Structural transformation and nature of defects in titanium carbide treated in different redox atmospheres

Achieving water-floatable photocatalyst on recycled bamboo chopsticks

Disposable bamboo chopsticks (DBCs) are difficult to recycle, which inevitably cause secondary pollution. Based on energy and environmental issues, we propose a facile strategy to fabricate floatable photocatalyst (fPC) coated onto DBCs, which can be flexibly used in water purification. The photocatalyst of titania and titanium carbide on bamboo (TiO2/TiC@b) was successfully constructed from TiC-Ti powders and DBCs using a coating technique followed heat treatment in carbon powder, and the fPC exhibited excellent photocatalytic activity under visible light irradation. The analysis results indicate that rutile TiO2 forms on TiC during heat treatment, achieving a low-density material with an average value of approximately 0.5233 g/cm3. The coatings of TiO2/TiC on the bamboo are firm and uniform, with a particle size of about 20-50 nm. XPS results show that a large amount of oxygen vacancies is generated, due to the reaction atmosphere of more carbon and less oxygen, further favoring to narrowing the band gap of TiO2. Furthermore, TiO2 formed on residual TiC would induce the formation of a heterojunction, which effectively inhibits the photogenerated electron-hole recombination via the charge transfer effect. Notably, the degradation of dye Rhodamine B (Rh.B) is 62.4% within 3 h, while a previous adsorption of 36.0% for 1 h. The excellent photocatalytic performance of TiO2/TiC@b can be attributed to the enhanced reaction at the water/air interface due to the reduced light loss in water, improved visible-light response, increased accessible area and charge transfer effect. Our findings show that the proposed strategy achieves a simple, low-cost, and mass-producible method to fabricate fPC onto the used DBCs, which is expected to applied in multiple fields, especially in waste recycling and water treatment.

Improving the Adhesion of Multi-Walled Carbon Nanotubes to Titanium by Irradiating the Interface with He+ Ions: Atomic Force Microscopy and X-ray Photoelectron Spectroscopy Study

A complex study of the adhesion of multi-walled carbon nanotubes to a titanium surface, depending on the modes of irradiation with He+ ions of the "MWCNT/Ti" system, was conducted using atomic force microscopy and X-ray photoelectron spectroscopy. A quantitative assessment of the adhesion force at the interface, performed using atomic force microscopy, demonstrated its significant increase as a result of treatment of the "MWCNT/Ti" system with a beam of helium ions. The nature of the chemical bonding between multi-walled carbon nanotubes and the surface of the titanium substrate, which causes this increase in the adhesion of nanotubes to titanium as a result of ion irradiation, was investigated by X-ray photoelectron spectroscopy. It was established that this bonding is the result of the formation of chemical C-O-Ti bonds between titanium and carbon atoms with the participation of oxygen atoms of oxygen-containing functional groups, which are localized on defects in the nanotube walls formed during ion irradiation. It is significant that there are no signs of direct bonding between titanium and carbon atoms.

Electrochemical Performance of Biocompatible TiC Films Deposited through Nonreactive RF Magnetron Sputtering for Neural Interfacing

The efficacy of neural electrode stimulation and recording hinges significantly on the choice of a neural electrode interface material. Transition metal carbides (TMCs), particularly titanium carbide (TiC), have demonstrated exceptional chemical stability and high electrical conductivity. Yet, the fabrication of TiC thin films and their potential application as neural electrode interfaces remains relatively unexplored. Herein, we present a systematic examination of TiC thin films synthesized through nonreactive radio frequency (RF) magnetron sputtering. TiC films were optimized toward high areal capacitance, low impedance, and stable electrochemical cyclability. We varied the RF power and deposition pressure to pinpoint the optimal properties, focusing on the deposition rate, surface roughness, crystallinity, and elemental composition to achieve high areal capacitance and low impedance. The best-performing TiC film showed an areal capacitance of 475 μF/cm2 with a capacitance retention of 93% after 5000 cycles. In addition, the electrochemical performance of the optimum film under varying scanning rates demonstrated a stable electrochemical performance even under dynamic and fast-changing stimulation conditions. Furthermore, the in vitro cell culture for 3 weeks revealed excellent biocompatibility, promoting cell growth compared with a control substrate. This work presents a novel contribution, highlighting the potential of sputtered TiC thin films as robust neural electrode interface materials.

Gas-phase synthesis of Ti2CCl2 enables an efficient catalyst for lithium-sulfur batteries

MXenes have aroused intensive enthusiasm because of their exotic properties and promising applications. However, to date, they are usually synthesized by etching technologies. Developing synthetic technologies provides more opportunities for innovation and may extend unexplored applications. Here, we report a bottom-up gas-phase synthesis of Cl-terminated MXene (Ti2CCl2). The gas-phase synthesis endows Ti2CCl2 with unique surface chemistry, high phase purity, and excellent metallic conductivity, which can be used to accelerate polysulfide conversion kinetics and dramatically prolong the cyclability of Li-S batteries. In-depth mechanistic analysis deciphers the origin of the formation of Ti2CCl2 and offers a paradigm for tuning MXene chemical vapor deposition. In brief, the gas-phase synthesis transforms the synthesis of MXenes and unlocks the hardly achieved potentials of MXenes.

Ratiometric electrochemical detection of kojic acid based on glassy carbon modified MXene nanocomposite

The significance of developing a selective and sensitive sensor for quality control purposes is underscored by the prevalent use of kojic acid (KA) in cosmetics, pharmaceuticals, and food items. KA's utility stems from its ability to inhibit tyrosinase activity. However, the instability of KA and its potential adverse effects have created a pressing need for accurate and sensitive sensors capable of analyzing real samples. This research introduces an electrochemical ratiometric sensor designed to accurately detect KA in actual cosmetic and food samples. The ratiometric sensor offers distinct advantages such as enhanced selectivity, reproducibility, and sensitivity. It achieves this by leveraging the ratio between two output signals, thereby producing reliable and undistorted results. The sensor is constructed by modifying a Glassy Carbon Electrode (GCE) with a nanocomposite consisting of Ti3C2 MXene, Prussian blue, and gold nanoparticles. The incorporation of MXene and gold nanoparticles heightens sensitivity and reduces impedance. Meanwhile, the Prussian blue signal diminishes proportionally with increasing KA concentration, forming the basis for the ratiometric sensing mechanism. The outcomes of the study reveal a broad linear range (1-600 μM), a low detection limit (1 μM), and strong selectivity for KA. These findings suggest the sensor's potential efficacy in quality control across cosmetics, pharmaceuticals, and food products.

Enhanced Electrochemical H2O2 Production via Two-Electron Oxygen Reduction Enabled by Surface-Derived Amorphous Oxygen-Deficient TiO2-x

The electrochemical oxygen reduction reaction (ORR) is regarded as an attractive alternative to the anthraquinone process for sustainable and on-site hydrogen peroxide (H₂O₂) production. It is however hindered by low selectivity due to strong competition from the four-electron ORR and needs efficient catalysts to drive the 2e^- ORR. Here, an acid oxidation strategy is proposed as an effective strategy to boost the 2e^- ORR activity of metallic TiC via in-site generation of a surface amorphous oxygen-deficient TiO_2-x layer. The resulting a-TiO_2-x/TiC exhibits a low overpotential and high H₂O₂ selectivity (94.1% at 0.5 V vs reversible hydrogen electrode (RHE)), and it also demonstrates robust stability with a remarkable productivity of 7.19 mol g_cat.^-1 h^-1 at 0.30 V vs RHE. The electrocatalytic mechanism of a-TiO_2-x/TiC is further revealed by density functional theory calculations.