The effect of surfactants on hydrate particle agglomeration in liquid hydrocarbon continuous systems: a molecular dynamics simulation study

The Solvent Role for the Decomposition of Paracetamol in Distilled and Drinking Water by Pure and Ag-Modified TiO2 Sol-Gel Powders

In this study, pure TiO2 gels were synthesized by applying the sol-gel method, using Ti(IV) butoxide with the addition of two different solvents, namely ethylene glycol (EG) and isopropanol (isop), with only air moisture present. It was established using XRD that the gel prepared with the addition of EG was amorphous even at 400 °C, while the other gel was amorphous up to 300 °C. It was found that TiO2 (anatase) had a dominant crystalline phase during heating to 600 °C, while at 700 °C, TiO2 (rutile) appeared. The as-obtained powdered materials were annealed at 500 °C and subsequently underwent photocatalytic tests with paracetamol. Additionally, the TiO2 samples were modified with Ag+ co-catalysts (10-2 M), using photofixation by UV illumination. The photocatalytic activity of the Ag-modified powders was also tested in the photodegradation of a commonly used paracetamol in aqueous solution under UV light illumination. The obtained data exhibited that the annealed samples had better photocatalytic efficiency and decomposed paracetamol faster in comparison to the non-annealed sol-gel powders. The highest degradation efficiency was observed for the TBT/isop/Ag material, with degradation efficiencies average values of 65.59% and 75.61% paracetamol achieved after the third cycle of photocatalytic treatment. The co-catalytically modified powders had higher photocatalytic efficiency in comparison to the pure nanosized powders. Moreover, the sol-gel powders of TBT/EG, TBT/EG/Ag (10-2 M), TBT/isop, and TBT/isop/Ag (10-2 M) demonstrated the ability to retain their photocatalytic activity even after three cycles of use, suggesting that they could find practical use in the treatment of pharmaceutical wastewater. The observed photocatalytic efficiency and positive impact of silver make the prepared powders a desirable choice for pharmaceutical drug degradation, helping to promote environmentally friendly and effective wastewater treatment technology.

Dynamic Dissociation Behaviors of sII Hydrates in Liquid Water by Heating: A Molecular Dynamics Simulation Approach

An understanding of the dynamic behavior of subtle hydrate dissociation in the liquid water phase is fundamental for gas production from marine hydrate reservoirs. Molecular dynamics simulations are performed in this study to investigate the dissociation kinetics of pure propane and binary propane + methane sII hydrates in a liquid water environment. The results show that faster hydrate dissociation rates are observed at higher initial temperatures. The hydrate phase dissociates from the cluster surface to the inside in a layer-by-layer manner under the simulation temperature conditions, which is similar to the behavior of sI hydrates and is independent of the hydrate crystal type. Compared to the binary sII hydrate, the pure sII hydrate dissociates more easily under the same initial temperature conditions, which can be attributed to the stabilizing effect of guest molecules in the hydrate cages. The empty cages collapse in one step, in contrast to the two-step pathway induced by the guest-host interaction. In addition, a hydrocarbon phase forms in the binary hydrate dissociation system instead of nanobubbles. These results can provide molecular-level insights into the dynamic mechanism of hydrate dissociation and theoretical guidance for gas recovery by thermal injection from marine hydrate reservoirs.

Assessing the effect of a liquid water layer on the adsorption of hydrate anti-agglomerants using molecular simulations

We have performed Molecular Dynamics simulations to study the adsorption of ten hydrate anti-agglomerants onto a mixed methane-propane sII hydrate surface covered by layers of liquid water of various thickness. As a general trend, we found that the more liquid water is present on the hydrate surface the less favorable the adsorption becomes, even though there are considerable differences between the individual molecules, indicating that the presence and thickness of this liquid water layer is a crucial parameter for anti-agglomerant adsorption studies. Additionally, we found that there exists an optimal thickness of the liquid water layer favoring hydrate growth due to the presence of both liquid water and hydrate-forming guest molecules. For all other cases of liquid water layer thickness, hydrate growth is slower due to the limited availability of hydrate-forming guests close to the hydrate formation front. Finally, we investigated the connection between the thickness of the liquid water layer and the degree of subcooling, and found a very good agreement between our Molecular Dynamics simulations and theoretical predictions.

Structural Effects of Gas Hydrate Antiagglomerant Molecules on Interfacial Interparticle Force Interactions

Gas hydrate interparticle cohesive forces are important to determine the hydrate crystal particle agglomeration behavior and subsequent hydrate slurry transport that is critical to preventing potentially catastrophic consequences of subsea oil/gas pipeline blockages. A unique high-pressure micromechanical force apparatus has been employed to investigate the effect of the molecular structure of industrially relevant hydrate antiagglomerant (AA) inhibitors on gas hydrate crystal interparticle interactions. Four AA molecules with known detailed structures [quaternary ammonium salts with two long tails (R1) and one short tail (R2)] in which the R1 has 12 carbon (C12) and 8 carbon (C8) and saturated (C-C) versus unsaturated (C═C) bonding are used in this work to investigate their interfacial activity to suppress hydrate crystal interparticle interactions in the presence of two liquid hydrocarbons (n-dodecane and n-heptane). All AAs were able to reduce the interparticle cohesive force from the baseline (23.5 ± 2.5 mN m^-1), but AA-C12 shows superior performance in both liquid hydrocarbons compared to the other AAs. The interfacial measurements indicate that the AA with an R1 longer alkyl chain length can provide a denser barrier, and the AA molecules may have higher packing density when the AA R1 alkyl tail length is comparable to that of the liquid hydrocarbon chain on the gas hydrate crystal surface. Increasing the salinity can promote the effectiveness of an AA molecule and can also eliminate the effect of longer particle contact times, which typically increases the interparticle cohesive force. This work reports the first experimental investigation of high-performance known molecular structure AAs under industrially relevant conditions, showing that these molecules can reduce the interfacial tension and increase the gas hydrate-water contact angle, thereby minimizing the gas hydrate interparticle interactions. The structure-performance relation reported in this work can be used to help in the design of improved AA inhibitor molecules that will be critical to industrial hydrate crystal slurry transport.