several analytical parameters, such as polymer film thickness, metal deposition time, and pH of the electrolyte, were examined. Linear responses to Hg²⁺, Pb²⁺, and Zn²⁺ ions in the concentration range of 5-100 μg L^-1 were obtained. The limits of detection (LODs) for the determination of Hg²⁺, Pb²⁺, and Zn²⁺ ions were 1.73, 2.33, and 1.99 μg L^-1, respectively. These promising results revealed that modified PEDOT/NTA films might well represent an important addition to existing electrochemical sensor technologies.