Real-time monitored photocatalytic activity and electrochemical performance of an rGO/Pt nanocomposite synthesized via a green approach

Innovative molecularly imprinted electrochemical sensor for the nanomolar detection of Tenofovir as an anti-HIV drug

Tenofovir (TNF) is an antiviral medicine that is utilized to treat the human immunodeficiency virus (HIV). However, its level must be controlled in the human body and environment at the risk of causing kidney and liver problems. Therefore, determining TNF concentration in real samples with more advanced, inexpensive, and accurate sensing systems is essential. In this work, a novel electrochemical nanosensor for TNF determination based on molecularly imprinted polymer (MIP) on the screen-printed electrode modified with functionalized multi-walled carbon nanotubes, graphite carbon nitride, and platinum nanoparticles (MIP-Pt@g-C₃N₄/F-MWCNT/SPE) was constructed through the electro-polymerization approach. The molecularly imprinted polymers were prepared on the electrode surface with TNF as the template molecule and 2-aminophenol (2-AP) as the functional monomer. Moreover, factors that affect sensor response were optimized. Pt@g-C₃N₄/F-MWCNT nanocomposite had an excellent synergistic effect on MIP, allowing rapid and specific identification of the test substance. The results demonstrated that the electro-polymerization of 2-AP supplies large amounts of functional groups for the binding of the template molecules, which remarkably enhances the sensitivity and specific surface area of the MIP sensor. This surface enlargement increased the analyte accessibility to imprinted molecular cavities. Under optimum conditions, the oxidation peak current had a linear relationship with TNF concentration ranging from 0.005 to 0.69 μM with a low detection limit of 0.0030 μM (S/N = 3). The results demonstrated that the designed MIP sensor possesses acceptable sensitivity, repeatability, and reproducibility toward TNF determination. Moreover, the developed sensor was applied to biological and water samples to determine TNF, and satisfactory recovery results of 95.6-104.8% were obtained (RSD less than 10.0%). We confirm that combining as-synthesized nanocomposite Pt@g-C₃N₄/F-MWCNT with MIP improves the limitations of MIP-based nanosensors. The proposed electrode is also compatible with portable potentiostats, allowing on-site measurements and showing tremendous promise as a point-of-care (POC) diagnostic platform.

One-Step Microwave-Assisted Synthesis of PtNiCo/rGO Electrocatalysts with High Electrochemical Performance for Direct Methanol Fuel Cells

Platinum (Pt) is widely used as an activator in direct methanol fuel cells (DMFCs). However, the development of Pt catalyst is hindered due to its high cost and CO poisoning. A multi-metallic catalyst is a promising catalyst for fuel cells. We develop a simple and rapid method to synthesize PtNiCo/rGO nanocomposites (NCs). The PtNiCo/rGO NCs catalyst was obtained by microwave-assisted synthesis of graphene oxide (GO) with Pt, Ni, and Co precursors in ethylene glycol (EG) solution after heating for 20 min. The Pt-Ni-Co nanoparticles showed a narrow particle size distribution and were uniformly dispersed on the reduced graphene oxide without agglomeration. Compared with PtNiCo catalyst, PtNiCo/rGO NCs have superior electrocatalytic properties, including a large electrochemical active surface area (ECSA), the high catalytic activity of methanol, excellent anti-toxic properties, and high electrochemical stability. The ECSA can be up to 87.41 m2/g at a scan rate of 50 mV/s. They also have the lowest oxidation potential of CO. These excellent electrochemical performances are attributed to the uniform dispersion of PtNiCo nanoparticles, good conductivity, stability, and large specific surface area of the rGO carrier. The synthesized PtNiCo/rGO nanoparticles have an average size of 17.03 ± 1.93 nm. We also investigated the effect of catalyst material size on electrocatalytic performance, and the results indicate that PtNiCo/rGO NC catalysts can replace anode catalyst materials in fuel cell applications in the future.

Recent progress in green and biopolymer based photocatalysts for the abatement of aquatic pollutants

Enormous research studies on the abatement of anthropogenic aquatic pollutants including organic dyes, pesticides, cosmetics, antibiotics and inorganic species by using varieties of semiconductor photocatalysts have been reported in recent decades. Besides, many of these photocatalysts suffer in real applications owing to their high production cost and low stability. In many cases, the photocatalysts themselves are being considered as secondary pollutants. To eliminate these drawbacks, the green synthesized photocatalysts and the use of biopolymers as photocatalyst supports are considered in recent years. In this context, recent developments in green synthesized metals, metal oxides, other metal compounds, and carbon based photocatalysts in water purification are critically reviewed. Furthermore, the pivotal role of biopolymers including chitin, chitosan, cellulose, natural gum, hydroxyapatite, alginate in photocatalytic removal of aquatic pollutants is comprehensively reviewed. The presence of functional groups, electron trapping ability, biocompatibility, natural occurrence, and low production cost are the major reasons for using biopolymers in photocatalysis. Finally, the summary and conclusion are presented along with existing challenges in this research area.