Mechanical properties of temperature-responsive gels containing ethylene glycol in their side chains

Preparation and Properties of Physical Gel on Medical Titanium Alloy Surface

Medical titanium alloy Ti-6Al-4V (TC4) has been widely used in the medical field, especially in human tissue repair. However, TC4 has some shortcomings, which may cause problems with biocompatibility and mechanical compatibility in direct contact with the human body. To solve this problem, physical gels are formed on the surface of TC4, and the storage modulus of the formed physical gel matches that of the human soft tissue. 2-bromoisobutyryl bromide (BIBB) and dopamine (DA) were used to form initiators on the surface of hydroxylated medical titanium alloy. Different initiators were formed by changing the ratio of BIBB and DA, and the optimal one was selected for subsequent reactions. Under the action of the catalyst, L-lactide and D-lactide were ring-opened polymerized with hydroxyethyl methacrylate (HEMA), respectively, to form macromolecular monomers HEMA-PLLA₂₉ and HEMA-PDLA₂₉ with a polymerization degree of 29. The two macromolecular monomers were stereo-complexed by ultrasound to form HEMA-stereocomplex polylactic acid (HEMA-scPLA₂₉). Based on two monomers, 2-(2-methoxyethoxy) ethyl methacrylate (MEO₂MA) and oligo (ethylene oxide) methacrylate (OEGMA), and the physical crosslinking agent HEMA-scPLA_29, physical gels are formed on the surface of TC4 attached to the initiator via Atom Transfer Radical Addition Reaction (ATRP) technology. The hydrogels on the surface of titanium alloy were characterized and analyzed by a series of instruments. The results showed that the storage modulus of physical glue was within the range of the energy storage modulus of human soft tissue, which was conducive to improving the mechanical compatibility of titanium alloy and human soft tissue.

Controlling the mechanical properties of hydrogels via modulating the side-chain length

Even though the toughness of hydrogels is usually adjusted by changing the cross-linking density and structure, or the polymer concentration, we have discovered a new strategy to control the toughness via modulating the side-chain length. In this study, this strategy was applied to biocompatible poly(oligo(ethylene glycol) methyl ether methacrylate) with long ethylene-oxide side chains.

Fabrication and application of composite adsorbents made by one-pot electrochemical exfoliation of graphite in surfactant ionic liquid/nanocellulose mixtures

Previously, surfactant-assisted exfoliated graphene oxide (sEGO) formed with the triple-chain surfactant TC14 (sodium 1,4-bis(neopentyloxy)-3-(neopentylcarbonyl)-1,4-dioxobutane-2-sulfonate) was applied in wastewater treatment. The extent of dye-removal and the adsorption capacity of the sEGO formed with this triple-chain surfactant outperformed those of two other systems, namely, the di-chain version of TC14 (AOT14; sodium 1,2-bis-(2,2-dimethyl-propoxycarbonyl)-ethanesulfonate) and the single-chain surfactant sodium n-dodecylsulfate. In the present study, to further optimise the surfactant chemical structure, the sodium ion of TC14 was substituted with 1-butyl-3-methyl-imidazolium (BMIM) generating surfactant ionic liquids (SAILs; 1-butyl-3-imidazolium 1,4-bis(neopentyloxy)-3-(neopentyloxycarbonyl)-1,4-dioxobutane-2-sulfonate), hereafter denoted as BMIM-TC14. This SAIL, together with nanofibrillated kenaf cellulose (NFC), was used to electrochemically exfoliate graphite, yielding BMIM-TC14 sEGO/NFC composites. These highly hydrophobic polymer composites were then used for the removal of methylene blue (MB) from aqueous solution. ¹H NMR spectroscopy was used to elucidate the structure of the synthesised SAILs. The morphologies of the resulting nanocomposites were investigated using Raman spectroscopy, field-emission scanning electron microscopy, and high-resolution transmission electron microscopy. Analysis using small-angle neutron scattering was performed to examine the aggregation behaviour of sEGO and custom-made SAILs. Zeta potential, surface tension, and dynamic light-scattering measurements were used to study the aqueous properties and colloidal stability of the suspension. Amongst the surfactants tested, BMIM-TC14 sEGO/NFC exhibited the highest MB adsorption ability, achieving 99% dye removal under optimum conditions. These results highlight the importance of modifying the hydrophilic moieties of amphiphilic compounds to improve the performance of sEGO/NFC composites as effective adsorbents for wastewater treatment.

Lower Critical Solution Temperature Phase Transition of Poly(PEGMA) Hydrogel Thin Films

Surface-attached hydrogel films with well-controlled chemistry are a new approach of polymer thin layers and an actual alternative to polymer brushes and layer-by-layer assemblies. The advantage is that the thickness of hydrogel films can widely range from a few nanometers to several micrometers. Hydrogel films can also remarkably respond to stimuli such as temperature: (i) the thickness change is of great amplitude, fourfold and more, which could not be reached with the geometry of polymer brushes or layer-by-layer assemblies, (ii) the time response is very short (less than 1 s), and (iii) the swelling-to-collapse transition is narrow (a small temperature change of a few degrees may be enough). Poly(N-isopropylacrylamide) (PNIPAM) is the most temperature-responsive polymer investigated with a lower critical solution temperature (LCST) of around 32 °C. However, it is relevant to have the available polymers responding to various transition temperatures with the advantage of keeping the same chemistry. Poly[oligo(ethylene glycol) methacrylate] (PEGMA) meets these specifications since its transition temperature can be finely tuned with the number of oligo ethylene glycol units, while it attractively combines biocompatibility with PEG side chains. Here, we report the synthesis and the temperature-responsive properties of poly(PEGMA) hydrogel thin films. We used a simple, versatile, and well-controlled approach through thiol-ene click reaction, the so-called cross-linking and grafting, to synthesize surface-attached poly(PEGMA) hydrogel films with various thickness. We show that the transition temperature of poly(PEGMA) hydrogel films ranges from 15 to 60 °C if the number of PEG units is from 2 to 5. This transition temperature can also be finely adjusted for hydrogel films containing copolymers or mixing homopolymers of PEGMA with a suitable ratio. Moreover, the LCST properties, swelling-to-collapse amplitude and transition temperature, are not sensitive to salt. In particular, there is no effect on the LCST properties of surface-attached poly(PEGMA) hydrogel films in phosphate saline buffer, which is promising for applications in biology such as injectable hydrogels, drug delivery systems, hydrogel-based microfluidic valves, and flow switches for biotechnologies.